V I V O STAND-TV65C Solid Wood TV Floor Stand Instruction Manual
- October 30, 2023
- V I V O
Table of Contents
V I V O STAND-TV65C Solid Wood TV Floor Stand Instruction Manual
WARNING
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury
TOOLS NEEDED
ASSEMBLY STEPS’
STEP 1
Assemble Side Legs (B) to Center Brace (D) using M6x70mm Screws (S-A) and 4mm
Allen Wrench (T-A).
STEP 2
Loosen the screw on the back of Pole (C) using 4mm Allen Wrench (T-A) and
connect Pole (C) to Center Leg (A). Assemble Center Leg (A) to Center Brace
(D) using M6x70mm Screw (S-A) and 4mm Allen Wrench (T-A). Attach Cover (G) to
the assembly.
NOTE: To remove Cover (G), press on the right sid
STEP 3
Ensure that the flathead screw in the back of Pole (C) is positioned
vertically as shown below. Thread M6x90mm Screw (S-B) into the bottom of
Center Leg (A) using4mm Allen Wrench (T-A). Retighten the screw in the back of
Pole (C) using 4mm Allen Wrench (T-A).
STEP 4
Slide Collar (H) and M45.5 Spacer (S-C) over Pole (C) and secure it in the
desired location using M6x30mm Screw (S-D) and 4mm Allen Wrench (T-A).
STEP 5
Remove the Security Screw (F1) from Lower VESA Bracket (F) and open the clamp
STEP 6
OPTION A: Flat Back Monitor
Position VESA brackets horizontally on the back of the TV, making sure Upper
VESA Bracket (E) is on top and Lower VESA Bracket (F) is below. Secure using
screws (M-A or M-B) with Square Washers (M-F), M5 Washers (P-G), and Security
Clips (P-B) installed to top holes.
OPTION B: Curved Back Monitor
Position VESA brackets horizontally on the back of the TV, making sure Upper
VESA Bracket (E) is on top and Lower VESA Bracket (F) is below. Secure using
screws (M-C, M-D or M-E) with Square Washers (M-F) and Spacers (M-G, M-H) with
Security Clips (P-B) installed to top holes.
STEP 7
Slide the TV with VESA Brackets (E, F) onto Pole (C), letting Upper VESA
Bracket (E) rest on Collar (H). Close the clamp on Lower VESA Bracket over
Pole (C) and secure with previously removed Security Screw (F1). Remove the
magnetic cable channel cover on the back of Center Leg (A) and route cables.
STEP 8 (Option A)
Wood Stud Wall
Using Security Bracket (P-C) as a guide, mark the drilling location on wall at
the same height as the upper VESA bracket. Use of a stud finder is
recommended. Drill the hole at least 1.6” (40mm) deep using a 1/8” (3.5mm)
drill bit. Mount clamp to wall using ST4.8x38mm Screws (P-E). Thread Security
Cable (P-A) through Security Clips (P-B) on TV and center holes in Security
Brackets (P-C) as shown, then tighten Security Cable Clamps (P-D) with a
Phillips screwdriver.
STEP 8 (Option B)
Concrete/Brick Wall
Using Security Bracket (P-C) as a guide, mark the drilling location on wall at
the same height as Upper VESA Bracket (E). Drill the hole at least 40mm (1.6”)
deep using a 7mm (9/32”) drill bit. Mount Security Bracket (P-C) to wall using
Anchor (P-F) and ST4.8x38mm Screw (P-E). Thread Security Cable (P-A) through
Security Clips (P-B) on TV and center holes in Security Brackets (P-C) as
shown, then tighten Security Cable Clamps (P-D) using a Phillips screwdriver.
Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
309-278-5303 AVG. RESOLUTION TIME (within office hrs): 5M 4S
www.vivo-us.com AVG. Chat live with an agent! RESOLUTION TIME (within office hrs): < 15 M
help@vivo-us.com AVG. RESPONSE TIME (within office hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
SKU: STAND-TV65C
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. Instruction Manual
https://vivo-us.com/products/stand-tv65c
help@vivo-us.com
Chat live with an agent!
309-278-5303
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Solid Wood TV Floor Stand for 45" to 65" TVs – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>