Intel NUC Kit User Guide

Intel® NUC Kit NUC11PAKi7
Intel® NUC Kit NUC11PAKi5
Intel® NUC Kit NUC11PAKi3
User Guide

Introduction

This User Guide provides step-by-step installation instructions for these products:

• Intel® NUC Kit NUC11PAKi7
• Intel® NUC Kit NUC11PAKi5
• Intel® NUC Kit NUC11PAKi3

Before You Begin

CAUTIONS
The steps in this guide assume you’re familiar with computer terminology and with the safety practices and regulatory compliance required for using and modifying computer equipment.
Disconnect the computer from its power source and from any network before performing any of the steps described in this guide.
Failure to disconnect power, telecommunications links, or networks before you open the computer or perform any procedures can result in personal injury or equipment damage. Some circuitry on the board can continue to operate even though the front panel power button is off.
Follow these guidelines before you begin:

• Always follow the steps in each procedure in the correct order.
• Create a log to record information about your computers, such as model, serial numbers, installed options, and configuration information.
• Electrostatic discharge (ESD) can damage components. Perform the procedures described in this chapter only at an ESD workstation using an antistatic wrist strap and a conductive foam pad. If such a station isn’t available, you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the computer chassis.

Installation Precautions

When you install and test the Intel NUC, observe all warnings and cautions in the installation instructions.
To avoid injury, be careful of:

• Sharp pins on connectors
• Sharp pins on circuit boards
• Rough edges and sharp corners on the chassis
• Hot components (such as SSDs, processors, voltage regulators, and heat sinks)
• Damage to wires that could cause a short circuit

Observe all warnings and cautions that instruct you to refer computer servicing to qualified technical personnel.

Observe Safety and Regulatory Requirements

If you don’t follow these instructions, you increase your safety risk and the possibility of noncompliance with regional laws and regulations.

Open the Chassis

Unscrew the four corner screws on the bottom of the chassis and lift the cover.

Install and Remove System Memory

Intel NUC Kits NUC11PAKi7, NUC11PAKi5, and NUC11PAKi3 have two 260-pin DDR4 SO-DIMM memory slots
Memory requirements:

• 1.2V low voltage memory
• 3200 MHz SO-DIMMs
• Non-ECC

Find compatible system memory modules at the Intel® Product Compatibility Tool:

• NUC11PAKi7
• NUC11PAKi3
• NUC11PAKi3

Install SO-DIMMs

NOTE:  If you plan to install only one memory module, install it in the lower memory socket.
To install the SO-DIMMs, follow these steps:

1. Observe the precautions in “Before You Begin” in Section 1.1.

2. Turn off all peripheral devices connected to the computer. Turn off the computer and disconnect the AC power cord.
   

3. Align the small notch at the bottom edge of the SO-DIMM with the key in the socket.

4. Insert the bottom edge of the SO-DIMM into the socket.

5. When the SO-DIMM is inserted, push down on the outer edge of the SO-DIMM until the retaining clips snap into place. Make sure the clips are firmly in place.

Remove SO-DIMMs

To remove a SO-DIMM, follow these steps:

1. Observe the precautions in “Before You Begin” in Section 1.1.
2. Turn off all peripheral devices connected to the computer. Turn off the computer.
3. Remove the AC power cord from the computer.
4. Remove the computer’s cover.
5. Gently spread the retaining clips at each end of the SO-DIMM socket. The SO-DIMM pops out of the socket.
6. Hold the SO-DIMM by the edges, lift it away from the socket, and store it in an anti-static package.
7. Reinstall and reconnect any parts you removed or disconnected to reach the SO-DIMM sockets.
8. Replace the computer’s cover and reconnect the AC power cord.

Install an M.2 SSD or Intel® Optane™ Memory Module

Intel NUC Kits NUC11PAKi7, NUC11PAKi5, and NUC11PAKi3 support 80mm and 42mm SSDs.
Find compatible M.2 SSDs at the Intel® Product Compatibility Tool:

• NUC11PAKi7
• NUC11PAKi3
• NUC11PAKi3

If you’re installing an 80mm M.2 SSD:

1. Remove the small silver screw from the 80mm metal standoff on the motherboard (A).
2. Align the small notch at the bottom edge of the M.2 card with the key in the connector.
3. Insert the bottom edge of the M.2 card into the connector (B).
4. Secure the card to the standoff with the small silver screw (C).
   Intel® Optane™ Memory Module installation and integration instructions are available by this link

If you’re installing a 42mm M.2 SSD:

1. Remove the small silver screw from the metal standoff on the motherboard (A).
2. Move the standoff (B) from the 80mm position to the 42mm position (C).
3. Align the small notch at the bottom edge of the M.2 card with the key in the connector.
4. Insert the bottom edge of the M.2 card into the connector (D).
5. Secure the card to the standoff with the small silver screw (E).

Close the Chassis

After all components have been installed, close the Intel NUC chassis. Intel recommends this be done by hand with a  screwdriver to avoid over-tightening and possibly damaging the screws.

