BRESSER 8855500 JUNIOR Microscope with Magnification 40x-2000x Instruction Manual
- October 30, 2023
- BRESSER
Table of Contents
Art. No. 8855500
Microscope with Magnification 40x-2000x
Instruction Manual
8855500 JUNIOR Microscope with Magnification 40x-2000x
MANUAL DOWNLOAD:
SERVICE AND WARRANTY:
MICROSCOPE GUIDE:
MICROSCOPE FAQ:
EXPERIMENTS:
WARNINGS! Not suitable
for children under three years. CHOKING HARZARD – small parts. PUNCTURING
HAZARD – functional sharp points! LACERATING HAZARD – functional sharp edges!
Keep instructions and packaging as they contain important information.
Operating Instructions
WARNING! Not for
children under three years. Choking hazard – small parts. Contains functional
sharp edges and points!
ATTENTION: Only suitable for children of at least 8 years of age.
Instructions for parents or other responsible persons are enclosed and must be
followed. Keep packaging as it contains important information.
General Warnings
- Choking hazard — This product contains small parts that could be swallowed by children. This poses a choking hazard.
- Risk of electric shock — This device contains electronic components that operate via a power source (batteries). Only use the device as described in the manual, otherwise you run the risk of an electric shock.
- Risk of fire/explosion — Do not expose the device to high temperatures. Use only the recommended batteries. Do not short-circuit the device or batteries, or throw them into a fire. Excessive heat or improper handling could trigger a short-circuit, a fire or an explosion.
- Risk of chemical burn — Make sure you insert the batteries correctly. Empty or damaged batteries could cause burns if they come into contact with the skin. If necessary, wear adequate gloves for protection.
- Leaking battery acid can lead to chemical burns. Avoid contact of battery acid with skin, eyes and mucous membranes. In the event of contact, rinse the affected region immediately with a plenty of water and seek medical attention.
- Use only the recommended batteries. Always replace weak or empty batteries with a new, complete set of batteries at full capacity. Do not use batteries from different brands or with different capacities. Remove the batteries from the unit if itis not to be used for a long period of time, or if the batteries are empty!
- Never recharge normal, non-rechargeable batteries. This could lead to explosion during the charging process.
- Rechargeable batteries are only to be charged under adult supervision.
- Rechargeable batteries are to be removed from the toy before being charged.
- The terminals must not be short-circuited.
- Do not disassemble the device. In the event of a defect, please contact your dealer. The dealer will contact the Service Centre and can send the device in to be repaired, if necessary.
- Tools with sharp edges are often used when working with this device. Because there is a risk of injury from such tools, store this device and all tools and accessories in a location that is out of the reach of children.
- Keep instructions and packaging as they contain important information.
- The chemicals and liquids provided should be kept out of reach of children. Do not drink the chemicals! Hands should be washed thoroughly under running water after use. In case of accidental contact with the eyes or mouth rinse with water. Seek medical treatment for ailments arising from contact with the chemical substances and take the chemicals with you to the doctor.
Check the Power supply for damage to the cord, plug, enclosure or other parts
on a regular basis before use. Do not use until the damage has been repaired.
The toy is not intended for children under three years. The toy must only be
used with the recommended power supply. The power supply is not a toy.
The toy is not to be connected to more than the recommended number of power
supplies.
TIPS on cleaning
Remove the device from it’s energy source before cleaning (remove plug from
socket / remove batteries).
Clean the exterior of device with a dry cloth. Do not use cleaning fluids so
as to avoid causing damage to electronic components.
Toys liable to be cleaned with liquid are to be disconnected from the power
supply before cleaning.
Clean the lens (objective and eyepiece) only with the cloth supplied or some
other soft lintfree cloth (e.g. micro-fibre). Do not use excessive pressure –
this may scratch the lens.
DISPOSAL
Dispose of the packaging material/s as legally required. Consult the local
authority on the matter if necessary.
Do not dispose of electrical equipment in your ordinary refuse. The European
guideline 2012/19/EU on Electronic and Electrical Equipment Waste and relevant
laws applying to it require such used equipment to be separately collected and
recycled in an environment-friendly manner.
Empty batteries and accumulators must be disposed of separately. Information
on disposing of all such equipment made after 01 June 2006 can be obtained
from your local authority.
In accordance with the regulations concerning batteries and rechargeable
batteries, disposing of them in the normal household waste is explicitly
forbidden. Please pay attention to dispose of your used batteries as required
by law – at a local collection point or in the retail market (a disposal in
domestic waste violates the Battery Directive).
Batteries that contain toxins are marked with a sign and a chemical symbol.
„Cd“ = cadmium, „Hg“ = mercury, „Pb“ = lead.
