PowerPac PP939 Pro Hair Cutter User Manual
- June 12, 2024
- PowerPac
Table of Contents
Power Pac PP939 Pro Hair Cutter
PARTS & DESCRIPTION
LIST OF COMPONENTS
- Top Blade
- Bottom Blade
- Guide Comb (3/6/9/12 mm)
- Blade Lever
- ON/OFF Switch
WARNINGS
ATTENTION :
Read this booklet carefully as it contains important instructions for a safe
installation, use and maintenance.
Important instructions to be kept for future reference.
The following basic precautions should always be followed when using
electrical appliances:
-
Read all instructions before using the appliance.
-
This appliance must be used only for the purpose it was expressly designed; any use NOT complying with the instructions contained in the manual is considered inappropriate and dangerous. The manufacturer is NOT responsible for possible damages caused by the inappropriate and/or unreasonable use.
-
This appliance is NOT suitable to be used or stored near heat sources (open flame, ovens, heaters, stoves, etc.) and/or in an explosive environment (in the presence of flammable substances such as gas, vapour, mist or dust, in atmospheric conditions when, after ignition, the combustion is spread in the air). Items containing these substances should never be placed in the appliance, and never be used to clean the appliance in order to avert the risk of fire or explosion.
-
The packing materials (plastic bags, expanded polystyrene, etc.) must be kept out of the reach of children or disabled persons since they represent potential sources of danger.
-
The installation/assembly of the appliance will be made in accordance with the indications of the manufacturer. A wrong procedure may cause damages to persons, animals or objects, for which the manufacturer cannot be considered responsible.
-
Before use, check the integrity of the appliance and charging cable. DO NOT use the appliance with a damaged Guide Comb, with teeth missing from the Blades, or with unaligned Blades. DO NOT pull, twist or bend the charging cable, nor place heavy objects on it; or use a charging cable that is worn or frayed. If the charging cable is damaged, it must be replaced by the manufacturer or its service agent or a qualified technician in order to avoid a shock hazard.
-
Before powering the appliance make sure the rating (voltage and frequency) corresponding to the grid and the socket is suitable for the charging cable, and that the wall socket is properly grounded.
-
DO NOT power the appliance using multiple sockets. If possible, avoid the use of adapters and/or extension cables; if their use is absolutely necessary, use only materials in compliance with the current safety regulations and according to the electrical parameters of the adapters.
-
The appliance must NOT be switched on using external timers and/or other remote control appliances which are not specified in this manual.
-
Only use original components & accessories provided by the manufacturer. Any non-original components & accessories (e.g. Blades & Guide Combs) NOT recommended by the manufacturer may cause injuries to persons or damage to the appliance. Doing so will void the warranty and may cause serious injury.
-
If you are using the appliance for the first time, you should:
a. Ensure that the appliance is switched off before cleaning the appliance. If the exterior of the appliance is sticky, you can apply a small amount of detergent and clean it with a soft wet cloth. DO NOT use cleaners or chemical substances. DO NOT use metal scouring pads. DO NOT immerse the appliance, excluding the Blades and the Guide Comb, in water or other liquids, wash it under the tap, or let any liquid flow into the internal casing of the appliance to prevent electric shock. DO NOT clean any part of the appliance in the dishwasher. Wipe the appliance’s surface with a dry cloth.
b. Clean the Blades immediately after using the appliance. To remove the Blades (after removing the Guide Comb), hold the appliance and press your thumb against the flat section of the Blades and push upwards. You can rinse the Blades & Guide Comb under running water. Dry them before re-attaching it to the appliance. To re-attach the Blades, slip the bottom of the Blades into the catch and, using your thumb, press the Blades into the appliance.
The Blades have a fixed life. In order to obtain the best result, please replace the Blades regularly. Using blunt, deformed or damaged Blades may result in skin irritation or injury. Apply oil to the Blades prior to each use. DO NOT use hair oil, grease, oil mixed with kerosene or any solvent. To re-align the Blades, switch OFF and unplug, loosen screws slightly, match the Top and Bottom Blade teeth up, point for point, with the end of the Top Blade teeth 1.2 mm back from the end of the Bottom Blade teeth, and tighten the screws Make sure to remove any label or protective sheet which may prevent its proper functioning.
