XTOOL TPMS2 Tire Pressure Sensor User Manual

: June 15, 2024
: XTOOL

Table of Contents

XTOOL TPMS2 Tire Pressure Sensor
Product Information
Product Usage Instructions
Warranty
Exploded View
Specifications
Installation Guide
Install TS101 Sensor
FCC Statement
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

XTOOL TPMS2 Tire Pressure Sensor

Product Information

Specifications

Sensor Weight (valve not included): approx. 13 g
Dimensions (valve not included): 46.1 x 25 x 16.2mm (1.81 x 0.98 x 0.64)
Max. Pressure: 900 kPa (9.0 bar or 130.5 psi)
Max. Speed: 240 km/h (150mph)

Product Usage Instructions

Installation Guide

Deflate & Uninstall Tire: Take off the valve cap and the valve core to deflate the tire. Then, use tools (or machines) to uninstall the tire from the rim.
In case of replacing the sensor only, deflate the tires, pry up the tire near valve stem until the sensor is exposed. Do not break the tire bead near the valve stem, or the original sensor may get damaged.
Uninstall Sensor: Take off the valve nut, washer, and screw from the valve stem. Then, take the sensor assembly out from the rim.
Here shows the process of uninstalling TS101 sensor. If you have problems when uninstalling other sensors, please check therepair manual or installation guide for uninstalling steps.
Install TS101 Sensor: Insert the TS101 sensor
assembly into the rim where the previous sensor was removed. Secure it with the screw, valve nut, and washer onto the valve stem.

FAQ

Frequently Asked Questions

What is the weight of the sensor?
The sensor weighs approximately 13 g (valve not included).
What are the dimensions of the sensor?
The sensor dimensions are 46.1 x 25 x 16.2mm (1.81 x 0.98 x 0.64) without the valve.
What is the maximum pressure supported by the sensor?
The sensor can handle a maximum pressure of 900 kPa (9.0 bar or 130.5 psi).
What is the maximum speed supported by the sensor?
The sensor can withstand a maximum speed of 240 km/h (150mph).

TS101 Universal Tire-Pressure Sensor User Manual (Metal Valve / Clamp-in Style)

Disclaimer

Please read this manual carefully before installing TS101 universal tire sensor (hereinafter referred to as TS101). For safety reasons, all the installation and maintenance operations should be carried out by trained professionals, with the guidance of vehicle manufacturer. Tire valves are vehicle-safety-related component and incorrect installations may cause malfunctions for tire valves or TPMS sensors. Shenzhen Xtooltech Intelligent Co., Ltd. (hereinafter referred to as “Xtooltech”) does not assume any liability in case of incorrect installation of the product. Pictures illustrated here are for reference only and this user manual is subject to change without prior notice.

Warranty

TS101 sensor is guaranteed to be free from material or manufacturing defects for 24 months or 40,000km (25,000 miles), whichever comes first. In case of defections caused by material or workmanship, Xtooltech will repair or replace (according to the situations) the product or parts for free by inspecting the proof of purchase. Xtooltech are not responsible for defects caused in the following circumstances:

Incorrect installation;
Irregular usage;
Damage caused by collision or tire damage;
Exceeding specific using limits of the product

Exploded View

Screw
Sensor
Valve stem, Rubber Washer & Valve Core Assembly
Valve Nut & Washer
Valve Cap

Warning

Make sure the sensor has already been programmed before use. We strongly recommend to program the sensor before installing tires.
Do not install a programmed TS101 sensor inside a broken wheel.
To ensure the best performance, do not install valve stems from other manufacturers, or install other parts which is not included inside TS101 sensor.
After finished installation, please test the TPMS system according to the guidance inside user manual from the original vehicle manufacturer, in order to confirm that the sensor is installed correctly.
When the tire is removed, it is highly recommended to replace or service the sensor. If the tire is using rubber valve, the valve stem must be replaced.
When driving vehicles with TS101 installed, the speed should be under 240km/h (150mph) and the tire pressure should be no higher than 900 kPa (9.0 bar or 130.5 psi).

Specifications

Sensor Weight (valve not included)	approx. 13 g
Dimensions (valve not included)	46.1 x 25 x 16.2mm (1.81″ x 0.98″ x 0.64″)
Max. Pressure	900 kPa (9.0 bar or 130.5 psi)
Max. Speed	240 km/h (150mph)

Installation Guide

Every time the tire been repaired, dismantled, or uninstalling & replacing TS101 sensors, make sure that the original rubber washer, screws, nuts and valve stems from TS101 are used in order to keep good air tightness. If the tire or wheel is damaged externally, the TS101 sensor must be replaced.
The torque of the valve tighening screw should be 4Nm (2.95 lb·ft).

Deflate & Uninstall Tire

Take off the valve cap and the valve core to deflate the tire.
Then, use tools (or machines) to uninstall the tire from the rim.
In case of replacing the sensor only, deflate the tires, pry up the tire near valve stem until the sensor is exposed. Do not break the tire bead near the valve stem, or the original sensor may get damaged

Uninstall Sensor

Take off the valve nut, washer and screw from the valve stem.
Then, take the sensor assembly out from the rim.
Here shows the process of uninstalling TS101 sensor. If you have problems when uninstalling other sensors, please check the repair manual or installation guide for uninstalling steps.

Install TS101 Sensor

Use the screw to assembly the valve core and the TS101 sensor tightly.
Uninstall the valve nut, washer and valve cap.
Adjust the angle of the sensor, then insert the valve core inside the valve hole, and make sure that the TS101 sensor is inside the rim.
Install the valve nut and washer back to the valve core.
Lock the nut with 4Nm (2.95 lb·ft) of torque.
Install the tire back, inflate the tire to standard tire pressure (see vehicle nameplate), and install the valve cap.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Caution : Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information

The device has been evaluated to meet general RF exposure requirements.
The device can be used in 0mm exposure conditions, and compliance with exposure requirements.

Shenzhen Xtooltech Intelligent Co., Ltd.
Address: 17&18/F, A2 Building, Creative City, Liuxian Avenue, Nanshan District, Shenzhen, China
For cooperation or business inquiries, please contact: marketing@xtooltech.com

Contact Us