V I V O DESK-V000K-M2-G-W Standing Desk Converter with Dual Monitor Mount Instruction Manual
- June 12, 2024
- V I V O
Table of Contents
Desk Riser with Dual Monitor Mount
Instruction Manual
SKUS: DESK-V000K-M2/G/W
DESK-V000KN-M2
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product.
https://vivo-us.com/products/desk-v000k-m2
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual and do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly, or inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
TOOLS NEEDED
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING
PINCH POINT
DO NOT place hands on or near support bars. Moving parts can crush and cut.
Pinch points are created during lifting and lowering the worksurface. Failure
to follow these instructions may result in serious personal injury.
CAUTION!
| Keep monitor and laptop base fully on the desktop.
---|---
| Follow the cable routing instructions to avoid the potential to pinch
cables.
| Leave enough slack in cable to allow for full range of vertical motion (15”
/ 38 cm).
| Raise desktop slowly to keep items stable.
Failure to follow these instructions may result in property damage and/or personal injury.
ASSEMBLY STEPS
STEP 1
Apply Pads (D) to the underside of Keyboard Tray (B). Install Stopper (C) on
Keyboard Tray (B) using ST4.2x12mm Screws (S-A) in the pre-drilled holes and a
Phillips screwdriver.
STEP 2
Install Rubber Feet (E) to the bottom of Desk (A). Then cut the large shipping
tie.
NOTE: DO NOT squeeze the handle on Desk (A) while cutting the shipping
tie.
STEP 3
Raise Desk (A) by lifting the handle on the right side of the frame.
STEP 4
Place Keyboard Tray (B) on the metal brackets on Desk (A). Secure Keyboard
Tray (B) to brackets using M5x10mm Screws (S-B) and tighten with a Phillips
screwdriver.
STEP 5
Apply Cable Clips (F) to underside of Desk (A).
STEP 6
Insert Pole Cap (L) into Pole (H).
STEP 7
Remove adhesive backing from Rubber Pads (P) and place them on the underside
of over Grommet Plate (M). Remove plug from Desk (A).
STEP 8
Position Pole (H) with Grommet Plate (M) over the grommet hole of Desk (A),
and install to desktop using Hand Bolt (N) with Support Plate (O). Tighten and
secure.
STEP 9
Slide Pole Cable Clip (J) and Arm (G) onto Pole (H) and secure at the desired
height using 6mm Allen
Wrench (T-A). Attach Arm Cable Clips (K) to Arm (G).
STEP 10
Flat Back Monitor
Install VESA Plates (I) to monitors using Screws (M-A or M-C) and M5 Washers
(M-E).
Curved / Recessed Back Monitor
Install VESA Plate (I) to monitors using Screws (M-B or M-D), M5 Washers (M-E)
and Spacers (M-F).
STEP 11
If needed, adjust tilt joint support using 6mm Allen Wrench (T-A).
STEP 12
Slide the VESA Plates (I) with monitors onto the Arms (G). Secure using the
Knobs (Q) with M3x8mm Screws (S-C).
STEP 13
Route cables through Arm Cable Clips (K) and Pole Cable Clip (J).
STEP 14
Adjust monitor position and rotation as desired. Adjust monitor alignment by
turning Knob (Q) with 6mm Allen Wrench (T-A). Store Allen Wrench (T-A) in the
Pole Clip (J) for future adjustments.
CAUTION: To prevent tipping, please be careful not to extend the arms too far forward or backward.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
309-278-5303
AVG. RESOLUTION TIME (within office hrs): 5M 4S
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within office hrs): < 15 M
help@vivo-us.com
AVG. RESPONSE TIME (within office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- 32" Standing Desk Converter with Dual Monitor Mount – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>