HECHT 624 Box Knives Shredder User Manual
- June 12, 2024
- HECHT
Table of Contents
624 BOX
KNIVES SHREDDER
RIGINAL INSTRUCTIONS FOR USE
624 Box Knives Shredder
This manual contains important information about safety, installation, operation, maintenance, storage, and troubleshooting. Keep this manual in a safe place to be able to find information in the future or for other users. Given the constant technological development and adaptation to the latest exacting standards of the EU technical and design changes may be carried out without prior notice. Photographs are for illustrative purposes only, and may not exactly match the product itself. It is not possible to exercise any legal claims associated with this operator’s manual. In case of doubt, contact the importer or retailer.
SAFETY SYMBOLS
The rating plate on your tool may show symbols. These represent important information about the product or instruction its use.
*| The following warning symbols are to remind you of the safety
precautions you should take when operating the machine.
---|---
| Read the instruction manual.
| Use eyes, ears and head protection
| Risk of injury ejected parts.
| Keep other people and domestic animals at a safe distance.
| Warning: Risk of hand and feet injury.
| Keep feet and hands in safety distance.
| Don´t touch if is the machine on the move.
| Switch off the engine before cleaning of the exhaust port.
| Risk of injury by rotating parts.
| Attention! Kickback!
| Do not touch individual parts of the machine before they fully stops.
---|---
| Petrol is a fire hazard and can explode. Smoking and open fire are
prohibited.
| Risk of explosion! Do not top up with fuel with engine running.
| Attention toxic fumes!
| Warning! Do not use the appliance in closed or poorly ventilated
environments. Risk of breathing in toxic gases!
| Switch off the engine and remove the key before working on the machine!
| Primer
| Recoil starter symbol
| Oil
| Choke symbol
| Fuel
| Fuel – Empty fuel tank
| Stop
| Safety key
| Engine displacement
| Max. engine power
| Weight
Power voltage| 230-240 V – 50 Hz
---|---
Rated power (P40)| 2500 W
No-load rotation speed| 4050 min -1
Max. blade rotation speed| 6500 min -1
Thickness of branches| Ø 40 mm
Weight| 14 kg
Packaging size| 48,5 × 38,5 × 55,5 cm
Collecting catcher volume| cca. 50 l
IP Code| IPX4
Protection class| II
Measured noise pressure level at the place of operation| LPA = 95,7 dB (A)
K = 3 dB (A)
- Continuous operation with intermittent loading (4 min load – 6 min idle)
Max. diameter of crushed branches depends on the type of wood and the condition of the material for making chaff.
For hardwood (eg, oak / beech tree branches) is the max diameter of crushed branches less than softwood (eg pine / spruce wood). For dry or knaggy wood the thickness of the chaff can be also reduced.
ILLUSTRATED GUIDE
- Material push stick
- Mainframe
- Ventilation grid
- Chassis frame
- Debris bag
- Wheel
- Foot chassis
- Feeding funnel
- Handle
- Safety switch
- On/Off switch
ASSEMBLY
Turn the machine over onto its head. Pivot the legs upward, place the supplied wheel axle through the respective openings.
Wheels assembly:
Ⓐ wheel cover
Ⓑ hex nut
Ⓒ wheel
Ⓓ wheel spindle sheath
Ⓔ washer axis
Ⓕ wheels BG
Push the collect box into the undercarriage after pushing the lock button upward.
A = Reset button / Overload protection
REPLACE THE BLADE
Ensure that the shredder is switched off and disconnected from the mains supply. Use work gloves.
Use a cross screwdriver to loosen the six screws plates and cover plates, remove it.
Block the blade disc by putting a screwdriver (A) into one of the holes on the
blade disc. The key (B) turn the blade disc round until it locks onto the
bottom guard plate. Unscrew the hexagonal headed screw by hexagonal wrench (B)
and note the position of the cutting angle of the blade.
After removing the disc is made:
- Cleaning the space under the plate or its replacement
- Turning, grinding and or. replacement blades (procedure see page 15)
When reassembling the reverse procedure to select (Figure 6-7). When mounting, pay particular attention to the correct position of the plates and sufficient tightening of screw joints.
RECOMMENDED ACCESSORIES
|
---|---
HECHT 900106
– safety goggles| HECHT 120153
– cable 20 m
|
HECHT 900102
– ear protection| HECHT 425153
– cable on reel 25 m
| HECHT 900104
– protective gloves
EC DECLARATION OF CONFORMITY
We, the manufacturer of the device and the holder of the documents for issuing
this “EC Declaration of Conformity”: Wesco spool. s r.o., Zap molimen 25/1562,
147 00 Praha 4,
Declare on our own responsibility Machinery Trade name and type: f Electric
knives shredder
Model: Hecht 624 box
The procedure used for the assessment of the conformity: under Directive
2000/14/ EC, Annex VI. as amended by 2005/88/EC
This declaration was issued on the basis of cer-tunicate and measurement
protocols of
TÜV Rheinland Co., Ltd., P.R.C.
TÜV Rheinland LGA Product GmbH, Germany
VCA Headquarters, United Kingdom
This declaration of con- furmety is issued in accordance with EU directives:
2004/108/EC, 2006/42/EC, 2000/14/EC & 2005/88/EC, 97/68/EC & 2010/26/EU
Engine type: GY6000
Validating number: e1197/68SA2010/26268100
The following harmonisednorms are used for guarantee of conformity, together
with the national norms and regulations
ISO 8437, ZEK 01.4-08, EN ISO 3744, ISO 11094, EN 55012, EN 61000-6-1
Guaranteed sound power level
LwA = 111dB(A)
Measured sound power level
LwA = 108,3 dB (A) ; K = 2,64 dB (A) BG
Number of the noise measurement protocol demonstrating compliance with the
requirements of Directive 2000/14/EC: 70.403.10.145.08-06
We confirm hereby that:
- this machine device, defined by mentioned data, is in conformity with basic requirements mentioned in government regulations and technical requirements and is safe for usual operation, contigently for the use determined by manufacturer
- there were taken measures to ensure the conformity of all products introduced to the market with the technical documentation and requirements of the technical regulations
In Prague on : 12.9.2017
Name: ……………………………………
Title: Executive Director: …………………………..
www.hecht.cz
MK-1309018 V.2.1
Distribution and service
HECHT MOTORS s.r.o.
U Monotechnic 131
251 62 Tahoe
www.hecht.cz
www.onlinemashini.bg
References
- HECHT – specialista na zahradu
- HECHT - špecialista na záhradu | HECHT.SK
- Онлайн магазин за машини | Магазин за инструменти | Професионална техника
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>