Use the VESA Bracket (Optional)

Follow these instructions to attach and use the VESA Mount bracket:

1. Using the four small black screws that were included in the box, attach the VESA bracket to the back of the monitor or TV.
   

2. Attach the two slightly larger black screws to the bottom chassis cover of the Intel NUC.

3. Slide the Intel NUC onto the VESA mount bracket.
   

Connect Power

Country-specific power plug attachments are included in the box.

1. Connect AC power.

Each Intel NUC model includes either a region-specific AC power cord or no AC power cord (only the power adapter).

RNUC11PAQi70QA0
RNUC11PAQi50WA0
RNUC11PAQi30WA0
RNUC11PAQi70000
RNUC11PAHi70000
RNUC11PAQi50000
RNUC11PAHi50000
RNUC11PAKi50000
RNUC11PAHi30000
RNUC11PAKi30000| No power cord included.
An AC power cord needs to be purchased separately. Power cords are available at many Internet sites for use in multiple countries.
The connector on the power adapter is a C5 type
connector.
RNUC11PAQi70QA1|
RNUC11PAQi50WA1
RNUC11PAQi30WA1
RNUC11PAQi70001
RNUC11PAHi70001
RNUC11PAKi70001
RNUC11PAQi50001
RNUC11PAHi50001
RNUC11PAKi50001
RNUC11PAHi30001
RNUC11PAKi30001| US power cord included.
---|---
RNUC11PAQi70QA2
RNUC11PAQi50WA2
RNUC11PAQi30WA2
RNUC11PAQi70002
RNUC11PAHi70002
RNUC11PAKi70002
RNUC11PAQi50002
RNUC11PAHi50002
RNUC11PAKi50002
RNUC11PAHi30002
RNUC11PAKi30002| EU power cord included.
RNUC11PAQi70QA3
RNUC11PAQi50WA3
RNUC11PAQi30WA3
RNUC11PAHi70003
RNUC11PAHi50003
RNUC11PAKi50003
RNUC11PAHi30003
RNUC11PAKi30006| UK power cord included.
RNUC11PAQi70QA4
RNUC11PAQi50WA4
RNUC11PAQi30WA4
RNUC11PAHi70004
RNUC11PAHi50004
RNUC11PAKi50004
RNUC11PAHi30004
RNUC11PAKi30004| Australia/New Zealand power cord included.
RNUC11PAHi70005
RNUC11PAHi50005| India power cord included.
RNUC11PAHi30005|
RNUC11PAQi70QA6
RNUC11PAQi50WA6
RNUC11PAQi30WA6
RNUC11PAHi70006
RNUC11PAHi50006
RNUC11PAKi50006
RNUC11PAHi30006
RNUC11PAKi30006| China power cord included.

Install an Operating System

See Supported Operating Systems for a list of Intel-validated Windows operating systems.
The Intel Product Compatibility Tool lists versions of Linux that have been reported as compatible by Intel NUC owners. If you need assistance with Linux on your Intel NUC, check the distribution’s website and forums for peer assistance.
Refer to Operating System Installation for system requirements and installation steps.

Install the Latest Device Drivers and Software

Here are the options for keeping device drivers current:

• Allow the Intel® Driver & Support Assistant (Intel® DSA) to detect out-of-date drivers
• Manually download drivers, BIOS, and software from Download Center:
  • NUC11PAKi7
  • NUC11PAKi5
  • NUC11PAKi3

The following device drivers and software are available.

• Intel® Chipset Device Software
• Intel® HD Graphics
• Intel® Management Engine
• Intel® Gigabit Ethernet
• Intel® Wireless
• Intel® Bluetooth
• Intel® USB 3.0 (needed for Windows 7* only)
• Intel® Serial IO
• Realtek* High Definition Audio
• ITE Tech* Consumer Infrared
• Intel® Rapid Storage Technology
• Intel® Software Guard Extensions

You may not use or facilitate the use of this document in connection with any infringement or other legal analysis concerning Intel products described herein. You agree to grant Intel a non-exclusive, royalty-free license to any patent claim thereafter drafted which includes subject matter disclosed herein.
No license (express or implied, by estoppel or otherwise) to any intellectual property rights is granted by this document.
All information provided here is subject to change without notice. Contact your Intel representative to obtain the latest Intel product specifications and roadmaps.
The products described may contain design defects or errors known as errata which may cause the product to deviate from published specifications. Currently characterized errata are available on request.
Copies of documents that have an order number and are referenced in this document may be obtained by calling 1-800-548-4725 or by visiting: http://www.intel.com/design/literature.htm.
Intel technologies features and benefits depend on system configuration and may require enabled hardware, software or service activation.
Performance varies depending on system configuration. No computer system can be absolutely secure.
Intel and the Intel logo are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries.
*Other names and brands may be claimed as the property of others.
Copyright © 2021, Intel Corporation. All rights reserved.

Revision History

NUC11PAKi7, NUC11PAKi5, NUC11PAKi3
User Guide – January 2021

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>