DO NOT:
• use the appliance to trim artificial hair or animal hair;
• use the appliance on skin that is wounded, sunburnt, cut or blistered;
• use the appliance in an inverted position as it may cause the Blades to cut too deep, leading to injury;
• cover the appliance during functioning;
• place the appliance in the microwave or conventional oven, or pour boiling water over any part of the appliance in order to sterilize it;
• place the appliance on any surface while it is operating;
• insert objects or body parts inside the protection cover of the appliance; touch the Blades with your fingers or any utensil while the appliance is operating to avoid personal injury or damage to the appliance;
• operate the appliance for more than 2 minutes without interruption. Let the appliance rest for 1 minute between processing cycles. After 3 processing cycles, allow an interval of 10 minutes to let the appliance cool down before the next use, so as to prolong its service life.
DO NOT allow the appliance to idle while in operation;
• press the Blade Lever or the ON/OFF Switch too forcefully;
• leave the appliance unsupervised during operation.
-
During operation, DO NOT use the appliance whilst showering or touch the appliance with wet body parts, and it is recommended to have between you and the standing surface, an isolating element (for example, wearing shoes with rubber soles.
-
Avoid placing the appliance or charging cable on abrasive or sharp surfaces or in positions where it can be damaged easily. The cable must NOT be placed under carpets, or covered with throw rugs, runners or similar. Arrange the cable away from the high traffic area, and where it will NOT be tripped over.
-
Always remember to unplug the cable of the appliance after use, before storing, using, cleaning or performing any maintenance operation.
-
Avoid carrying out operations which are NOT specified in this manual (such as disassembling and/or altering).
-
In case of malfunction or anomaly during the functioning, switch off the appliance immediately and check the cause of the anomaly, if possible, with the support of a qualified person.
-
If smoke is observed coming out of the appliance, switch off the appliance immediately. Let the appliance and its contents cool before attempting to remove the Blades and the Guide Comb out of the appliance.
-
This appliance is NOT intended for commercial use but to be used in households and similar applications.
-
DO NOT use or store the appliance outdoors. Store and use the appliance only indoors, or in any case, protected from weathering such as rain, direct radiation of the sun and dust.
Safety Protection
If the appliance overheats, the thermal switch will be activated, leading to the motor being shut off. Press the ON/OFF Switch OFF. Allow the appliance to cool for at least 15 minutes before using the appliance.
The Blade Lever
The Blade Lever allows you to gradually change the closeness of the cut
without changing the Guide Comb. When the Blade Lever is at its highest
position, your hair will be very short. When the Blade Lever is at its lowest
position, your hair will be longer, just like using Guide Comb 3 mm (⅛ in).
The Blade Lever extends the life of the Blades since a different cutting edge
is used for each setting.
With the Clipper in operation, rapidly move the Blade Leaver from “Close cut”
to “Longer cut” a few times. This action removes hair that had become wedged
between the Top & Bottom Blades, without the need to loosen the screws and
remove the Blades. With all the wedged hair removed, if the Clipper stops
cutting and the Blades are jammed even with this action being repeatedly
carried out, the Blades have become dull, and should be replaced.
HOW TO CUT
Begin with the Guide Comb of the longest length – ④ which leaves 12mm (½ inch)
of hair until you get used to the length to which each Guide Comb cuts the
hair. To attach a Guide Comb, hold it with the teeth pointing upwards and
slide it along the Blades until the front of the Guide Comb firmly seats
against the Blades. To remove the Guide Comb, pull it upward and away from the
Blades.
Comb the DRY hair frequently during cutting to check for uneven strands and to
remove cut hair.
Guide Combs
To cut hair in the region
Nape of the Neck
- Attach Guide Combs ① or ②.
- Hold the Clipper with the Blade teeth pointing upwards.
- Begin at the centre of the head at the base of the neck, and stop at the level near the middle of the ears.
- Slowly work the Guide Comb through the hair without forcing it through as you work upwards and outwards through the hair, trimming a little at a time.
- Continue on each side of where you started until the entire nape of the neck is shaved.
Back of the Head
- Attach Guide Combs ③ or ④.
- Hold the Clipper with the Blade teeth pointing upwards.
- Begin at the centre of the head where you left off earlier, and stop at the level near the top of the head.
- Slowly work the Guide Comb through the hair without forcing it through as you work upwards and outwards through the hair, trimming a little at a time.
- Continue on each side of where you started until the entire back of the head is shaved.
Side of the Head
Attach Guide Combs ① or ② and trim both sideburns.
Then attach Guide Combs ③ or ④.
Hold the Clipper with the Blade teeth pointing upwards.
Begin at the top of the sideburns, and end at the level near the top of the
head.
Top of the Head
-
For hair of normal length, use Guide Combs ③ or ④.
-
If you desire a crew-cut, use Guide Combs ① or ②.
-
It is advisable to use a longer Guide Comb first, and then use a shorter one.
