CANOPIA SOPHIA Polycarbonate Door Instruction Manual
- June 12, 2024
- CANOPIA
Table of Contents
CANOPIA SOPHIA Polycarbonate Door Instruction Manual
SAFETY ADVICE
- Itis of utmost importance to assemble all of the parts according to the directions. Do not skip any steps.
- We strongly recommend using work gloves during panel sliding.
- Some parts may have sharp edges. Please be careful when handling components.
- Always wear shoes and safety goggles when working with extruded aluminium.
- If using a step ladder or power tools make sure that you follow the manufacturer’s safety advice.
- Keep children away from the assembly area.
- Do not touch overhead power cables with the aluminium profiles.
- Do not attempt to assemble the product in windy or wet conditions.
- Dispose of all plastic bags. Keep them out of reach of small children.
- Do not climb or stand the roof.
- Do not hang or lay the profiles.
- Do not position your product in an area exposed to excessive winds.
- Do not attempt to assemble this product if you are tired, have taken drugs or alcohol or if you are prone to dizzy spells.
- Make sure there are no hidden pipes or cables in the wall before inserting the pegs.
- This product is designed to be used mainly as a Door Awning.
- Heavy snow load on the roof can make it unsafe to stand below or nearby.
- The wall anchoring kit supplied with this product is suitable for concrete or solidbrick walls. Other wall types need an accordant wall fixation kit
CARE & MAINTENANCE
- When your product needs to be cleaned, use a mild detergent solution and rinse with cold clean water.
- DO NOT use acetone, abrasive cleaners or other special detergents to clean the panels.
- Clean the product once assembly is complete.
TOOLS & EQUIPMENT
-
2 people needed
-
Work gloves
-
Spirit Level
-
Scissors
-
Pencil
-
Electric Drill \ g Penci S| withorilsit 10mm | 13/32″
-
Electric Drill With Drill Bit 8mm | 5/16″
-
Ladder
-
Tape measure
-
Wrench 13 mm/1/2″
-
Allen Key /Hex Key 5mm
-
Cordless Drill Philips Head
BEFORE ASSEMBLY
- Selecting a site: – Choose your site carefully before beginning assembly. – Consider the door’s opening – inside or outside. – The product must be positioned and fixed on a flat level surface.
- This is a multi-part assembly best achieved by two people. Allow at least half a day for the assembly process.
- Take all components & parts out of the packages. Sort the parts and check against the content parts list.
- Parts should be laid out close at hand. Keep all small parts (screws etc.) in a bowl so they do not get lost.
- Please note multi-sided profiles are used in this Door Awning. As a result some holes in the profiles are not used during assembly.
- Please review entire instructions before starting. Carry out the assembly steps in exact order.
- Please consult your local authorities if any permits are required prior to constructing the product.
IMPORTANT!
- During assembly use a soft surface below the parts to avoid scratches and damages.
- You are solely responsible for determining whether the handling, storage, assembly, installation or use of this product is safe and appropriate in any location or for any given application.
- The manufacturer is not responsible for any damages or injury to you, any other person or any property resulting from the improper handling, storage, installation, assembly or use of this product, or the failure to follow the manufacturer’s written instructions regarding the handling, storage, installation, assembly and use of this product.
- This product is intended for normal residential use only. Do not use this product for any application that is not recommended in these instructions or building codes in effect in location where this product will be used. Always take care and use appropriate safety equipment (including eye protection) when assembling or installing this product.
DURING ASSEMBLY
-
During assembly, you will encounter different icons for different products. Please see below for more information:
-
During assembly you will encounter the information icon, please refer to the relevant assembly step for additional comments and assistance.
-
You may use silicone lubricant spray on the frame in order to help you slide the panels into the profiles. Do not spray the panels.
-
Use a rubber mallet if necessary.
-
Make sure you remove covering plastic film from both sides of the panel.
-
All panels with the stamped words “THIS SIDE OUT” must be facing out to create full UV protection. Remove plastic sticker as panels are locked in place.
-
Steps marked with dashed outlines refer to Extensions only.
