BLAUPUNKT P3PM2T2 Portable Charging Box Instructions
- June 12, 2024
- Blaupunkt
Table of Contents
- P3PM2T2 Portable Charging Box
- Introduction to the Portable EV Charger ( Mode 2 )
- Explanation of the operating display and technical parameters
- Use of the charger – start charging
- Use of the charger – stop charging
- Display Light Status
- Function: Switch Current
- Function: Timer function
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
EV Portable Charger
User Manual
Enjoy it
Please read this instruction carefully before using the product.
P3PM2T2 Portable Charging Box
EV Portable Charger
Please carefully read the following instructions before charging your
Electrical Vehicle, be aware of the hazards involved with electrical circuity
and standard practices for preventing accidents.
Introduction to the Portable EV Charger ( Mode 2 )
CAUTION
- Use the power source with external upstream Circuit Breaker.
- Make sure the charger is used in a safe, secure place and well out of the reach of young children or pets.
- Please use the charger in a dry, well ventilated and secure place. Keep weel out of reach of young children or pets. Avoid water pouring directly onto the power plug.
- Do not open the enclosure while charging or with the power on.
- Do not maliciously damage the product.
Introduction to the Portable EV Charger ( Mode 2 )
Model| Power Supply
Type| Cable Total
Length| Voltage| Current| Connector
Type
---|---|---|---|---|---
P1PM2T2| Single-phase| 8m| 200-250V| 8/10/13/16A| T2
P1PM2T1| Single-phase| 8m| 200-250V| 8/10/13/16A| T1
P1PM2T2C| Single-phase| 8m| 200-250V| 8/10/13/16A| T2
P3PM2T2| Three-phase| 8m| 380-450V| 8/10/13/16A| T2
P1PM2T2BS| Single-phase| 8m| 200-250V| 8/10/13/16A| T2
P1PM2T1BS| Single-phase| 8m| 200-250V| 8/10/13/16A| T1
Explanation of the operating display and technical parameters
1. Model: P3PM2T2
Explanation of the operating display
| Power light
---|---
| Charge lamp
| Trouble lamp
| Current switch button
00:00:03| Charging time
| Temperature
| PE Detection (Earthing Detection)*
405V| Voltage
0.89kw| Power
16A| Rated current
3.9A| Constant current
0.002kwh| Electricity consumption
| Time function button
*Warning :
Before charging, the user must check the “ ” symbol on the charger’s
display. If “ ” is displayed, the charger operates without an Upstream
protective conductor ( PE )
Only trained electricians are allowed to use the charger if the “ ” symbol is
displayed.
Control box:
Technical Parameters
| Dimensions (L x W x H) | 260 x 100 x 72.5 mm |
|---|---|
| Weight | 3Phase: 3.35 kg |
| Protection Degree ( Control box) | IP65 |
| Operating Temperature | -30°C to +50°C |
Explanation of the operating display and technical parameters
2. Model: P1IPM2T2/P1PM2T1 /P1PM2T2C / P1PM2T2BS / P1PM2T1BS
Explanation of the operating display
| Power light
---|---
| Charge lamp
| Trouble lamp
| Current switch button
00:00:03| Charging time
| Temperature
| PE Detection (Earthing Detection)*
245V| Voltage
0.89kw| Power
16A| Rated current
3.9A| Constant current
0.002kwh| Electricity consumption
| Time function button
* Warning :
Before charging, the user must check the “ ” symbol on the charger’s
display. If “ ” is displayed, the charger operates without an Upstream
protective conductor ( PE )
Only trained electricians are allowed to use the charger if the “ ” symbol is
displayed.
Control box:
Technical Parameters
| Dimensions (L x W x H) | 260 x 100 x 72.5 mm |
|---|---|
| Weight | 1 Phase: 2.65 kg |
| Protection Degree ( Control box) | IP65 |
| Operating Temperature | -30°C to +50°C |
Use of the charger – start charging
Start Charging
| Step | Illustration | Operation |
|---|---|---|
| 1 | Insert the plug into the correct power supply socket. | |
| 2 | Remove the protective cap and fully insert the charging |
connector into the EV charging port.
3| | Start charging
Danger
Do not use the product if it appears to be damaged or the cable is broken.
Do not disassemble or assemble the connector and change the internal parts Do
not clean the products using chemicals or cleaning the EV car while charging.
Use of the charger – stop charging
Stop Charging
| Step | Illustration | Operation |
|---|---|---|
| 1 | Disconnect the plug from the power supply socket. | |
| 2 | Disconnect the charging connector from the EV car. | |
| 3 | Close the protective shell of EV charging port,then cover the protective |
cap of the charging
connector.
4| | Put the portable charger into the bag.
Display Light Status
Display Light Status
Indicator Light| Status| Indicator Light| Status|
Indicator Light| Status
---|---|---|---|---|---
| Off| | Blink| | On
| Off| | Blink| | On
| Off| | Blink| | On
Operation:
1| Power Off| | |
---|---|---|---|---
2| Check| | |
3| Standby| | |
4| Connected| | |
5| Charging| | |
6| Charge Complete| | |
Troubleshooting:
CP Error| | |
---|---|---|---
Relay Error| | |
Over/Under Voltage| | |
Over current protection| | |
Electric leakage protection| | |
No ground connection| | |
Temperature warning| | |
Persistent high temperature| | |
Function: Switch Current
Switch Current:
CAUTION
In order to switch charging current, Please make sure the power plug is
firmly inserted into the socket and plug for the EV vehicle is disconnected.
| Step | Statu | |
|---|---|---|
| 1.Insert the plug into the correct power supply socket. | Ready | |
| 2.Press the “Amps” switch button for 2 seconds | Enter setting the switch |
current mode
3.Continue to press the button briefly. The current will be changed. ( switch
between 8-10-13-16A)| | Setting the current of User’s request
4 Press the button for 2s again.| | Setting successfully
Please complete setting within 4 seconds at each step, otherwise the feature setting will fail.
Function: Timer function
Timer function:
CAUTION
In order to switch charging current, Please make sure the power plug is firmly
inserted into the socket and the plug for EV vehicle is disconnected.
| Step | Statu | |
|---|---|---|
| 1.Insert the plug into the correct power supply socket. | Ready | |
| 2.Press the “Time” switch button for 2 seconds. | Enter setting the delay |
time mode
3.Continue to press the button briefly.The time
will be changed.( Switch between 1/2/4/6/8/10H )| | Setting the delay time of
User’ s request
4 Press the button for 2s again| | Setting successfully
Please complete setting within 4 seconds at each step, otherwise the feature setting will fail.
Notice:
In case you want to cancel the timer setting – you can use one of the two
options below:
- Directly to disconnect the plug from the outlet socket.
- Press the Time button for 5s.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>