V I V O STAND-V003T Triple Monitor Desk Mount Instruction Manual
- June 12, 2024
- V I V O
Table of Contents
V I V O STAND-V003T Triple Monitor Desk Mount
Scan the QR code with your mobile device or follow the link for helpful videos
and specifications related to this product.
Instruction Manual https://vivo-us.com/products/stand-v003t
-
www.vivo-us.com
Chat live with an agent!
WARNING! If you do not understand these directions, or if you have any
doubts about the safety of the installation, please call a qualified
technician. Check carefully to make sure there are no missing or defective
parts. Improper installation may cause damage or serious injury. Do not use
this product for any purpose that is not explicitly specified in this manual.
Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting,
incorrect assembly or inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS
REQUIRED.
PACKAGE CONTENTS
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
TOOLS NEEDED
ASSEMBLY STEPS
STEP 1
OPTION A: Clamp Installation
Remove adhesive backing from Rubber Pads (K) and place them on the underside
of Clamp (D). Assemble Clamp (D) to Bottom Pole (E) using M3x16mm Screws (S-A)
and 4mm Allen Wrench (T-A). Then secure Clamp (D) to the desktop.
OPTION B: Grommet Base Installation
For grommet hole mounting, remove the screw in the top of Hand Bolt (D1) on
Clamp (D). Stick Rubber Pads (K) to bottom of Grommet Base (I). Attach Grommet
Plate (L) to Hand Bolt (D1) and run through grommet hole into Grommet Base (I)
and thread into Pole (E).
STEP 2
Slide Cable Clip (H) and Arm (C) onto Bottom Pole (E). Secure Arm (C) in
place using 6mm Allen Wrench (T-C). Screw Pole Connector (G) onto Bottom Pole
(E), then screw Top Pole (F) into Pole Connector (G). Tighten the set screws
in Pole Connector (G) using 3mm Allen Wrench (T-A).
STEP 3
Slide Cable Clip (H) and VESA Bracket (B) onto Top Pole (F). Secure VESA
Bracket (B) in place using 6mm Allen Wrench (T-C).
STEP 4
OPTION A: Flat Back Monitor
Assemble VESA Plates (A) to back of monitors using Screw (M-A or M-C) and M5
Washers (M-H).
OPTION B: Curved Back Monitor
Assemble VESA Plates (A) to back of monitors using Screws (M-B or M-D). If
screws are too long, Spacers (M-G) may be required.
STEP 5
Slide VESA Plates (A) with monitors onto VESA Bracket (B) or Arm (C).
STEP 6
Secure bottom two monitors to Arm (C) using VESA Caps (J) and M3x8mm Screws
(S-B). Tighten with a Phillips screwdriver. Secure top monitor to VESA Bracket
(B) using Thumbscrew (S-C). Use 6mm Allen Wrench (T-C) to adjust the tilt.
STEP 7
Manage cables using the cable management clips in Arm (C) and Cable Clips
(H). Store Allen Wrenches (T-A, T-B, T-C) in Cable Clip (H) for future
adjustments.
STEP 8
Level bottom monitors by turning VESA Caps (J) using 6mm Allen Wrench
(T-C). Adjust monitors as desired.
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Triple Monitor Desk Mount – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>