EPOMAKER TH68 Pro 5.0 Wired Mechanical Gaming Keyboard Instruction Manual

EPOMAKER TH68 PRO
QUICK START GUIDE

65% Hot Swappable RGB 2.4Ghz/Bluetooth 5.0/Wired
Mechanical Gaming Keyboard
Should you require more assistance please email us at support@epomaker.com

TH68 Pro 5.0 Wired Mechanical Gaming Keyboard

FN + ESC
(HOLD 3S)| Reset the Keyboard| FN + BACKSPACE| Turn On/Off Backlights
FN + ESC
(SHORT PRESS)| `| FN + DEL
(SHORT PRESS)| Toggle RGB Effects
FN+SHIFT+ESC| ~| FN + DEL
(HOLD 5S)| Record RGB
FN + B| Battery Check| FN + PGDN| Toggle RGB Colors
FN+SPACEBAR
(HOLD)| Check Layer & Mode| FN + PGUP| Toggle Side Lights
FN + Z/X/C/V| Switch among the Layers 1/2/3/4| FN + ↓| Backlights Brightness –
FN + Q| Short Press to Switch to BT1;
Long Press to Pair Devices| FN + ↑| Backlights Brightness +
FN + W| Short Press to Switch to BT2;
Long Press to Pair Devices| FN + ←| Backlights Speed –
FN + E| Short Press to Switch to BT2;
Long Press to Pair Devices| FN + →| Backlights Speed +
FN + R| Short Press to Switch to 2.4G Mode;
Long Press to Pair Devices| |

PAIRING BLUETOOTH

Toggle the switch in the back to make sure that the keyboard is under the wireless mode:

1. Hold Fn+Q/W/E for 3-5 seconds till the indicators flashes fast in blue, the keyboard is ready to pair.

2. Turn on your Bluetooth device and find “TH68 PRO BT5.0” or “TH68 PRO BT3.0”, then connect.
   When the keyboard is connected to the Bluetooth device, the light on the Q/W/E key stops flashing and the connection is done.

3. Press Fn+Q/W/E to toggle between the Bluetooth devices 1/2/3.

PAIRING WIRELESS 2.4GHz

Toggle the switch in the back to make sure that the keyboard is under the wireless mode:

1. Hold Fn+R for for 3-5 seconds till the light flashes fast in green, the keyboard is ready to pair.
2. Insert the 2.4G dongle to your device, the R key stops flashing green and the connection is done.

CHECK BATTERY

Hold Fn+B, the keys from 1! to 0) lights up to show the battery percentage; for example, if the keys from 1! to 6^ light up when holding Fn+B, it means that the battery life is currently 60%; if keys of 1!-0) light up, battery life is 100%.

CHECK LAYER AND MODE

Hold Fn+Spacebar, the indicators of Z/X/C/V, Q/W/E/R and W/M light up to show at which layer and which mode the keyboard is; for example, if the keys of X, E and M light up when holding
Fn+Spacebar, it means that the keyboard is in layer 2 in the Mac mode and connected to BT3 device.

SPECS

REPLACING KEYCAPS AND SWITCHES
For a full guide on how to remove keycaps and switches scan the QR Code or type in your browser:
https://epomaker.com/blogs/guides/diy-guide-how-to-remove-and-replace-your- mechanical-keyboard-switches

Remove Switches

1. Grab your Switch Removal Tool and align the gripping teeth vertically (on the Y-Axis) at the center of the switch, as shown in the example graphic above.
2. Grab the switch with the Switch Puller and apply pressure until the switch releases itself from the plate.
3. Using firm but gentle force pull the switch away from the keyboard using a vertical motion.

Install Switches

1. Check that all the switch metallic pins are perfectly straight and clean.
2. Align the switch vertically to have the Gateron logo facing north. The pins should align themselves to the keyboard PBC.
3. Press the switch down until you hear a click. This means your switch clips have attached themselves to the keyboard plate.
4. Inspect the switch to ensure it’s properly attached to your keyboard, and test it.

Note: If the key doesn’t work its possible you may have bent one of the switches while installing it. Pull the switch out and repeat the process.
Pins may be damaged beyond repair and need replacement if this process is not done correctly. Never apply excessive force when replacing keycaps or switches. If you cannot remove or install keycaps or switches please contact customer service as soon as possible to avoid damage to the keyboard due to operating errors.

TECHNICAL ASSISTANCE

For technical assistance, please email support@epomaker.com with your purchase order number and a detailed description of your issue.

We normally respond to enquiries within 24 hours. If you purchased your keyboard from a distributor or not from any official store of Epomaker, please contact them directly for any additional help.

COMMUNITY FORUMS

Join our community and learn together with other keyboard enthusiasts.
 https://discord.gg/2q3Z7/7C2
 https://www.reddit.com/user/epomaker/

WARRANTY

EPOMAKER’s Warranty covers any factory defects that might affect the proper functionality of your purchase. It doesn’t cover any damage that may occur from normal wear and tear.
If your product is defective we will send you a replacement unit. Replacement units might require you to send the defective unit back to Epomaker.
We provide a 1 year warranty for our products when bought from our website (EPOMAKER.com). Your item will not be covered by your 1 year warranty if the inspection shows any sign of modification or changes unsupported by the original product, these include: Changing internal components, Assembling and reassembling the product, Replacing Batteries, etc.
We will ONLY cover the item if it is bought from our official stores. You do not have a warranty with us if you bought the item from another reseller or likewise. Please contact the store that you bought your product from to resolve issues.

Made in China
Manufacturer: Shenzhen Changyun Technology Co., Ltd.
Address: F/2, Building 1, No.32 Makan South Road, Makan Community,
Xili Street, Nanshan District, Shenzhen, Guangdong, CN
Email: support@epomaker.com
Web: www.epomaker.com

APEX CE SPECIALISTS LIMITED
Unit 3d North Point House, North Point Business Park,
New Mallow Road Cork, T23 AT2P, Ireland
Contact: Wells
Phone: +353212066339
Email: info@apex-ce.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>