HOPER LAYER 20221126 ZD-01 Foot Bath Massager Instruction Manual

HOPER LAYER 20221126 ZD-01 Foot Bath Massager

ABOUT COMPANY

• Importer: Frank And Andy Trading PTY LTD
• Service Address: 40 Greenwood Street, Burwood, Vic 3125,
• Australia Service Hotline: +61 03 7016 7996/+61406 198 737
• E-mail: Support@hoperlayer.com.au
• www.hoper.com.au

Thank you for your purchase. Please carefully read the manual carefully before, especially the precautions, so as to use this machine correctly. Please keep this manual properly so that you can read it at any time when necessary.

Please use it according to the doctor’s advice for the following people
(Please listen to your doctor’s advice and instructions before using any of the follow­ing conditions.)

• Psychiatric patients
• Implanted pacemaker or artificial organ in vivo
• People with cardiac dysfunction and neurogenic hypertension
•  Patients with uncured cerebral hemorrhage and severe thrombosis
•  Patients with hemorrhagic diseases, septicemia, fever, etc.
•  Women during menstruation or pregnancy
• Those who are blunted or unconscious in response to temperature
• Those with inflammation, trauma or skin burns on the feet
• Children and the mentally handicapped must be used under the supervision of an adult

PRODUCT PARTS

The pictures are for reference only, please refer to the real objects

Disassembly and assembly mode

• Press the support key inward with your index finger, then put it under the support frame with your thumb and lift it up, rotating 90°to parallel to the body (as shown in Figure 21

• Press down on the top of the machine to the state shown in Figure 3, that is, complete the folding

UNPACKING PARTS

REMOTE CONTROLPANEL DIAGRAM

•  : Control the on and off of the whole machine;
•  : Control the switching of health, sleep, comfort and warm foot modes;
•  : Control the increasing of water temperature;
•  : Control the decrease of water temperature;
•  : Timing (cycle! 60 minutes timing, 10 minutes increment;
•  : Control the electric massage on/off; (Youth Version has no massage function!
•  : Control breathing color light on/off;
•   : Control ozone sterilization on/off; (Youth Version has no sterilization/ozone

Attention

• Do not spill water or other liquids on the control panel.
•  Do not press and hold the key too hard to avoid program errors.

INTRODUCTION

After plugging in the power plug and electrifying the machine;

• : After power-on, press “Power” once, the buzzer “beep” for a long time, the display screen shows the actual water temperature, the temperature light and the mode light lights up, the temperature defaults to 42 ·c, heating surfing, and the working time defaults to 60 minutes;

• : After starting up, every time you press “Temperature+”, the setting temperature will increase by 1 C, up to 48 ·c, and the actual water temperature will be displayed on the display screen after 3 s of setting;

• : (9, : After starting up, every time you press “Temperature-“, the setting temperature will decrease by 1 C, and the lowest is 35 C. After setting for 3 s, the display screen will display the actual water temperature;

• : After starting up, press the “Mode Key” once, and the health light will light up, and the temperature will default to 42 C. The buzzer “beep” a long sound, and then press the “Mode Key” to light up the sleep light, and the temperature defaults to 40 C. , buzzer “beep” long sound, (massage flat turn 3 stop 1 ), press “mode key” comfortable light lights up, the temperature defaults to 43 C, buzzer “beep” long sound, (massage flat turn 6 stop 2), press “mode key” warm foot light up, the temperature defaults to 45 C, buzzer “beep” long sound, (massage flat turn 8 stop 3)

• : After starting up, press the “Timing Key” once, and the buzzer beeps to show the remaining time of default timing. Press the “Timing Key” again, and the buzzer beeps to show the remaining minutes, increasing by 10 minutes each time, up to 60 minutes;

• : After starting up, press the “Massage Key” once, the buzzer “beep” long sound, the massage motor works, press the “Massage Key” again, the buzzer “beep” long sound, and the electric massage is closed;

• : After pressing “Start”, the colorful breathing light lights up, press the “breathing light” buzzer “beep” once, and the colorful breathing light turns off; Press the “breathing light” buzzer “beep” again, and the colorful breathing light lights up;

•   : After power on, press “Sterilization/Ozone” once, the buzzer will make a long beep, start working, the working time is 3 minutes; long press
  “Sterilization/Ozone” for 3 seconds, the buzzer ” A long beep of “Di” starts to work, and the working time is 60 minutes; in any state, press the “Di” of the “Sterilization/Ozone” buzzer again to end the work.

