V I V O DESK-V000KN Vintage Brown Desk Riser Instruction Manual

: June 12, 2024
: V I V O

Table of Contents

V I V O DESK-V000KN Vintage Brown Desk Riser
Product Information
Product Usage Instructions
PACKAGE CONTENTS
TOOLS NEEDED
ASSEMBLY STEPS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

V I V O DESK-V000KN Vintage Brown Desk Riser

V-I-V-O-DESK-V000KN-Vintage-Brown-Desk-Riser-product

Product Information

The Vintage Brown Desk Riser (SKU: DESK-V000KN) is a desk riser that allows users to elevate their workspace from a sitting to a standing position. The product comes with a keyboard tray, stopper,pads, rubber feet, cable clips, and screws. The desk has a weight capacity of 33 lbs (15kg), while the keyboard tray can hold up to 4.4lbs (2kg). The product also features a handle on the right side of the frame and metal brackets for the keyboard tray.

Product Usage Instructions

Apply Pads (D) to the underside of the Keyboard Tray (B). Assemble Stopper (C) to Keyboard Tray (B) using ST4.2x12mm Screws(S-A) and a Phillips screwdriver.
Install Rubber Feet (E) to the bottom of Desk (A). Cut the large shipping tie, but do not squeeze the handle on Desk (A) while cutting the shipping tie.
Raise Desk (A) by lifting the handle on the right side of the frame.
Place Keyboard Tray (B) on the metal brackets on Desk (A).Secure Keyboard Tray (B) to brackets using M5x10mm Screws (S-B) and tighten with a Phillips screwdriver.
Apply Cable Clips (F) to the underside of Desk (A).
If installing a monitor mount, remove the plug from the desktop, then secure the mount using the grommet mounting hardware included with your monitor mount. Keep the monitor and laptop base fully on the desktop. Follow the cable routing instructions to avoid the potential to pinch cables. Leave enough slack in the cable to allow for full range of vertical motion (15 / 38 cm). Raise the desktop slowly to keep items stable.

It is important to note that users should not exceed the weight capacity of the desk, as doing so may result in serious injury. Users should also avoid placing their hands on or near support bars, as moving parts can crush and cut. Pinch points are created during lifting and lowering the work surface, so users should follow the instructions provided to avoid serious personal injury or property damage. If any parts are received damaged or defective, users should contact the manufacturer for assistance.

WARNING
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or inappropriate use.
WARNING CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

V-I-V-O-DESK-V000KN-Vintage-Brown-Desk-Riser-
fig-1

TOOLS NEEDED

Scissors
Phillips Screwdriver

DO NOT EXCEED WEIGHT CAPACITY
Failure to do so may result in serious injury. V-I-V-O-DESK-V000KN-Vintage-
Brown-Desk-Riser-fig-5

WARNING: PINCH POINT DO NOT place hands on or near support bars. Moving parts can crush and cut. Pinch points are created during lifting and lowering the work surface. Failure to follow these instructions may result in serious personal injury.

ASSEMBLY STEPS

STEP 1 Apply Pads (D) to underside of Keyboard Tray (B). Assemble Stopper (C) to Kayboard Tray (B) using ST4.2x12mm Screws (S-A) and a Phillips screwdriver.
STEP 2 Install Rubber Feet (E) to the bottom of Desk (A). Then cut the large shipping tie. NOTE: DO NOT squeeze the handle on Desk (A) while cutting the shipping tie.
STEP 3 Raise Desk (A) by lifting the handle on the right side of the frame.
STEP 4 Place Keyboard Tray (B) on the metal brackets on Desk (A). Secure Keyboard Tray (B) to brackets using M5x10mm Screws (S-B) and tighten with a Phillips screwdriver.
STEP 5 Apply Cable Clips (F) to underside of Desk (A).
STEP 6 If installing a monitor mount, remove the plug from the desktop, then secure the mount using grommet mounting hardware included with your monitor mount.

CAUTION

Keep monitor and laptop base fully on the desktop.
Follow the cable routing instructions to avoid the potential to pinch cables.
Leave enough slack in cable to allow for full range of vertical motion (15” / 38 cm).
Raise desktop slowly to keep items stable.

Failure to follow these instructions may result in property damage and/or personal injury. Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us LAST UPDATED: 09/28/2022 REV2 V-I-V-O-DESK-V000KN-Vintage-
Brown-Desk-Riser-fig-13

Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

309-278-5303 AVG. RESOLUTION TIME (within office hrs): 5M 4S
www.vivo-us.com Chat live with an agent!
help@vivo-us.com AVG. RESPONSE TIME (within office hrs): 1HR 8M – 23% within < 15m – 38% within < 30m – 61% within < 1hr – 83% within < 2hr – 92% within < 3hr