Parklio Remote Control Gate User Manual

Remote control for the Parklio™ Gate
USER MANUAL

Trademarks
ParklioTM is a trademark of Parklio d.o.o.
Other brand and product names are registered trademarks or trademarks of their respective holders.
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, ParklioTM reserves the right to make changes to the products described in this document without notice. ParklioTM does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein.
Thank you for the confidence you have shown us by purchasing our product!
Please read this manual first!
Dear Customers,
We hope that all your expectations of this product will be fulfilled. Every ParklioTM product is manufactured using the latest technologies and has undergone rigorous quality control procedures.
The User Guide will help you use your product quickly and safely.
Read the user manual before installing and using your product.
Always follow the safety instructions.
Keep this user manual at hand for future reference.

User information

• Parking Gate, in addition to valid security, will last for years with just simple care from your side. Even if your automation device meets all the safety standards, this does not exclude the presence of residual risk, i.e. the possibility that hazardous situations may occur due to irresponsible or even improper use. For this reason, we wish to offer some advice regarding the behaviour to be adopted in order to avoid problems.
• Before using the Parklio Gate for the first time, ask the installer to explain the sources of residual risk to you, and take some time to read the instruction manual and user information delivered by the installer.
• Keep the manual for any future doubts and give it to any new owners of the device.
• Your Gate is a machine that faithfully follows your commands; irresponsible and improper use can make it hazardous: do not start a movement of the device if there are people, animals or objects within its radius of action.
•  Children: installed following technical regulations, boom Gate guarantees a high level of safety.
•  However, it is prudent to prevent children from playing near the Gate and to avoid uninten- tional use; never leave the remote control within the reach of children: it is not a toy!
• Anomalies: as soon as the Gate shows any anomalous behaviour, remove the electricity supply and perform manual unblocking. Do not attempt any repairs yourself, but ask your installer: in the meantime, the system can operate as a non-automated device.
• Maintenance: as with all machinery, your automation devices require periodic maintenance so that it may continue to work for as long as possible, and in complete safety. Agree a pe- riodic maintenance plan with your installer; PARKLIO recommends a maintenance plan to be performed every 6 months for normal domestic use, but this period may vary depending on the intensity of use.
•  Any inspection, maintenance or repairs should only be performed by qualified personnel. Even if you think you know how, do not modify the system and the automation device pro- gramming and adjustment parameters: your installer is responsible for this. Final testing, periodic maintenance and any repairs should be documented by those operating, and the documents held by the system owner.
•  Disposal: on completion of the device’s operating life, ensure that disposal is performed by qualified personnel and that the materials are recycled or disposed of following valid local regulations.
•  Important: If your Gate is fitted with a radio control, the function of which appears to dete- riorate over time, or has even ceased to function, this might simply depend on the batteries being run down (depending on the type, this may be from several months to up to two/ three years). Before contacting your installer, try replacing the battery with the battery from another, working transmitter: if this was the cause of the problem, then simply replace the battery with another of the same type.
•  Are you satisfied? Should you wish to add another automation device to your home, contact the same installer and ask for a PARKLIO product: we guarantee you the most advanced products on the market and maximum compatibility with existing  automation devices.
• Thank you for having read these recommendations, and for any present or future needs, we ask you to contact your installer in full confidence.

Gate Receiver

The transmitter allows a very high degree of safety for the remote control of the access, thanks to 144-bit processes using multi-level encryption.
For a correct understanding of the following instruction are defined 2.1. Outputs
The receiver has 2 outputs open collector type: the control unit configuration in which it is installed, determines the function associated with each output.
2.2. Receive a code
If a received code is stored with the P1 button, the LED 1 lights and activates the output No. 1 for all the duration of the transmission (it is the same for output 2).
If a received code is not memorised both LEDs light up briefly; if the radio transmission continues, the flashing is repeated at intervals of about 1 “.
2.3. Alarm notifications
MEMORY FULL If trying to memorise a code the two LEDs flash quickly for 4 “ it means that the memory is full and the code cannot be stored. MEMORY DAMAGED If the two LEDs flash quickly without stopping means that the memory is faulty: the receiver cannot work.
2.4. Resetting the memory
Press and hold the two buttons P1 and P2 for 4”: 5 short flashes contemporaries of the two LEDs indicate the complete resetting.
2.5. Deleting a code

