HAOCHENG T31 Smart Band User Manual

HAOCHENG T31 Smart Band

Hello, thank you for choosing our smart band. For convenience when you using this device first time, please read the instructions carefully and follow the steps in the user manual.

Component Introduction

Note : Press and hold the button to turn on the watch.

Instruction for Charging
Charging the device to active before the first time using; To charge your device, plug the charging cable into the adapter or USB port on your computer.

Install bracelet APP
Scan the following QR codes or go to the major APP store to download and install the APP “GloryFit “.

Device requirements: iOS 10.0 and above; Android 5.0 and above.

Main function interface

Home screen/dial
On the home screen, press and hold the touch screen, swipe left and right to switch, and click OK. There are these styles of dials.

• Step/distance/calorie
  View the number of steps taken at any time of the day, walking distance and calories burned, can be synchronized to the APP “GloryFit” in time to view the sports data.

• Heart rate interface
  Switch to the heart rate test interface to enter the heart rate real time monitoring, measurement data can be synchronized to the APP “GloryFit” in time, and have a test report.

• Blood oxygen interface

• Switch to the blood oxygen test interface to enter the real-time detection of blood oxygen. Test results are displayed directly on the bracelet interface.

• Weather interface
  The weather interface will display the current weather, weather information needs to be connected to the APP “GloryFit” can get data, if disconnected for a long time, weather letter information will not be updated.

• Stopwatch
  Swipe right, find the function interface, click the stopwatch icon to enter the stopwatch function.

• Message interface
  On the main interface, slide into the message interface and click the message icon to view the message. Click to turn the page to view the message or right to exit.

Sports interface
Press the button on the main interface to enter the motioninterface right slide back to the main interface. Click on the motion map the target can enter the motion mode detection. Running, cycling swimming, skipping, table tennis, badminton, tennis, etc.
Press the button on the main interface to enter slide up and down to switch, click to start calculation, right slide to exit the current sports mode.

Setting function interface
In the main interface, slide down to enter the setting function interface, you can choose “Find phone”, “Brightness adjustment”, “About”, “Settings” item. Click the icon to enter the corresponding function settings.

About Interface
Click on the “About” icon to display the machine model and the last four digits of the Bluetooth address.

Reduction interface
Click the “Restore” icon, you can restore the bracelet.

Shutdown interface
Click the shutdown page, you can shut down.

Other function reminders
The reminder function needs to set the reminder switch on the APP “GloryFit” side, and keep the phone and bracelet successfully connected in the Bluetooth state, and the message is a vibration reminder.

Sleep monitoring function
When you fall asleep, the watch will automatically determine the sleep detection mode, automatically detect your deep sleep/light sleep/wake time throughout the night, and calculate your sleep quality. Sleep data can only be viewed on the APP “GloryFit”.
Note : Sleep data will only be available when you wear the watch to sleep.

Matters needing attention

1. It is forbidden to use adapters with charging voltage greater than 5V and charging current greater than 2A, and the charging time is 2-3 hours.
2. It is forbidden to charge in the case of water stains.
3. This product is an electronic product, not as a medical reference measurement data is for reference only.

Q&A

1. Why can’t push the call information or content?
2. Android QQ/WeChat reminder service access When the user opens the QQ and WeChat reminder switch for the first time, the APP “GloryFit” will obtain the corresponding permissions, and check the program in the APP “GloryFit” to make it obtain the corresponding permissions.
3. When iOS (call, SMS, QQ, WeChat) reminder switch, the system will automatically pop up pairing request, and users only need to select pairing.

Turn on and enter the home screen Steps for viewing E-Label:

Service email: [email protected]

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>