-
Some of the steps are irrelevant for an assembly of a single product.
-
When assembling a single or an extended product, some parts may be surplus.
-
These 2 icons below indicate if screw’s tightening is required or not
-
Temporary tightening of a few screws may be needed to prevent a profile from sliding out.
-
Tighten all screws once assembly is completed.
CUSTOMER SUPPORT
AUSTRALIA – GREENHOUSES
% 03-9544-6-999
DX info@mazedistribution.com.au
HUNGARY – SLOVAKIA
Q| +420-493-523-53
g servis@garland.cz
NEW ZEALAND
X’ 0800 800 880
g customer.service@palram.co
DENMARK
Q| 075754270
BD<] post@nshnordic.com
SOUTH AFRICA
on1-397-7171
g receptionza@palram.com
CROATIA – SLOVENIA
Q’ 0599-37-057
g info@ms-viscom.com
CZECH REPUBLIC
Q’ 0493-523-523
D<) | servis@garland.cz
FINLAND
@ Neuvonta: 09-6866720
Tuki / Varaosat: 050-3715350
g www.horisontenterprises.fi
tuki@horisontenterprises.fi
POLAND
@ Infolinia: 801-011-929
22-349-93-36
g kontakt@ogrodosfera.pl
CYPRUS
0224-971-13
g alpaco@alpacodomica.com
www.alpacodomica.com
SWITZERLAND
@ 062-287-33-77
D<) info@ritter.ch
Declaration of Performance
According to Construction Products Council Directive UE N°305/2011 and EN
14963:2006
Issue Date 22/01/2021
-
Identification code: Sophia™ 1600/2150, refer to CE label no 060
-
Type: A light transmitting self-supporting solid PMMA roofing structure with upstand made of galvanized steel elements
-
Intended use: open multi-purpose covering
-
Manufacturer: Palram Canopia Ltd. Teradion Industrial Park, M.P Misgav 2017400, P.0.B. 53, Israel
-
Importer and EU representative : PALRAM Applications UK, Unit 40 )3 Industrial Estate Carr Hill,
Doncaster DN4 8DE -
Assessment and verification of constancy of performance: System 3
-
Declared performance: N
Resistance to downward loads: DL 1800
Reaction to fire: B, 51, dO
For mounting and fixing provisions see EN 161532013
Resistance to fire: NPD
Water tightness:
For the rooflight with upstand: Pass
For the sheet material: Pass
Impact resistance:
For the small hard body: Pass
For the large soft body: Pass
Thermal transmittance:
For the rooflight: NPD (not relevant to an open multi purpose cover) Direct
airborne sound insulation: NPD (not relevant to an open multi purpose cover)
Radiation transmittance:
- Light transmittance: Tv – 93 %
- Solar direct transmittance: Te – 81.83 %
- Solar factor: g value – 0.85
Air permeability:
For the rooflight: NPD (not relevant to an open multi purpose cover)
Durability (of the sheet material): AA, Cu1, Ku 0
8. The performance of the product identified in points 1and 2 is in
conformity with the declared performance in point 7.
This declaration of performance is issued, in accordance with Annex ZA.2.2 –
EN 14963:2006,
under the sole responsibility of Palram Canopia Ltd.
ITT reports and Factory Production Control records are available upon request
at www.canopia.com
Signed for and behalf of Palram Canopia Ltd. by: 1A Teradion Industrial
Park, Misgav, ~ 22/01/2021
Documents / Resources
|
CANOPIA SOPHIA Polycarbonate
Door
[pdf] Instruction Manual
705904, 763552409737, 0763552409737, 1005582818, 601471, MV-1, SOPHIA, SOPHIA
Polycarbonate Door, Polycarbonate Door, Door
---|---
References
- Contact Us Archive - Canopia
- Parts Request - Canopia
- Support Archive - Canopia AU
- tex.com
- Inspection Systems for the Electronics Industry – Viscom – Viscom
- Αρχική Σελίδα - Alpaco Domica
- Canopia United Kingdom - Celebrate Outdoor Living
- Contact Us Archive - Canopia
- Parts Request - Canopia UK
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>