V I V O STAND-TV00Y Tabletop TV Stand Instruction Manual
- October 30, 2023
- V I V O
Table of Contents
V I V O STAND-TV00Y Tabletop TV Stand
INFORMATION
SKU: STAND-TV00
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product.
https://vivo-us.com products stand-tv00y
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
WARNING
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity.
We cannot be liable for damage or injury caused by improper mounting,
incorrect assembly or inappropriate use.
TIP OVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR TV STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
TOOLS NEEDED
DO NOT EXCEED WEIGHT CAPACITY.
- Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
Apply Soft Pads (C) to bottom of Base Plates (A1, B1). Connect Base Plate (A1)
to Junction Plate (A2) using M6x10mm Screws (S-A) as shown in diagram. Use 4mm
Allen Wrench (T-A) to tighten screws. Repeat this process with Base Plate (B1)
and Junction Plate (B2).
STEP 2
Assemble Upper TV Bracket (A4) to TV bracket (A3) using M6 Nut (S-C) and
tighten using Wrench (T-B). Repeat process with Upper TV Brackets (B4) and
Lower TV Bracket (B3).
STEP 3
Connect Lower TV bracket (A3) to Junction Plate (A2) using M6x10mm Screws
(S-A), M6 Cap Nut (S-B). Tighten using 4mm Allen Wrench (T-A) and Wrench
(T-B). Repeat process with Lower TV Bracket (B3) and Junction Plate (B2).
STEP 4
With TV facing down on a clean, flat surface, mount leg assemblies to the back
of the monitor using Screws (M-A through M-G) and washers (M-H through M-J)
depending on size of mounting holes in television. For curved monitors,
Spacers (M-K through M-M) may be required.
Love your new VIVO setup and want to share?
- Tag us in your photo! @vivo_us
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
309-278-5303: AVG. RESOLUTION TIME (within office hrs): 5M 4S
www.vivo-us.com Chat live with an agent! AVG.
RESOLUTION TIME (within office hrs): < 15 M
[email protected] AVG. RESPONSE TIME (within office
hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Tabletop Stand for 22" to 65" TVs – VIVO - desk solutions, screen mounting, and more