CRYSTORAMA 2245-BF_NOSHADE Sylvan Four Light Chandelier Instruction Manual
- June 12, 2024
- CRYSTORAMA
Table of Contents
CRYSTORAMA 2245-BF_NOSHADE Sylvan Four Light Chandelier
Product Information
The Crystorama lighting fixture model number 2245-BF_NOSHADE has been in the market for 60 years and is designed to be assembled by a licensed electrician. The fixture comes with iron tubes, a center rod, a coupling, a top square ring, a bottom square ring, a light cluster, a loop, and a fabric shade. The fixture is dry rated and requires 4 Candelabra Base Bulbs with a recommended wattage of 40W and a maximum of 60W. LED bulbs are recommended for extended use. The product is known to contain Lead which is known to the state of California to cause cancer and/or birth defects or reproductive harm.
PARTS LIST
DIMENSIONS
WARNING
- All electrical components must be installed by a licensed electrician in accordance with the National Electric Code and the appropriate local electrical codes.
- You will need 4- Candelabra Base Bulb 40 Watts Recommended 60 Watts Max. USE LED BULBS FOR EXTENDED USE This fixture is Dry rated
How to install
-
Place the threaded end of a iron tube into a hole on the bottom square ring. Secure with a finial. Repeat this for the other iron tubes.
-
Remove the long screw from each of the iron tubes. Align the holes on the top square ring with the holes that the long screws were removed from. Tighten each screw into the holes to secure the top square ring and the (4) iron tubes together.
Make sure that the iron tubes are assembled straight relative to the top and bottom ring before tightening the top screws and the bottom finials. -
Slip the center rod along wire and thread into the coupling located on the top of the light cluster.
-
Slip the arm assembly along wire and thread into the center rod.
-
Spread the arms so that the arms are at equal distance from each other.
-
Remove the short screw from each of the holes on the top square ring. Align the holes on the tabs of the arm assembly with the holes on the top square ring and secure together using the short screws that were removed.
-
Slip the loop along wire and thread onto the nipple of arm assembly.
-
Install the fabric shade onto the candle sleeve.(Optional)
-
Install the bulbs(not included) into the socket.
WARNING: This product can expose you to Lead which is known to the state of California to cause cancer and/or birth defects or reproductive harm. For more information go to www.P65Warnings.ca.gov
Part Number
- A. (1)-Mounting hardware
- B. (1)-Canopy W6”xW6”xH3/4” #XRF2240BFCAN6IN
- C. (1)-Collar ring
- D. (1)-Collar loop
- E. (1)-Chain -72”, 4mm thick #XRF2240BFCHA4.0MM
- F. (1)-Loop #XRF2240BFLOOP
- G. (1)-Pipe D1/2”x4-3/8”
- H. (8)-Short screw
- I. (4)-Long screw
- J. (1)-Top square ring W13-5/8”xW13-5/8”xH1/2” #XRF2245BFTOPRING
- K. (4)-Iron tube L12-3/4”xH1/2” #XRF2245BFIRT
- L. (1)-Bottom square ring W15-3/4”xW15-3/4”xH1/2” #XRF2245BFBOTRING
- M. (4)-Bottom finial #XRF2243BFFIN
- N. (4)-Fabric shade W4-1/2”xH5-1/2” #XRF2245SHA5.5IN
- O(A). (4)-Candle sleeve-BF W7/8”xL3-3/8” #XRF2241BFCDL3.375IN
- O(B). (4)-Candle sleeve-WH W7/8”xL3-3/8” #XRF2241WHCDL3.375IN
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>