V I V O STAND-TV86B Black Steel Easel Studio TV Stand Instruction Manual
- October 30, 2023
- V I V O
Table of Contents
STAND-TV86B Black Steel Easel Studio TV Stand
Instruction Manual
STAND-TV86B Black Steel Easel Studio TV Stand
SKU: STAND-TV86B
Scan the QR code with your mobile device or follow the link for helpful videos
and specifications related to this product.
https://vivo-us.com/products/stand-tv86b
GET IN TOUCH
Monday-Friday from 7:00am-7:00pm CST
help@vivo-us.com
www.vivo-us.com
Chat live with an agent!
309-278-5303
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT
TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR TV STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD
STUDS TO MOUNT. We include mounting hardware for brick and concrete walls. If
unsure, please contact us at vivo-us.com, email at help@vivo-
us.com, or call us at 309-278-5303.
PACKAGE CONTENTS
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
TOOLS NEEDED
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
Remove the cable management covers from Legs (B).
STEP 2
Assemble Legs (B) to Base (A) using M6x30mm Screws (S-A) and M5mm Allen Wrench
(T-B).
STEP 3
Thread Poles (C) onto Base (A).
STEP 4
Loosen the collars on Poles (C) using 4mm Allen Wrench (T-A). Adjust collars
to hold TV at desired height, using a tape measure to ensure the rings are
adjusted evenly, and tighten with 4mm Allen Wrench (T-A).
NOTE: Rings should be 2”-6” below the tops of the poles.
STEP 5
Remove the screws from Lower VESA Bracket (E) and open the clamps.
OPTION A: Flat Back Monitor
Secure Upper VESA Bracket (D) and Lower VESA Bracket (E) to the back of the TV
using Screws (M-A or M-B) with Square Washers (M-F) and M5 Washers (M-I), with
Security Clips (G) installed in the top holes.| OPTION B: Curved Back
Monitor
Secure Upper VESA Bracket (D) and Lower VESA Bracket (E) to the back of the TV
using Screws (M-C, M-D or M-E) with Square Washers (M-F) and Spacers (M-G,
M-H) with Security Clips (G) installed to top holes.
---|---
|
STEP 6
Slide the TV with Upper VESA Brackets (D) and Lower VESA Bracket (E) onto
Poles (C). Close the clamps on Lower VESA Bracket (E) around Poles (C) and
secure with previously removed screws.
NOTE: Make sure the TV does not touch Base (A).
STEP 7
Route cables through Legs (B) and secure using the previously removed cable
management covers.
STEP 8 (Option A)
Wood Stud Wall:
Using Security Cable Clamps (H) as guides, mark drilling locations on wall at
the same height as Upper VESA Bracket (D). Use of a stud finder is
recommended. Drill holes at least 1.6” (40mm) deep using a 1/8” (3.5mm) drill
bit. Mount clamps to wall using ST4.8×38 Screws (W-A). Thread Security Cable
(F) through Security Clips (G) on TV and center holes in Security Cable Clamps
(H) as shown, then tighten clamps using the 2mm Allen wrench (T-C).| STEP 8
(Option B)
Concrete/Brick Wall:
Using Security Cable Clamps (H) as guides, mark drilling locations on wall at
the same height as Upper VESA Bracket (D), spaced 16” – 26” (400mm – 650mm)
apart. Drill holes at least 1.6” (40mm) deep using a 9/32” (7mm) drill bit.
Insert Concrete Anchors (W-B) into holes and mount Security Cable Clamps (H)
to wall using ST4.8×38 Screws (W-A). Thread Security Cable (F) through
Security Clips (G) on TV and center holes in Security Cable Clamps (H) as
shown, then tighten clamps using the 2mm Allen Wrench (T-C).
---|---
|
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
| 309-278-5303| AVG. RESOLUTION TIME (within office hrs): 5M 4S
---|---|---
| www.vivo-us.com
Chat live with an agent!| AVG. RESOLUTION TIME (within office hrs): < 15 M
| help@vivo-us.com| AVG. RESPONSE TIME (within
office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-
us.com
LAST UPDATED: 08/29/2022
REV1
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Black Steel Easel Studio TV Stand – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>