CANOPIA 1500 Nancy Door Awning Siding Connector Instruction Manual

: October 30, 2023
: CANOPIA

Table of Contents

TOOLS & EQUIPMENT
SAFETY ADVICE
BEFORE ASSEMBLY
DURING ASSEMBLY
CARE & MAINTENANCE
IMPORTANT ASSEMBLY STEPS
Installation Instruction
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

**CANOPIA 1500 Nancy Door Awning Siding Connector Instruction Manual

**

TOOLS & EQUIPMENT

2 people needed
Work gloves
Spirit Level
Philips head Screwdriver
Electric Drill With Flat Wood Drill Bit 25.4 mm | 1″
Electric Drill With Drill Bit 5 mm | 3/16″ 10 mm | 13/32″
Hammer
Ladder
Pencil
Silicone
Tape measure
Wrench 10 mm | 13/32″ 13 mm | 1/2

HAVE A CONCERN? WE CAN HELP.
Before returning your purchase:

You didn’t find what you were looking for? We can help at
canopia.shop/support

Still can’t find what you are looking for?
Please see next page for local customer care.

WE ARE HERE TO HELP
For general questions: canopia.com/contact-us

NORWAY
SWEDEN
ARGENTINA
GREECE
GREENLAND
ICELAND
ESTONIA
JAPAN
LATVIA
LITHUANIA MAURITIUS
MEXICO
ROMANIA
RUSSIA
TURKEY
UZBEKISTAN
UKRAINE
SWAZILAND
KOREA

+972-4-848-6816 customer.service@palram.com

USA	CANADA	HUNGARY • SLOVAKIA
877-627-8476	[generalsupport@poly-tex.com](mailto:generalsupport@poly-
tex.com)	905-5646007
sales@footprintproducts.com
+420-493-523-523	servis@garland.cz
UNITED KINGDOM • IRELAND	GERMANY	NEW ZEALAND
01302-380775
customer.serviceUK@palram.com
0180-522-8778
customer.serviceDE@palram.com	0800
800 880	customer.service@palram.com
FRANCE • BELGIUM	ISRAEL	DENMARK
+33-169-791-094
customer.serviceFR@palram.com
04-848-6800
customer.service@palram.com	07-575 42
70	post@nshnordic.com
ITALY • NETHERLANDS • PORTUGAL • SPAIN	AUSTRIA • LUXEMBURG • LIECHTENSTEIN

0224-971-13 | alpaco@alpacodomica.com | www.alpacodomica.com Neuvonta: 09-6866720 Tuki / Varaosat: 050-3715350
www.horisontenterprises.fi tuki@horisontenterprises.fi

SAFETY ADVICE

It is of utmost importance to assemble all of the parts according to the directions. Do not skip any steps.
We strongly recommend using work gloves during panel sliding.
Some parts may have sharp edges. Please be careful when handling components.
Always wear shoes and safety goggles when working with extruded aluminium.
If using a step ladder or power tools make sure that you follow the manufacturer’s safety advice.
Keep children away from the assembly area.
Do not touch overhead power cables with the aluminium profiles.
Do not attempt to assemble the product in windy or wet conditions.
Dispose of all plastic bags. Keep them out of reach of small children.
Do not climb or stand the roof.
Do not hang or lay the profiles.
Do not position your product in an area exposed to excessive winds.
Do not attempt to assemble this product if you are tired, have taken drugs or alcohol or if you are prone to dizzy spells.
Make sure there are no hidden pipes or cables in the wall before inserting the pegs.
This product is designed to be used mainly as a Door Awning.
Heavy snow load on the roof can make it unsafe to stand below or nearby.
The wall anchoring kit supplied with this product is suitable for concrete or solidbrick walls. Other wall types need an accordant wall fixation kit.

BEFORE ASSEMBLY

Selecting a site:
- Choose your site carefully before beginning assembly.
- Consider the door’s opening – inside or outside.
- The product must be positioned and fixed on a flat level surface.
This is a multi-part assembly best achieved by two people. Allow at least half a day for the assembly process.
Take all components & parts out of the packages. Sort the parts and check against the content parts list.
Parts should be laid out close at hand. Keep all small parts (screws etc.) in a bowl so they do not get lost.
Please note multi-sided profiles are used in this Door Awning. As a result some holes in the profiles are not used during assembly.
Please review entire instructions before starting. Carry out the assembly steps in exact order.
Please consult your local authorities if any permits are required prior to constructing the product

IMPORTANT

During assembly use a soft surface below the parts to avoid scratches and damages.
You are solely responsible for determining whether the handling, storage, assembly, installation or use of this product is safe and appropriate in any location or for any given application.
The manufacturer is not responsible for any damages or injury to you, any other person or any property resulting from the improper handling, storage, installation, assembly or use of this product, or the failure to follow the manufacturer’s written instructions regarding the handling, storage, installation, assembly and use of this product.
This product is intended for normal residential use only. Do not use this product for any application that is not recommended in these instructions or building codes in effect in location where this product will be used. Always take care and use appropriate safety equipment (including eye protection) when assembling or installing this product.
We recommend checking for restrictions or covenants for building this product in your area. In addition we advise to check if you need to submit any forms or if any permit is required prior to building the product.

DURING ASSEMBLY

During assembly, you will encounter different icons for different products. Please see below for more information:

You may use silicone lubricant spray on the frame in order to help you slide the panels into the profiles. Do not spray the panels.

Use a rubber mallet if necessary

Make sure you remove covering plastic film from both sides of the panel.

All panels with the stamped words “THIS SIDE OUT” must be facing out to create full UV protection. Remove plastic sticker as panels are locked in place

Steps marked with dashed outlines refer to Extensions only. Some of the steps are irrelevant for an assembly of a single product. When assembling a single or an extended product, some parts may be surplus.

These 2 icons below indicate if screw’s tightening is required or not. Temporary tightening of a few screws may be needed to prevent a profile from sliding out.
Tighten all screws once assembly is completed.

CARE & MAINTENANCE

When your product needs to be cleaned, use a mild detergent solution and rinse with cold clean water.
DO NOT use acetone, abrasive cleaners or other special detergents to clean the panels.
Clean the product once assembly is complete.

IMPORTANT ASSEMBLY STEPS

When encountering this information icon during assembly, please refer the relevant assembly step for important additional comments.

Note:
This kit is compatible with most common vinyl wall siding with a pattern that does not protrude over 1” from the wall.

Step 1: Use a suitable tool to determine the location of the wall studs. Mark the locations in the designated mounting space.

Step 3: Drill in the profile slot, in accordance with the location on the wall.the pre-drilled holes and the new holes should be at least 1″ apart. If the pre-drilled holes in the profile are flush with the wall studs’ location, do not add new holes. Mount the product to the wall using these predrilled holes.

Step 5: Remove a 1″ diameter circle from the vinyl wall siding, be careful not to remove it from the wall sheathing or from the wall studs!

Step 9: Please proceed with the installation of the Nancy using its provided assembly instructions, steps 1 through 8. Do not close the end caps, at the back of the product, as per the drawing!