POWER-LITE WBB-38W-CC Wide Body LED Batten Installation Guide
- October 30, 2023
- POWER-LITE
Table of Contents
POWER-LITE WBB-38W-CC Wide Body LED Batten
Product Information
The product is an LED Batten Wide Body light fixture that can be installed on a surface or suspended from the ceiling. It has a splicing power of less than 2000W and a detection area of 150 degrees with a 4-7 meter distance. The product comes with instructions for specific functions, which can be found in the actual model. The product includes a set of safety instructions that must be followed for correct function and safety.
Product Usage Instructions
Before starting any installation, switch off the power supply and read the instructions carefully. Check that you have all the tools and accessories necessary to complete the installation correctly. The light source contained in this luminaire should only be replaced by the manufacturer or a qualified person.
Surface Mounted Installation
- Turn off power supply.
- Choose a location for the fixture and mark the position of the holes.
- Drill holes in the marked positions.
- Connect the wires: L (switched), N (neutral), and E (earth).
- Secure the fixture to the surface using screws.
- Switch on the power supply.
Suspended Installation
- Turn off power supply.
- Choose a location for the fixture and mark the position of the holes.
- Drill holes in the marked positions.
- Connect the wires: L (switched), N (neutral), and E (earth).
- Adjust the length of the suspension wire as required.
- Secure the fixture to the ceiling using screws and suspension wires.
- Switch on the power supply.
Warning: Switch on the power supply only after completing the installation and examining the circuit.
If you encounter any issues during installation or usage, please contact our customer service through our website or email.
Splicing installation (Surface mounted / Suspended installation)
Splicing wire connection
**Functions Instruction (For specific
function, please refer to actual model)
Sensor**
Detection area: 150 degree wide detective beam angle with 4-7 meters distance.
Daylight & x Microwave Sensor
Detection area
Detection area can be reduced by selecting the combination on the DIP switches
to fit precisely each application.
- Notice 1 : The test is based on a height of 3m. the radius is the ground detect distance. which can be selected through the slide switch
- Notice 2: The detective range is measured by human body whose stature is around 1.6-1.7M with medium sire and traveling speed is around 1.0-1.SM per second. If the stature, bodily form and traveling speed are changed. then the detective range will be changed accordingly.
- Notice 3: Test result will be highly influenced by test environment. titer more open environment, the closer detect distance; the narrower environment, the longer detect distance. The detector may do self-eJCdta1ion in a narrow environment.
Hold time
Refers to the time period the lamp remains at 100% illumination after no
motion detected.
- Notice 1: The hold time can be ducted by the slide switch. The hold time counting shoo<Jld be started after the sensor is powered on and initialized.
Daylight sensor
The sensor can be set to only allow the lamp to illuminate below a defined
ambient brightness threes hold. When set to Disable mode, the daylight sensor
will switch on the lamp when motion is detected regardless of ambient light
level.
- Notice 1: The light threshold can be ,elected through the ~ide switch, it may cue a large deviation in different lamps.
Factory settings
Wiring Diagram
Induction Range
Safety Instructions
To ensure correct function and safety, please read and follow all instructions carefully before using the product:
- Turn off power before installation or before doing any maintenance work.
- Do not install any luminaire near the heat source.
- Do not exceed the nominal supply voltage or amperage ratings.
- All wiring and installation of the light fitting must adhere to local and national wiring rules.
- Take care not to pull any electrical wires during unpacking as this may damage the connection.
- Lay out all the components on a smooth surface and make sure there are no components missing before assembling.
- To avoid injury or damage to the fitting, please ensure that power leads and screws are secure before connecting the power.
- Please keep instructions for future reference.
Installation Procedure
WARNING
- Switch off before installation.
- Switch on only after complete installation and examination of the circuit.
- Turn Off power supply before starting any installation. Read instructions & check you have all the tools & accessories to complete the installation correctly.
- The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.
Surface mounted installation
Suspended installation 
Free Call: 1800 909 306
Website: nedlandsgroup.com.au
Email: sales@nedlandsgroup.com.au
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>