- battery contains cadmium
- battery contains mercury
- battery contains lead
EC Declaration of Conformity
** Bresser GmbH has issued a „Declaration of Conformity“ in accordance with
applicable guidelines and corresponding standards.
The full text of the EU declaration of conformity is available at the
following internet address:
www.bresser.de/download/8855500/CE/8855500_CE.pdf
UKCA Declaration of Conformity
Bresser GmbH has issued a „Declaration of Conformity“ in accordance with
applicable guidelines and corresponding standards.
The full text of the UKCA declaration of conformity is available at the
following internet address:
www.bresser.de/download/8855500/UKCA/8855500_UKCA.pdf
Bresser UK Ltd.** • Suite 3G, Eden House, Enterprise Way, Edenbridge, Kent
TN8 6HF, Great Britain
Here are the parts of your microscope
1 10x WF Eyepiece
2 25x WF Eyepiece
3 2x Barlow Lens
4 Eyepiece supports
5 Microscope Head with locking screw
6 Objective Nosepiece
7 Objective
8 Clips
9 Microscope Stage| 10 LED Illumination (transmitted light)
11 Microscope Base
12 Selection switch for Illumination
13 Dimmer for Illumination
14 Battery compartment
15 Focus knob
16 Color Filter wheel
17 LED Illumination (reflected light)
18 Slides, Cover Sips and Prepared Specimens plastic box| 19 Specimens: a)
Yeast, b) Sea Salt, c) Brine Shrimp Eggs (Artemia). d) Empty
Bottle
20 Specimen slicer
21 Magnifier box
22 Tweezers
23 Dissecting needle
24 Dissecting knife
25 Pipette
26 Container
27 Smartphone holder
---|---|---
How do I use my microscope?
Before you assemble your microscope, make sure that the table, desk or
whatever surface that you want to place it on is stable, and does not wobble.
How do I operate the electric LED illumination? In the base of the
microscope there is a battery compartment (14). Loosen the screw at the
battery compartment cover with a small Philips screwdriver and remove the
cover.
Place the batteries in the compartment so that the flat minus poles (-) press
against the spring terminal and the plus poles (+) are touching the flat
contact sheets. Close the battery compartment with the cover and turn the
microscope around again.
The first lamp shines onto the specimen from below and the second from above.
(The thing that you want to observe with the microscope is called the object
or specimen, by the way.) You can use each lamp on its own. There is a
selection switch for this (12). It has two numbers: I and II. If you select
the … I, the light only comes from below (transmitted light).
II, the light only comes from above (reflected light).
For transparent objects (transmitted-light objects), number I is best. In
order to observe firm, non-transparent objects (direct-light objects), select
number II.
With the dimmer (13) you can adjust the brightness of the illumination.
When do I use the color filters?
The color filter wheel (16) is located below the microscope stage (9). They
help you when you are observing very bright or clear specimens. Here, you can
choose from various colors. This helps you better recognize the components of
colorless or transparent objects (e.g. grains of starch, protozoa).
How do I adjust my microscope correctly?
First, loosen the screw (5) and turn the microscope head into a comfortable
viewing position. Each observation starts with the lowest magnification.
Adjust the microscope stage (9) so that it goes all the way down to the lowest
position, using the focus knob (15). Then, turn the objective nosepiece (6)
until it clicks into place at the lowest magnification(objective 4x).
Note: Before you change the objective setting, always move the microscope
stage (9) to its lowest position. This way, you can avoid causing any damage!
Now, insert the 10x eye- piece (1) into the Barlow lens (3). Make sure that
the Barlow lens is placed all the way into the eyepiece supports (4) and is
not pulled out.
How do I observe the specimen?
After you have assembled the microscope with the adequate illumination and
adjusted it correctly, the following basic rules are to be observed:
Start with a simple observation at the lowest magnification. This way, it is
easier to position the object in the middle (centering) and make the image
sharp (focusing).
The higher the magnification, the more light you will require for a good image
quality. Now place the prepared specimen (18) directly under the objective on
the microscope stage. The object should be located directly over the
illumination (10).
In the next step, take a look through the eyepiece (1) and carefully turn the
focus knob (15) until the image appears clear and sharp.
Now you can select a higher magnification by slowly removing the Barlow lens
(3) from the eyepiece support (4). When the Barlow lens is almost completely
pulled out, the magnification can be increased to almost double.
If you would like an even higher level of magnification, insert the 25x
eyepiece (2) and turn the objective nosepiece (6) to a higher setting (10x or
40x).
Important tip:
The highest magnification is not always the best for every specimen!
