VAXCEL P0381 Monrovia Mini Pendant Light Instruction Manual
- October 30, 2023
- VAXCEL
Table of Contents
VAXCEL P0381 Monrovia Mini Pendant Light
Product Information
The product is a ceiling fixture that requires assembly and installation. It comes with a hardware package that includes an outlet box house ground wire, mounting strap unit (A), mounting screw (B), wire connector (C), bolt nut (D), and a canopy coupling kit. The fixture can be adjusted from 25-1/2 to 67-1/2 by using the three rods included in the package. It requires a maximum of 100W medium base bulb (not included) and is recommended for angled or vaulted ceilings.
Product Usage Instructions
-
Before starting the installation process, turn off the power at the fuse or circuit box.
-
Connect the fixture and socket by the threaded pipe.
-
Thread the fixture wire through the lower rod, then secure the lower rod onto the fixture using the threaded pipe. Repeat for middle and upper rods.
Note: use fewer rods if a shorter length is desired. -
Thread the fixture wire through the canopy kit, then secure the rod assembly to the set threaded pipe of the canopy kit.
-
Attach the mounting strap unit (A) to the outlet box by using two mounting screws (B).
-
Attach the canopy kit to the mounting strap unit (A) by inserting the fixture mounting screws, then secure it with two bolt nuts (D).
-
Attach the glass shade to fixture, then secure it with the socket ring.
-
Install a maximum of 100W medium base bulb (not included). See revamping label at socket area or packaging for maximum wattage allowed.
-
For angled or vaulted ceilings, angled mounting is recommended.
-
Once the installation is complete, turn on the power at the fuse or circuit box.
Note: Consult local electrical codes for wiring and grounding requirements before installing the fixture. Also, keep the instruction manual for future reference.
ASSEMBLY AND INSTALLATION INSTRUCTIONS
WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER WHILE INSTALLING OR SERVICING THIS FIXTURE.
NOTES
- Before installing, consult local electrical codes for wiring and grounding requirements.
- READ AND SAVE THIS INSTRUCTIONS.
Hardware Package (included)
Installation Steps
Turn off the power at fuse or circuit box.
-
Connect the fixture and socket by the threaded pipe.
-
Rod Connections:
-
Thread the fixture wire from the fixture through the lower rod, then secure the lower rod onto fixture using the threaded pipe.
-
Thread the fixture wire through the middle rod, and then secure the middle rod onto the lower rod using the threaded pipe.
-
Thread the fixture wire through the upper rod, and then secure the upper rod onto the middle rod using the threaded pipe.
Note: Length adjustable from 25-1/2″ to 67-1/2″. Use fewer rods if
shorter length is desired. -
Thread the fixture wire through the canopy kit, then secure the rod assembly to the set threaded pipe of the canopy kit.
-
Attach the mounting strap unit (A) to outlet box by using two mounting screws (B).
-
Pull out the source wires from the outlet box. Make wire connections using wire connectors (C) as follows:
- Connect the smooth-coated wire (marked) from the fixture to the black wire from the power source.
- Connect the ribbed-coated wire (unmarked) from the fixture to the white wire from the power source.
- Attach the fixture ground wire to the mounting strap unit (A) with the green ground screw, then connect it to the house ground wire with a wire connector (C). Carefully put the wires back into the outlet box.
-
Attach the canopy kit to the mounting strap unit (A) by inserting the fixture mounting screws, then secure it with two bolt nuts (D).
-
Attach the glass shade to fixture, then secure it with the socket ring.
-
Install 1 X 100W Max. medium base bulb (not included). See relamping label at socket area or packaging for maximum wattage allowed.
-
Angled mounting recommended for a vaulted or angled ceiling. (See Fig.1)
Turn on the power at fuse or circuit box.
The following parts are available for re-order if damaged or missing.
Spare Parts List
