V I V O STAND-V103 Triple Monitor Desk Mount Instruction Manual
- June 12, 2024
- V I V O
Table of Contents
Triple Monitor Desk Mount
Instruction Manual
SKU: STAND-V103
STAND-V103 Triple Monitor Desk Mount
Scan the QR code with your mobile device or follow the link for helpful videos
and specifications related to this product.https://vivo-
us.com/products/stand-v103
GET IN TOUCH
Monday-Friday from 7:00am-7:00pm CST
| |
---|---|---
help@vivo-us.com| www.vivo-us.com
Chat live with an agent!| 309-278-5303
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT
TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
NOTE: SOME HARDWARE MAY NOT BE USED
TOOLS NEEDED
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
OPTION A: Clamp Installation
Install Upper Clamp (C) to Pole (A) using M6x8mm Screws (S-A) and a Phillips
screwdriver. Assemble Lower Clamp (B) to Upper Clamp (C) using M10x15mm Screws
(S-B) and 5mm Allen Wrench (T-B). Secure the clamp assembly to the desktop be
tightening to the hand bolts on Lower Clamp (C). Install the Pole Cover (D) to
Pole (A).
OPTION B: Existing Grommet Base Installation
Remove adhesive backing from Grommet Pad (L) and place on the bottom of Pole
(A). Install Pole (A) to existing grommet hole using Support Plate (I) with
M10 Bolt (S-F), M10 Washer (S-E) and Lock Washer (S-G). Tighten with Wrench
(T-D). Install the Pole Cover (D) to Pole (A).
OPTION C: Self-Drilled Grommet Base Installation
Drill a 3/8” (10mm) diameter hole through the mounting surface Remove adhesive
backing from Grommet Pad (L) and place on the bottom of Pole (A). Install Pole
(A) to existing grommet hole using Support Plate (I) with M10 Bolt (S-F), M10
Washer (S-E) and Lock Washer (S-G). Tighten with Wrench (T-D). Install the
Pole Cover (D) to Pole (A).
STEP 2
Align Arm Extensions (F) with Arm (E) so that the holes for the wire clips are
facing down. Place Plastic Spacers (H) on top and bottom of Arm Extensions
(F). Assemble Arm Extensions (F) to Arm (E) with M10x47mm Screws (S-C) and
tighten using 6mm Allen Wrench (T-C). Press Joint Covers (G) into place.
STEP 3
Assemble Arm (E) to Pole (A) using M8x10mm Screws (S-D) and 5mm Allen Wrench
(T-B).
STEP 4
OPTION A: Flat Back Monitor
Secure Side VESA Plates (K) to monitors using M4x12mm Thumbscrews (M-A).
Secure Center VESA Plate (J) to monitors using M4x12mm Thumbscrews
(M-A).
OPTION B: Curved Back Monitor
Secure Side VESA Plates (K) to monitors using M4x30mm Screws (M-B) and M4
Spacers (M-C). Secure Center VESA Plate (J) to monitors using M4x30mm Screws
(M-B) and M4 Spacers (M-C).
STEP 5
Assemble side VESA Plates (K) with monitors to Arm Extensions (F). Secure
using Cap Nuts (S-I).
Assemble Center VESA Plate (J) with monitor to
Arm (E). Secure using M4x6mm Screw (S-H).
STEP 6
Remove the plastic covers on Arm Extensions (F) and adjust the tilt using
Wrench (T-D). Adjust the Tilt and rotation of the center monitor by loosening
the set screw on Arm (E) using 3mm Allren Wrench (T-A). Retighten the set
screw. STEP 7
Adjust the Height of Center Monitor:
Using 6mm Allen Wrench (T-C), turn the bolt on Arm (E) counterclockwise
tolower the center monitor, turn the bolt clockwise to raise the center
monitor. Adjust the Height of Side Monitors:
Remove Cap Nut (S-I) from Arm Extensions (F). Turn the screw using
counterclockwise using 3mm Allen Wrench (T-A) to raise the monitor, and
clockwise to lower it. STEP 8
Remove Joint Covers (G) from Arm (E) to adjust the tension using 6mm Allen
Wrench (T-C).
STEP 9
Insert Cable Clips (M) into the undersides of Arm (E) and Arm Extensions (F).
Route cables through Cable Clips (M) and Pole (A).
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer
immediate assistance with rapid response times. If any parts are received
damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
| 309-278-5303| AVG. RESOLUTION TIME
(within office hrs): 5M 4S
---|---|---
| www.vivo-us.com
Chat live with an agent!| VG. RESOLUTION TIME (within office hrs): < 15 M
| help@vivo-us.com| AVG. RESPONSE TIME (within
office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
LAST UPDATED: 06/13/2022
Documents / Resources
| V I
V O STAND-V103 Triple Monitor Desk
Mount
[pdf] Instruction Manual
STAND-V103 Triple Monitor Desk Mount, STAND-V103, Triple Monitor Desk Mount,
Monitor Desk Mount, Desk Mount, Mount
---|---
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Triple Monitor Desk Mount – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>