REMOTE CONTROLLER

1. Remote controller wakeup: Touch anywhere on the remote control panel, the buzzer will beep for a long time, and the display will display ” “. If the remote control is not used within 5 seconds, the remote control light will be off, and it needs to be woken up again.
2. Remote controller charging: When the power is below 20%, the upper right signal light, the red light flashes once every 2 seconds, as a charging indication, during the charging process, the red light is always on, and when the red light is off, the power is fully charged.
3. Remote controller specifications:
   • Battery capacity: 750mAh
   • Rated voltage: 5V =
   • Charging port: Type-C
   • Rated power: 5W

Attention
Because the added water temperature is too high over 53°C to prevent scalding, the buzzer beeps five times, and the whole machine is in a forced standby state. If it needs to be used again, after the water temperature is as low as the safe temperature of 53 ·c, unplug the power plug and plug it again before reuse.

• If you need to add solid medicine during foot bath, please wrap the medicine in gauze and put it in the medicine box for use, so as to avoid the residue blocking the filter screen and the internal pipeline of the machine and causing machine fault.
• It is strictly forbidden to use the machine without water, which may damage the machine or cause danger!
• It is forbidden to use this machine standing, so as not to damage the machine and cause danger!
• Do not operate the machine with wet hands, and do not use the machine near an open flame.
•  Do not place this machine in wet places such as bathroom or swimming pool.
• When the ambient temperature is below o·c, it is strictly forbidden to store water in the product to avoid freezing the parts.
• If you feel uncomfortable [such as dizziness, headache, etc.). please stop using it.
•  Do not move this machine during use, so as to avoid fire.
•  If the liquid leaks from the machine, the machine cannot be used any more.
• If the machine is found to be malfunctioning or abnormal, stop using it immediately, and consult or repair with our company or its maintenance centers, and do not disassemble and repair it by yourself.
•  If the power cord is damaged, in order to avoid danger, it must be replaced by the manufacturer or its maintenance department or full-time personnel.
• The surface of the machine is hot, and people who are insensitive to heat are forbidden to use it.
• After use, the switch should be turned off and the power plug should be pulled out of the socket.
• During use, please clip the handle into the slots on both sides of the base.]

MAINTENANCE AND STORAGE

• Before cleaning, please make sure that the power switch is turned off and the power plug is unplugged from the socket.
• Please wipe the surface of the product with a soft cloth.
• Dirty places should be cleaned with soft cloth dipped in water or neutral solvent, and then dried with a dry cloth.
• Make sure the power switch is off and the power plug has been pulled out of the socket.
• Keep the product clean and away from high humidity or high temperature and environment with volatile gases.
• If you don’t use the product for a long time, please put it in the packaging box to prevent dust from falling into it.
• Do not unplug the power plug with wet hands.
•  Do not rinse the product with water, or spill water or other liquids into the inside of the product.
• Do not use corrosive detergents such as benzene or diluents to clean products, otherwise the products may fade, and the product structure may be corroded and cracked.
• Do not place the product in a place with direct sunlight or high temperature, so as not to fade the product.

WARM TIPS

• Please do not use this machine in the bathroom or other places with humid air. If it is soaked in water or damp, please do not use it. It should be repaired by our company or distributor.
•  Please use this product in the environment of 0-4□ ·c.
• Please do not store and use this machine near the heater or electric furnace to avoid sunlight.
• This product is for domestic use only, not for commercial use.
• When using it all the year round, please check whether there are the following symptoms:
• Have a burnt smell;
• After touching the wire, sometimes it is powered on and sometimes it is powered off;
• Heating of power cord;
• Other exceptions.

WARNING

• If the above phenomenon occurs, please stop using the product in order to prevent the occurrence of fault and accident.
• Turn off the power switch, unplug the power plug, and contact the dealer or our company where you purchased this product.
• Do not disassemble and repair by yourself.

SPECIAL STATEMENT
This product has undergone a strict water test before leaving the factory. There may be a small amount of water droplets left in the inner barrel of the product, which is a normal phenomenon and does not affect the quality of the product. Please use it with confidence.

WARM TIPS

• The drainage system of this product is designed at the lowest point of the water level, which can basically remove the residual water in the internal pipeline of the machine, but it is recommended to rinse the inside of the cylinder with clean water after use to prevent the breeding of bacteria.
• Before discarding the machine, the battery must be taken out of the machine; When taking out the battery, the machine must be powered off; Batteries should be handled safely. Please support the recycling of rechargeable batteries (lithium ion batteries).
• Battery removal steps:
  1.  Use professional tools to pry open the plastic shell on the non-key side;
  2. Unplug the battery lead terminal plug;
  3.  Take out the battery and dispose of it properly.