-
For long hair which you desire to keep a certain length, use the Comb provided to lift the hair to the desired length and cut ABOVE the Comb.
-
In this case, you need not attach the Guide Comb.
-
Alternatively, you can also use your fingers to lift the hair to the desired length, and cut the hair ABOVE the fingers.
-
In this case, you need not attach the Guide Comb.
In all cases: -
• Hold the Clipper with the Blade teeth pointing upwards.
Begin where you left of at the back of the head, and end at the front of the head, against the direction of hair growth. In some cases, that would mean cutting from the front to the back.
The Finishing Touches
- Remove the Guide Comb from the Clipper. Carefully trim the hair all around the head evenly.
- To achieve clean straight lines at the sideburns, turn the Clipper over.
Then, press the Clipper at right angles to the head, with the tips of the Blades lightly touching the skin and work downward. This achieves as clean a cut as you would from a razor.
Short Tapered Styles – ‘Flat Tops’
- Attach Guide Comb ④.
- Hold the Clipper with the Blade teeth pointing upwards.
- With the Guide Comb flat against the head, begin at the centre of the head at the base of the neck, and stop at the crown.
- Continue on each side of where you started until the entire back and sides are shaved.
- Then, cut the hair from the front of the head to the crown, against the direction of hair growth. (refer to diagram)
- Remove the Guide Comb from the Clipper. To achieve a ‘Flat Top’, use the Comb provided and cut the hair ABOVE the Comb.
- Attach Guide Comb ①.
- Hold the Clipper with the Blade teeth pointing upwards.
- Taper the hair down to the neckline as desired.
- Comb hair and check for uneven areas. Use the Clipper to smoothen out such areas.
ENVIRONMENTAL TIP
This appliance, along with all other electronic appliances, should, when it is
no longer capable of functioning, be disposed with the least possible
environmental damage according to the local regulations in your area. In most
cases you can discard the appliance at your local recycling centre.
DISPOSAL: Do not dispose this appliance as unsorted municipal waste.
Collection of such waste separately for special treatment is necessary.
Risk of child or animal entrapment
Before you discard this appliance, please remove all doors and leave the
shelves inside so that children or animals may not easily get trapped inside.
WARRANTY
Warranty Conditions
- This warranty provides against defective materials and manufacturing faults throughout for two years from the date of purchase of the appliance. The warranty on the Compressor is 10 years subject to the same conditions as above.
- This warranty also does not cover normal wear and tear, replacement of consumable materials and accessories, and the cost of maintenance of the appliance.
- This warranty does not cover the repair or replacement of part/s damaged by misuse, accidents, negligence, alterations, or modifications in any way, or repairs done by any repair organisation without the prior consent of Power Pac Electrical Pte Ltd.
- Repair and service are to be performed at: 5 Changi South Lane #03-01 Singapore 486045. A transport fee will be charged for personal doorstep service.
- The original purchaser of the appliance must furnish proof of purchase to our Service Centre with the email or number as registered during submission of warranty when this appliance is sent for repair/service. Failure to do so may delay the receipt of said repair/service by the customer.
- Under no circumstances whatsoever shall the serial number be erased, defaced or altered by the customer and/or his representatives, or the dealer and/or his agents. Failure to ensure this shall invalidate the warranty.
- This warranty is deemed to be void if the defect is cause by the attack of household pests, fire, lightning, natural disasters, pollution, abnormal voltage or the usage of generators.
- This warranty is valid in Singapore only.
- This warranty will be honored subject to the customer’s registration of the warranty inclusive of original invoice or valid purchase receipt. Failure to present these documents will result in denial of service. However, if the customer still requests that the defective appliance be repaired, Power Pac Electrical Pte Ltd may, at its discretion, repair the appliance but impose a labour charge, as well as the costs of the replacement parts, to be borne solely by the customer.
- Please refer to the attached picture for the location of one of our appliance’s serial number, as an example.
Please complete the on-line registration warranty form available on our website. There is no further requirement to send us any hard copy as part of our efforts to save the environment. In accordance with the terms and conditions of this limited warranty as stated above, PowerPac Electrical Pte Ltd, at its expense shall provide free services for the appliance within the warranty period from its date of purchase from our Authorised dealers.
SPECIFICATION
MODEL
|
VOLTAGE
|
WATTS(W)
---|---|---
PP939
|
220-240V ~ 50/60Hz
|
9W
Customer Support
| | |
---|---|---|---
sales@powerpac.com.sg|
www.powerpac.com.sg|
@powerpacsg
|
Powerpac Sg
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>