mo-vis P015-61 Scoot Control R-Net User Manual
- October 30, 2023
- mo-vis
Table of Contents
User manual
Edition 4, July 2021
Scoot Control
P015-61 Scoot Control R-net
Other languages
You can find this manual in English on our website.
Warning labels
Please read this manual, the safety instructions and warning texts carefully,
in order to reduce the risks associated to the device. Our products are safe
under normal and reasonably foreseeable operating conditions.
NOTE: This symbol indicates general notes and information.
CAUTION: This symbol indicates caution for a hazardous situation that, if
not avoided, could result in minor or moderate injury.
WARNING: This symbol indicates a warning for a hazardous situation that,
if not avoided, could result in death or serious injury.
Support, scrapping & recycling
Technical support
TROUBLE: In case of technical problems:
- Contact your dealer
- If your dealer is not available or unknown, please contact mo-vis: contact@mo-vis.com or +32 9 335 28 60.
Always state the product code and device serial number when contacting us.
This ensures you are provided with the correct information.
Spare parts and accessories
Contact mo-vis or your dealer for more information about spare parts and
accessories.
Scrapping & recycling
CAUTION: For scrapping, adhere to your local waste legislation.
Dispose of obsolete electronic parts responsibly in accordance with local
recycling regulations.
Limited liability
mo-vis accepts no liability for personal injury or damage to property that may
arise from the failure of the user or other persons to follow the
recommendation, warnings and instructions in this manual.
CAUTION: This product should only be installed by a qualified service
engineer.
NOTE: All mo-vis manuals can be found at http://www.mo-vis.com where
they can be consulted in PDF format.
NOTE: In case any serious incident occurs in relation to this device,
this should be reported immediately to mo-vis and the competent authority of
the Member State in which the user is established.
Intended use
The Scoot Control is a steering device which can be connected directly to the
wheelchair electronics (R-net), to control the power chair and its functions.
It is intended to support an attendant in controlling or maneuvering a power
chair, both inside and outside.
Safe driving
WARNING: The on/off switch must be available to the user at all times.
This allows to instantly stop the wheelchair in case of problems or an
emergency.
WARNING: In case the wheelchair responds in an unexpected way, the user
must immediately release the Scoot Control or use the power on/ off switch.
WARNING: Only adult attendant should operate the Scoot Control.
WARNING: When the wheelchair is in tilt/recline, please be aware that the
Scoot Control could collide with objects or people (especially if the Scoot
Control is not folded in).
Features
The Scoot Control is part of our range of input devices. It is to be mounted on the back of the power chair and is a steering device with 2 handles (similar to a compact bicycle steer). The Scoot Control R-net is only compatible with the R-net electronics of Curtiss-Wright.
- Fully proportional handlebar with 2 rubber handles and 2 configurable thumb throttles at either side
- Built in a compact housing, with a 3.5 mm stereo jack to connect an external actuator keypad (Curtiss-Wright CJSM2 compatible)
- Full access to wheelchair functions such as Lights, Horn and Speed settings
- Battery and speed display via LEDs
- On-board configuration possible
- Compatible with multiple types of power chairs equipped with R-net electronics
Operation
The Scoot Control consists of the following parts:
- Control panel: control the Scoot Control
- Handlebar: rubber handle at either side to steer the wheelchair
- Left and right throttle: to move the power chair forward and/or backward
- 3.5 mm jack to connect a Curtiss-Wright CJSM2 compatible Actuator Keypad
- Built-in sounder: to be used as horn
- R-net bus cable
Horizontal movements of the handle bar will result in a steering action of the
wheelchair (turning).
In combination with the thumb throttle it is possible to move the wheelchair
in any direction.
- Standard configuration: right throttle = forward, left throttle = backward
- If both throttles are operated simultaneously and that would result in conflicting direction, the chair will stop driving
WARNING: Do not hang things (e.g. backpacks) on the Scoot Control or the
throttle. This might damage the throttle and the device.
Furthermore, removing items suddenly from the throttle might lead to
unintended movement of the power chair if it is not in stand-by mode.
Control Panel
The buttons have the following functions:
BUTTON | FUNCTION | ACTION |
---|---|---|
S1 | On / Off | Switch the power chair on/off |
S2 | Left indicator | Switch the left indicator on/off |
S3 | Right indicator | Switch right indicator on/off |
Hold S2 for > 2 seconds | Hazard lights | Switch hazard lights on/off |
Hold S3 for > 2 seconds | Lights | Switch lights on/off |
S4 | Horn | Horn sounds as long as pressed |
S5 | Direction | Switch direction of the throttles |
S6 | Speed setting | Change the speed. The first click on S6 will show you the |
current speed setting. The next clicks will change the speed.