DISCARDING ATTEMNTION

Danger

| The battery used in this product is a special rechargeable battery, which cannot be used in other products. Please do not charge the rechargeable battery that has been taken out.

•    Do not throw it into the fire , and make it excessively heated

•    Do not puncture with nail s, gravity impact or decomposition and transformation

•    Do not connect the positive and negative electrodes of the batte r y directly with metal

•    Do not store them with necklaces, hairpins , etc.

•    Please do not charge in high temperature places such as the fire and the hot sun. The above situations can cause fever , fire and rupture.

---|---

Danger

| Please place the removed rechargeable battery out of the reach of infants to prevent it from being swallowed by mistake. In case of swallowing by mistake, please seek medical treatment immediately.

•    When battery liquid leaks. please do not touch the liquid with your bare hands , and treat it according to the following methods.

•    When the battery liquid enters the eyes, there is a danger of blindness. Please do not rub your eyes directly with your hands.

•    Wash them with clear water immediately and seek medical treatment from a doctor. If the battery liquid gets on the body or cloth ing, it may cause skin inflammation or inJury. Please rinse with clear water. If there is still discomfort , seek medical treatmen t immediately.

•    Only when the product is discarded , it can be decomposed. If it is not complied with, it may lead to fire, electric  shock. injury and other accidents . If it needs repair [except  for  electricity replacement ). please consult the store where you originally purchased the product.

SCHEMATIC DIAGRAM OF ELECTRICAL MACHINE

COMMON FAULTS HANDLING

No electricity

| The power plug is not plugged in properly

Function switch not turned on

| Plug in the power plug according to the correct method and turn on the requ red switch. Please contact the seller if none of the above methods can solve the problem.

E1

|

The water temperature is too high to exceed 53·c

|

When the water temperature is cooled to below 53 ‘C , unplug the power plug, and then re-plug the power plug before use.

E2| Temperature sensor fault| Contact the seller for replacement and maintenance

E3

|

The remote control and the machine are not matched

|

At the same time, press “Temperature+” and “Temperature- “, the remote controller displays EE, enters the pair ng mode,

re-energizes the host w thin 5 seconds, and the remote controller and the host buzzer “beep” at the same time, and the remote controller displays PS, and the pairing is successful.

SPECIFICATION PARAMETERS

ci rcul at i ng  heating

Thermal efficiency grade| >60%| Sterilization method| Ozone

WARRANTY CERTIFICATE

Thank you for choosing Hoperlayer products! Dear consumer! When buying the goods, pay attention to the accuracy of filling warranty certificates. Maintenance service is carried out only if a correctly filled warranty certificate is presented. The owners of the products are provided the maintenance service during 12 months from the purchase date. The warranty covers malfunctions that appear during the indemnity period, under condition of normal operation and correct handling. If the product is broken or you experience some difficulties in using it and require any help, you should address to the Hoperlayer registered maintenance shop.
The warranty does not cover:

1.  natural ageing of products;

2. mechanical damage of products;

3. complementary parts, expendable material, packing and accessories;

4.  products which have been installed, operated or handled violating the operating guide requirements;

5.  malfunctions caused by the water quality and scale deposit;

6.  damages caused by using products for profit or by using them in public places, and also, for other purposes which have not been provided for household needs. These products are designed for domestic use only;

7. malfunctions caused by a penetration of foreign items inside goods,
   and also, by heat impact on plastic and other not heat-resistant parts of products;

8. goods that have been under repair somewhere, except in the Hoperlayer registered maintenance shops, including those repaired independently, and those that the owner has attempted to open by themselves;

9. damages caused by the imprudence or negligence, and as a result of a bad handling by the owner;

10. . damages caused by circumstances beyond one’s reasonable control
    ! electric network pressure differences, fire, flooding, accident and other force-majeure circumstances].

    • The maintenance service is provided only in the Hoperlayer registered maintenance shops, and only in cases covered by the present warranty certificate. If there is any problem while using our products, address to one of our registered maintenance shops, or call the Hoperlayer Customer Service.We hope that our products will serve you for a long time, and you will be happy with our service quality.
    • Pis upload related purchase information through www.hoper.com.au to enjoy honorable after-sale service and more benefits!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>