easy home EFM-05R Foot Massager Mat User Manual
- June 12, 2024
- EASY HOME
Table of Contents
easy home EFM-05R Foot Massager Mat
Warning
Before using, please clean and dry your feet or the sensations may not be felt
properly.
- DO NOT FOLD THE MAT TO AVOID damaging the MAT.
- Stop using this device immediately if you feel pain, discomfort, dizziness, or nausea, and consult your physician.
- Keep the foot mat away from heat or direct sunlight. Store it in a cool, dry place.
User Steps
The foot massage mat is compatible with Easy@Home TENS with correct connector buttons such as EHE015 (wireless TENS), and EHE029G (TENS with wires). See the button specifications below. Now we will take our TENS EHE015 and EHE029G as examples to show how this product works.
Using with Easy@Home Wireless TENS model# EHE015
Step 1: Attach the EHE015 control unit by aligning the female/male parts
directly.
Step 2: Put your feet on the mat. Each foot should be on one side like
below. Make sure to keep bare feet on the mat without socks so that the mat
gets good contact and works properly.
Step 3: Briefly press the ON/OFF button on the EHE015 device control unit
that is connected to the mat to turn it on.
Step 4: Press and release the + button to increase the intensity level on
the control unit.
There are 20 intensity levels to choose from when using the EHE015 Control
unit with the mat.
Step 5: Press and release the – button to decrease the intensity level.
Step 6: Press and hold the+ button for mode selection.
Step 7: Briefly presses the ON/OFF button to turn it off.
Using with Easy@Home Wired TENS model# EHE029G
Step 1: Snap the foot mat to the lead wire of either channel of EHE029G
Step 2: Put your feet on the foot mat, each foot should be on one side
like the instruction image in Step (2) of the previous page. Make sure to keep
bare feet on the mat without socks so that the mat gets good contact and works
properly.
Step 3: Slide the “ON/OFF” switch to turn on the power on the EHE029G
tens device.
Step 4: Press “M” (as shown in the image below) to select one of the
stimulation modes on your tens device next.
Step 5: Adjust the stimulation intensity. Press and release the”+” button
to increase the stimulation intensity, and press and release the button to
decrease the intensity from your tens device control.
Note 1: With a fast increase in intensity, you may experience sensations
like tingling, vibration, etc. Therefore, it is highly recommended to
gradually increase the intensity, and stop increasing when a comfortable level
is reached.
Note 2 : Make sure you are increasing/decreasing the correct channel that
you are actually connected to when using.
Step 6: Press and hold the middle round button for 2 seconds to adjust
the timer:10, 20, 30, 40, 50, 60 minutes options.
Step 7: When time is completed, the device will turn off automatically.
Or slide the “ON/OFF” switch to turn off the device and then remove your feet
from the massage mat.
Specifications
-
Size: 13.9411.97 inch ( 35.430.4cm)
Note: Due to manual measurement, there will be an error of +/-0.3-0.5 cm -
Materials: styrene-butadiene rubber (SBR) and conductive silicone
-
The distance between the two snap buttons is about 3 cm and the whole length including the buttons is 3.7cm.
Cleaning and Maintenance
Please WIPE with a damp cloth using clean water or neutral detergent. Then dry
with a lint FREE dry cloth.
Jfualthcare-JY\anager.com
Questions or comments?
Please call toll-free: 1-855-822-6999
M-F 9 a.m.-5 p.m. CST
E-mail: service@healthcare-manager.com Easy Healthcare Corporation
Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>