GLOBAL INDUSTRIAL 800577 Heavy-Duty Electric Adjustable Workbench User Manual

GLOBAL INDUSTRIAL 800577 Heavy-Duty Electric Adjustable Workbench User Manual

Technical Specifications

Soft start/stop
Adjustable leveling studs
4 Memory presets

Caution / Information

Make sure no obstacles are in the desk’s path Make sure the desktop is not touching any walls. Make sure all cords are appropriate length to accommodate the change in height.

WARNING

Pinch Point Keep hands and fingers clear

Keep children away from electric height-adjustable desks, control units and handsets. There is a risk of injury and electric shock

Keep all electrical components away from liquids.

Do not sit or stand on the desk frame. Do not crawl or lie under the desk frame.

Do not place any objects taller than 20· underneath the desk.

Do not open any of the components —the Legs, Control Box, or Switch. There is a danger of electric shock.

This product is designed with a duty cycle of 10%. (2 min. on, 18 min. off)

In the event of a power outage or if the power cord is unplugged, a manual reset may be necessary–see Step 9.

Use/Liability
This height adjustable desk has electric motors and is designed for use in dry work areas only.

The desk height is adjustable so that it can be positioned at the most ergonomically suitable height.

Any other use is at user’s risk.

Under no circumstances does the manufacturer accept warranty claims or liability claims for damage caused from improper use or handling of the desk frame.

Important:
Please read this manual carefully, if this desk is sold, please provide this manual to the buyer.

Parts

Tools required

• 5mm Allen Wrench (Included)

• Phillips Head Screwdriver and or Power Drill

• Tape Measure

• P1 Legs

• P2 Legs

• P5 Cream

• P4 Cross Beam

• P5 Short beam

• P6 Short beam

• P7 Control Box

• P9 Switch

• P9 Motor Cord

• P10 Power Cord

• P11 Foot plate

• P12 Adjusting nut

• P13 Connector part

• P14 Mounting part

Hardware

• Machine Screws M6x10

• Machine Screws M6x16|

• Wood Screws MSx25

• Wood Screws M4x16

• Cable Clips

Assembly Instructions

Plug -the Power Cord(P9) into a llOV outlet

Make sure no obstacles are in the desk’s path. Make sure the desktop is not touching any walls. Make sure all cords are appropriate length to accommodate the change in height. Important You must Reset the desk prior to use.

Reset Procedure: Press and hold the DOWN button on the Switch {P7) until the desk reaches its lowest height. Release the DOWN button. Press and hold the DOWN button again until the LED display reads “RES” or about 10 seconds on non-LED handset models. Release the DOWN button. Press and hold the DOWN button again until the desk lowers a little bit more, slightly rises and stops. Release the DOWN button. Your desk is now ready to use.

To program up to four presets (on some models): Use the up/down buttons to find a desired height, then press “M” ( ·s· on some models) followed by a number 1–4.

Caution: Once a preset button is pushed, the desk will move to the programmed height(see caution box above).

Troubleshooting

If your desk is not functioning properly it may need to be reset Unplug the power cord for 20 seconds. Plug the power cord back in and follow the RESET procedure outlined in Step 11.

If your desk has a handset with an LED readout and it displays “RES” (reset), perform the reset procedure outlined in Step 11.

If the LED readout displays an error message ( “El • — “E 60 • l confirm that all wired connections are  secure(legs to cables, cables to control box). Then perform the reset procedure outlined in Step 11.

If the error message persists after the reset procedure, contact your seller.

If the height between the legs exceeds 1.5 inches, stop the reset procedure contact your seller.

If the handset displays “HOT” , let the base cool down for 20 minutes.

Control Panel Instructions

Rest

When powering on for the 15t time, or if the display shows E =DEEE or EED hold m for 3 seconds until I’El :l shows on the screen. The desk will reset both legs to the lowest position.

Lifting

Press to raise and lower the desk

Memory

Press and then press n– to save the current height to memory

Setup Mode

Pressm for 3 seconds until 5″flashes on the display. Press Magain to enter setup mode.
Use to scroll through the setup options, pressing to select one of the following modes:

Units: Displays height in cm ) redisplays height in inches
Brightness: Low, n NormaI or H High screen brightness
Beep: or
Collision Force: ight, n NormaI orH Heavy collision force detection
set Height: Original height after RESET | Program HHigh & L Low height limits
Serial Number: Scrolls in display window
Demo: (Mode disabled)

Error Codes

overheat   Alert: Let unit cool down
collision / Tit: Eliminate cause of collision, tilt or vibration | Press any key to clear | RESET
Motor Error: Check all cables and connections | Power OFF/ON | RESET
Overload: Remove heavy objects from desktop | Power OFF/ON | RESET
Low Voltage: Power OFF/ON, RESET
High voltage: Power OFF/ON, RESET
Sync Error: Check all cables and connections for both motors | Power OFF/ON | RESET

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>