V I V O STAND-RACE1A Racing Steering Wheel Stand Instruction Manual

V I V O STAND-RACE1A Racing Steering Wheel Stand

Product Information: Racing Steering Wheel Stand

The Racing Steering Wheel Stand is a gaming accessory designed to provide a realistic racing experience. The stand is made of durable materials, can support up to 44lbs (20kg), and comes with various components such as a shifter support bracket, cable clips, and footplates. The stand can be adjusted to the user’s preferred angle, height, and position for an optimal gaming experience.

Product Usage Instructions

Before assembling and using the Racing Steering Wheel Stand, please read the following instructions carefully.

Package Contents

• A (x1) Stand
• B (x1) Upright Support Plate
• C (x4) Foot
• D (x1) Shifter Support Bracket
• E (x1) Shifter Plate
• F (x2) Cable Clip
• G (x6) Ziptie
• S-A (x4) M8x16mm Screw
• S-B (x4) M6x12mm Screw
• T-A (x1) 5mm Allen Wrench

WARNING! This product contains small parts and is not suitable for children under 3 years. Adult supervision is required.

WARNING! Do not exceed weight capacity. Failure to do so may result in serious injury.

Assembly Steps

1. Screw Feet (C) into the bottom of Stand (A).
2. Loosen the knobs on the middle of the post on Stand (A), then extend the post. Remove the two knobs locking the post in the folded position. Raise the post, then install the Upright Support Plate (B) to the base and post using M8x16mm Screws (S-A) and the previously removed knobs. Tighten screws with 5mm Allen Wrench (T-A).
3. Tilt the wheel plate on Stand (A) up to the desired angle, then insert M8x16mm Screws (S-A) to secure the tilt angle. Tighten with 5mm Allen Wrench (T-A).
4. Remove the knobs from the foot plate in Stand (A). Remove the screws using 5mm Allen wrench (T-A), move the foot plate to the desired position (1-5), then reinstall the screws.
5. Adjust the foot plate on Stand (A) to the desired angle and reinsert the previously removed knobs.
6. Adjust the post on Stand (A) to the desired height, then tighten the knobs to secure the height.
7. Install Shifter Support Bracket (D) to the left or right side of the wheel support plate on Stand (A) using M6x12mm Screws (S-B). Tighten with 5mm Allen Wrench (T-A).
8. Mount Shifter Plate (E) to Shifter Support Bracket (D) using M6x12mm Screws (S-B) and tighten with 5mm Allen Wrench (T-A). Shifter Plate (E) may be installed to the close or far position depending on user preference.
9. Attach Cable Clips (F) to the post on Stand (A) for cable management.
10. FOLDING INSTRUCTIONS: Remove the lower two knobs from the Upright Support Plate (B) and gently fold the post down. Loosen the knobs on the middle of the post to extend for clearance if needed. Reinsert the previously removed knobs into the sides to lock the post in the folded position.

If any parts are received damaged or defective, please contact the support team at help@vivo-us.com or call 309-278-5303 for assistance.

SKU: STAND-RACE1A
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product.
https://vivo-us.com/products/stand-race1a

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

• help@vivo-us.com
• www.vivo-us.com Chat live with an agent!
• 309-278-5303

WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.

ASSEMBLY STEPS

• STEP 1
  Screw Feet (C) into bottom of Stand (A).
  

• STEP 2
  Loosen the knobs on the middle of the post on Stand (A), then extend the post. Remove the two knobs locking the post in the folded position. Raise the post, then install the Upright Support Plate (B) to the base and post using M8x16mm Screws (S-A) and the previously removed knobs. Tighten screws with 5mm Allen Wrench (T-A).
  

• STEP 3
  Tilt the wheel plate on Stand (A) up to the desired angle, then insert M8x16mm Screws (S-A) to secure the tilt angle. Tighten with 5mm Allen Wrench (T-A).
  

• STEP 4
  Remove the knobs from the foot plate in Stand (A). Remove the screws using 5mm Allen wrench (T-A), move the foot plate to the desired position (1-5), then reinstall the screws.
  

• STEP 5
  Adjust the foot plate on Stand (A) to the desired angle and reinsert the previously removed knobs.
  

• STEP 6
  Adjust the post on Stand (A) to the desired height, then tighten the knobs to secure the height.
  

• STEP 7
  Install Shifter Support Bracket (D) to the left or right side of the wheel support plate on Stand (A) using M6x12mm Screws (S-B). Tighten with 5mm Allen Wrench (T-A).
  

• STEP 8
  Mount Shifter Plate (E) to Shifter Support Bracket (D) using M6x12mm Screws (S-B) and tighten with 5mm Allen Wrench (T-A). Shifter Plate (E) may be installed to the close or far position depending on user preference.
  

• STEP 9
  Attach Cable Clips (F) to the post on Stand (A) for cable management.
  

• STEP 10
  FOLDING INSTRUCTIONS
  Remove the lower two knobs from the Upright Support Plate (B) and gently fold the post down. Loosen the knobs on the middle of the post to extend for clearance if needed. Reinsert the previously removed knobs into the sides to lock the post in the folded position.

Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us

LAST UPDATED: 01/28/2022 REV3

Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

• 309-278-5303
  AVG. RESOLUTION TIME (within office hrs): 5M 4S

• www.vivo-us.com
  Chat live with an agent!
  AVG. RESOLUTION TIME (within office hrs): < 15 M

• help@vivo-us.com
  AVG. RESPONSE TIME (within office hrs): 1HR 8M

  • 23% within < 15m
  • 38% within < 30m
  • 61% within < 1hr
  • 83% within < 2hr
  • 92% within < 3hr

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

References

• Register a .US.COM domain today!
• VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
• Racing Steering Wheel Stand – VIVO - desk solutions, screen mounting, and more

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>