1. Locate the RX output activated by the button of the transmitter that is being deleted.
2.  Press the button (P1 or P2) associated with it, keeping it held for 4”: at the be- ginning the LED lights are fixed, and then start to flash quickly.
3.  Release the button: The LED continues to flash quickly (for 4”).
4.  Activate the button of the transmitter to delete: the cancellation is signalled by the LED that lights for 1 “. If the code is not in the memory an error message will be indicated by faster flashes.
5.  To delete any other code return to step 1.

2.6. Storing of a transmitter
NOTE: the first installation it is advised to do a complete deletion of the memory before beginning to  storecodes.

1. Press the P1 button if you want to store button of the transmitter associated with the output 1 (opening of the gate) of the receiver, or the P2 button for out- put 2 (closing the gate). Note that the storing procedure is the same). When you release the button, the corresponding LED flashes 4 times slowly
2.  During this time, press the button of the transmitter you want to store
3. A prolonged power of LED (1“) indicates that it is stored in memory, while few quick flashes indicate that the button of the transmitter is already stored. The button of the transmitter cannot be stored on both outputs of the radio.
4. The LED continues with another 4 slow flashes waiting for other storages (re- turn to step 2). If during this time the other button is pressed, the storage on the other RX output will turn ON; if other codes are not transmitted the receiv- er leaves the storage phase.

 Remote control

3.1. Buttons functions
The buttons do not have predetermined function and they can be memorised in any receiver channel
3.2. Inserting a code
When the receiver is powered press the channel button where the transmitter will be memorised. When the button is released the relative led will blink slowly 3 times, during this period press the button of the remote control in which the code is to be stored. A long blink indicates that storage has been successful, while 3 consecutive fast blinks indicate that the code of the remote control has already been stored in one channel. The led will emit another 3 slow blinks while waiting for other storage procedures. If no other codes are transmitted in this time, the receiver exits from the programming phase. It is impossible to store the same code on both channels; each code is associated with just one channel.
3.3. Changing the battery
To change the battery remove the two screws with a screwdriver on the transmitter back (FIG. 2). Pay attention to the battery polarity marked on the battery holder 3.4. Transmitter copy
This transmitter is able to copy the code from another fixed code transmitter.
Be careful when copying, this procedure must be done by an advised person and with a good battery, otherwise the copy will not work.
Follow these steps to copy a remote control:

• On the COPY transmitter push the button to memorise the code together with the opposite button (A with B, or C with D).
• The LED blinks for 5 seconds, after it becomes fixed
• Hold the button where you want to memorise the code and release the other
• The LED sends out 3 long blinks
• In the meantime place the ORIGINAL transmitter in front of the COPY (FIG. 1) and push the ORIGINAL transmitter button that will be copied
• The LED sends out short flashes waiting a code to copy
• Now pay attention to the COPY transmitter LED: – If the LED turns on for 1 sec   ond and after turns off the copy is done. Now release all buttons.. It is strongly recommended to check that the code is recognised by the receiver, oth- erwise repeat all steps. – If the LED continues to send out short blinks, it means that no codes are received, so be sure to push the ORIGINAL transmitter button or move the transmitter to maximise the signal coupling. However if it does not copy change the battery of the ORIGINAL transmitter – If the LED is still on, the copy is failed, please retry. – If the LED send out fast blinks and after it still fixed, it means that the battery has not enough energy to perform the copy

Disposal

This product may only be uninstalled by qualified technical personnel following suitable procedures for removing the product correctly and safely. This product consists of numerous different materials. Some of these materials may be recycled, while others must be disposed of correctly at the specific recycling or waste management facilities indicated by local legislation applicable for this category of product. Do not dispose of this product as domestic refuse. Observe local legislation for differentiated refuse collection, or hand the product over to the vendor when purchasing an equivalent new product. Local legislation may envisage severe fines for the incorrect disposal of this product. Warning! Some parts of this product may contain substances that are harmful to the environment or dangerous and which may cause damage to the environment or health risks if disposed incorrectly.