Note:
Each time the magnification changes (eyepiece or objective change, pulling out
the Barlow lens), the image sharpness must be readjusted with the focus knob
(15). When doing this, make sure to be careful. If you move the microscope
stage too quickly, the objective and the slide could come into contact and
become damaged!
Which light for which specimen?
With this unit, a reflected light and transmitted light microscope, you can
observe transparent, semi-transparent as well as non-transparent objects.
The image of the given object of observation is “transported” through the
light. As a result, only the correct light will allow you to see something!
If you are observing non-transparent (opaque) objects (e.g. small animals,
plant components, stones, coins, etc.) with this microscope, the light falls
on the object that is being observed. From there, the light is reflected back
and passes through the objective and eyepiece (where it gets magnified) into
the eye. This is reflected light microscopy.
For transparent objections (e.g. protozoa), on the other hand, the light
shines from below, through the opening in the microscope stage and then
through the object.
The light travels further through the objective and eyepiece, where it is also
magnified, and finally goes into the eye. This is transmitted-light
microscopy.
Many microorganisms in water, many plan components and the smallest animal
parts are already transparent in nature. Others have to be prepared. We may
make them transparent through a treatment or penetration with the right
materials (media), or by taking the thinnest slices from them (using our hand
or a specimen slicer), and then examine them. You can read more about this in
the following sections.
How do I make thin specimen slices?
Only do this with the supervision of your parents or another adult.
As I already pointed out, the thinnest slices possible are taken from an
object. In order to get the best results, we need some wax or paraffin. It is
best if you get a candle. Place the wax in a pot and heat it carefully over a
low burner. Now, dip the object in the liquid wax a few times. Then, let the
wax get hard. Using the Specimen slicer (20) or a knife/scalpel, cut the
smallest slices from the object that is covered with wax. These slices are to
be laid on a slide and covered with a cover slip.
How do I make my own specimens?
Take the object that you want to observe and place it on a glass slide (18).
Then, add a few drops of distilled water on the object using a pipette. Now,
place a cover slip vertically at the edge of the drop of water, so that the
water runs along the edge of the cover slip. Then, slowly lower the cover slip
over the water drops.
Experiments
Use the following web link to find interesting experiments you can try out.
How do you hatch brine shrimp? How to make salt crystals and much more.
http://www.bresser.de/downloads
Troubleshooting
| Error | Solution |
|---|---|
| No recognizable image | • Turn on light |
• Readjust focus
Make sure your microscope has a long service life.
Clean the lens (objective and eyepiece) only with the cloth supplied or some
other soft lintfree cloth (e.g.microfibre). Do not press hard as this might
scratch the lens.
Ask your parents to help if your microscope is really very dirty. The cleaning
cloth should be moistened with cleaning fluid and the lens wiped clean using
little pressure.
Make sure your microscope is always protected against dust and dirt. After use
leave it in a warm room to dry off. Then install the dust caps and keep it in
the case provided.
Smartphone holder
Open the flexible holder and put your smartphone in it. Close the cradle and
make sure your phone is properly seated. The camera must be positioned exactly
above the eyepiece. Open the locking clip on the back of the holder and fit
the eyepiece view exactly onto your smartphone camera. Now retighten the
locking clip and attach the smartphone holder to the eyepiece of your
microscope. Now start the camera app. If the image is not yet centered on your
display, loosen the locking clip slightly and readjust. It may be necessary to
use the zoom function to fill the image on the display. A slight shading at
the edges is possible. Remove the smartphone from the cradle after use!
NOTE:
Make sure that the smartphone cannot slip off the cradle. Bresser GmbH accepts
no liability for damage caused by a dropped smartphone!
Warranty & Service
The regular warranty period is 2 years and begins on the day of purchase. To
benefit from an extended voluntary warranty period as stated on the gift box,
registration on our website is required.
You can consult the full warranty terms as well as information on extending
the warranty period and details of our services at
www.bresser.de/warranty_terms.
Contact
Bresser GmbH
Gutenbergstraße 2
46414 Rhede · Germany
www.bresser.de| Bresser UK Ltd.
Suite 3G, Eden House
Enterprise Way, Edenbridge,
Kent TN8 6HF, Great Britain
---|---
@BresserEurope
Errors and technical changes reserved.
References
- konsoleH :: Login
- Bresser | Startseite | Expand Your Horizon mit BRESSER
- index · powered by h5ai 0.26.1 (http://larsjung.de/h5ai/)
- Bresser | Downloads | Expand Your Horizon
- Bresser | FAQ | Expand Your Horizon
- bresser.de/garantiebedingungen
- Bresser | Ratgeber | Expand Your Horizon
- Bresser | BRESSER JUNIOR Mikroskop mit einer Vergrößerung von 40x-2000x | Expand Your Horizon
- bresser.de/warranty_terms
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>