Hold S6 for > 2 seconds| Grab focus| Press long to grab control of the power
chair. See Scoot Control Installation Manual for more infor- mation.
LED indications on the control panel provide you with the following information:
LED | FUNCTION | INFORMATION |
---|---|---|
D11-D15 | Battery gauge | Battery indicator: is default on when Scoot Control is |
in focus
Speed setting| Speed indicator when setting the speed.
5 speeds = 5 green LED in a row (e.g. speed level 3 = 3 LEDs on)
Becomes active when pressing S6 and remains active for 5 seconds after last
speed change.
Error| D11 and D15 red, D13 flashes red, other LEDs are off: number of flashes
indicates the fault (see Scoot Control Installation manual)
Status| • In focus: battery indicator
• Not in focus: D13 green heartbeat flash
• Configuration: D13 green fast flash
D16| Left indicator| Green flash when left indicator is on
D17| Right indicator| Green flash when right indicator is on
LED| FUNCTION| INFORMATION
---|---|---
D16 + D17| Hazard lights / lights indicator| Both flash red when hazard lights
are on. Both are orange when the lights are on and the direction indicator is
off.
D18| Forward / reverse| In standard configuration: Forward = green Backward =
orange
No focus| Off
Stand-by| Flash green / orange (depending on direc- tion of throttle)
CAUTION: Pushing harder on the throttle will not increase the speed of
the power chair. To increase the speed, press S6 or change the settings of the
power chair.
Parts and accessories
The P015-61 Scoot Control R-net is always accompanied by the DP015-61-70-vv
Scoot Control User manual and the D-P015-61-71-vv Scoot Control Installation
manual.
The following parts and accessories are optionally available:
PART NUMBER | FUNCTION | INFORMATION |
---|---|---|
P016-98 Actuator Keypad Button R-net CJSM2 | You can connect an external |
Curtiss Wright CJSM2 compatible Actuator Keypad to the Scoot Control to
control the actuators of the power chair.| See Scoot Control Installation
Manual
P016-99 Actuator Keypad Paddle R-net CJSM2
P016-88 Actuator Keypad PRO Button R-net CJSM2
P016-89 Actuator Keypad PRO Paddle R-net CJSM2
M015-91 Scoot Control keypad bracket set| To mount an Actuator Keypad to the
Scoot Control| See Dimensions on page 24
M015-70 Scoot Control bracket set| Dedicated mounting part for the Scoot
Control| Available together with Scoot Control as P015-65 Scoot Control
bundle. See Dimensions on page 24
M015-71 Scoot Control bracket set short| Dedicated mounting part for the Scoot
Control| Available together with Scoot Control as P015-66 Scoot Control bundle
short. See Dimensions on page 24
Contact mo-vis or your dealer for more information about spare parts and accessories.
Qualifications
CAUTION: Only a qualified service engineer may install the device.
CAUTION: An incorrect programming of the wheelchair or device
electronics, may cause damage to the devices or injury to the user.
First time use
CAUTION: A qualified service engineer should assist during first time use of the device and make sure that all functions are clear to the user, including what to do in case of problems or doubt.
Cleaning
Clean all parts of the Scoot Control on a regular basis (monthly) or whenever needed.
- Gently remove dust and dirt with a damp cloth.
- Use only non-aggressive disinfectant cleaning agents.
CAUTION: Do not immerse in water or use excessive amounts of liquid.
CAUTION: Do not apply additional lubricants to the moving parts.
CAUTION: Pay special attention to the cleanliness of the throttles. Dirt
and liquids could lead to reduced functionality of the Scoot Control.
Warnings and limitations
NOTE: This product complies with the limit values for Electromagnetic
Compatibility (EMC) with respect to power wheelchairs, as set out in the
harmonized standards for the EU in the Medical Device Regulation, No.
2017/745.
WARNING: Do not cover or block the device to avoid uncontrolled behavior
of the device or the wheelchair.
Dimensions
Scoot Control
450 x 100 x 55 mm – 17.72 x 3.94 x 2.17 in (WxDxH)
Mounting Brackets
- M015-70 Scoot Control bracket set
- M015-71 Scoot Control bracket set short
|
---|---
mo-vis bv . Biebuyckstraat 15D .
9850 Deinze – Belgium
www.mo-vis.com
contact@mo-vis.com
. +32 9 335 28 60
Go to our website for more information on our products or share
your experience with us via email.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>