Safety warnings

This section contains safety instructions that will help to protect you from risk of injury or property damage. Failure to follow these instructions will invalidate all warranties.

• Do not use the barrier, if you have not read and understood the operating instruc- tions before.
• Before first use of the barrier, make sure that all the parts listed in these instruc- tions are inside of the original packaging.
• Only plugs, batteries, chargers, spare parts and power supplies, supplied by the manufacturer of the barrier should be used. Use of non-manufacturer provided parts may affect the loss of warranty.
• Ignoring usage instructions, improper installation and use of the barrier may re- sult in damage to the barrier or injuries to the user. Instructions should always be at hand.
• Never expose the inner workings to water.
• The device must be exclusively installed on a hard, flat concrete floor.
• The device and external supply must be disconnected from power supply during installation, maintenance, cleaning and repairs.
• Leave the barrier repairs to a specialist. Improper repairs may lead to an accident or a malfunction in the unit.
• Please charge the battery to full capacity before first use.
• Only charge the battery pack with the provided power adapter.
• The battery pack is fragile, please handle it with care. Do not expose the battery to direct heat.
• The battery pack is intended to be used only with Parklio products, use with other products is not recommended. Parklio is not responsible for any damage caused to the equipment or the battery pack when used incorrectly.
• Make sure to close the power input plug of the battery pack before use to seal the port from water ingress.
• The warranty does not cover consumable parts of the device, colour fading and chipping, increased noise as a result of ageing of the device and other aesthetic effects that do not affect its functionality or safety. Never use chemical solvents on the product as it may cause an explosion.
• Strictly follow the instructions for proper installation and connection to the electrical network.
• The installer must provide a device (e.g. magnetothermic switch) ensuring the omnipolar sectioning of the equipment from the power supply. The standards require a separation of the contacts of at least 3 mm in each pole (EN 60335-1).
• Installation requires mechanical and electrical skills, therefore it shall be carried out by qualified personnel only, who can issue the Compliance Certificate concerning the whole installation.
•  The upstream electric system shall comply with the laws and rules in force.
• Do not install the product in explosive environments and atmospheres, the presence of inflammable gases or fumes is a serious safety hazard.

PARKLIO (PARKLIO D.O.O.) HAS THE RIGHT TO MODIFY THE DEVICE WITHOUT PREVIOUS NOTICE. PARKLIO (PARKLIO D.O.O.) DECLINES ANY RESPONSIBILITY FOR DAMAGE OR INJURY TO PEOPLE OR THINGS CAUSED BY IMPROPER USE OR WRONG INSTALLATION. THE APPLIANCE HAS BEEN ESTABLISHED ACCORDING TO ALL VALUENT SAFETY CRITERIA AND STANDARDS. HOWEVER, WE RECOMMEND THAT WITHOUT THE NEEDED HELP AND SUPERVISION, CHILDREN, A PERSON OF DISABLED PHYSICAL, MOTOR OR PERSONAL EQUALITY AND RELATED PEOPLE WITHOUT PREVIOUS EXPERIENCE OR KNOWLEDGE DO NOT USE THE BARRIER. EXCEPTION IS THE DEVICE USAGE UNDER ADEQUATE SUPERVISION, IF THEY HAVE RECEIVED SAFETY INSTRUCTIONS AND TRAINING, OR IF THEY ARE INFORMED ABOUT THE DANGER CAUSED BY IMPROPER USAGE. THE SAME RECOMMENDATION IS FOR JUVENILES AND THEIR USAGE OF THE DEVICE. DO NOT ALLOW CHILDREN TO PLAY WITH THE DEVICE. DO NOT LET CHILDREN CLEAN THE DEVICE, USE IT, NOR MAINTAIN IT, WITHOUT ADEQUATE SUPERVISION.

Documents / Resources

| Parklio Remote Control Gate [pdf] User Manual
Remote Control Gate, Remote Control, Gate
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>