FLEX Trinity AG FT700 and FT750 User Guide

: June 4, 2024
: FLEX

FLEX Trinity AG FT700 and FT750

FLEX-Trinity-AG-FT700-and-FT750-PRODUCT

Key Value Proposition

Advanced Capabilities
Internal and External Antennas

Applications

Heavy Truck
School Buses

Capabilities

Motion Detection
High-Frequency Tracking
Vehicle Diagnostics (ISO-15765, J1939)
Ignition Detection
Ignition On Tamper Detection
Starter Disable (via relay)
Operator ID (1-wire)
Digital inputs / outputs

Future Capabilities

Driver Behavior
ELD tablet communication
Camera video upload

Dimensions

7.3” x 3.23” x 1.22” (184mm x 82mm x 31mm)

Location

GPS (multi-constellation)
Assisted acquisition: 2s (via cloud)
Acquisition Sensitivity: -160dBm (1)
Tracking Sensitivity: -167dBm (2)

Internal Sensors

9-axis IMU
System temperature
Battery level

Internal Antennas

Cellular primary and secondary
GPS, Bluetooth, WiFi

External Connectors

Cellular primary
GPS
USB
Power in (6-48VDC)
Power out (2.5W)
1-Wire
ADC (48V) x 2
Digital Input x4
Digital Output x 3
Ignition Detection
CAN 2.0B x1 (ISO-15765 or J1939) CAN 2.0B or FD x1 (ISO-15765 or J1939) RS-232 x2
ISO-9141 (K line for Tachometer) J1708 (Firmware support TBC)
Battery 1.3Ah

Global Cellular Connectivity

FT-700 Standard SKU:

4G (Cat M/NB-IoT) Global Bands
2G: 850,900,1800,1900

Local Area Connectivity

WiFi: 802.11 b/g/n (2.4GHz) station & softAP (6) BLE: 5.0 (master, slave, LE data packet length)
USB: mass storage (host), ACCM (client)

Operating Temperature

Powered: -40˚C – 70˚C
Battery: -20˚C – 60˚C
Charging: 0˚C – 45˚C

Housing

Industrial grade Polycarbonate (PC)
Ingress Protection (IP): 4X

Security

Secure boot
TLS/SSL
FIPS 140-2 (Optional)

Certifications

FCC, IC, CE, PTCRB, RCM

Environmental

RoHS, Reach, SAEJ1455 [Thermal Shock (4), Humidity (5), Mechanical Vibration, Mechanical Shock, Electrostatic Discharge

User Interface

Power button, 5 LEDs Buzzer

FCC Regulations

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.

RF Exposure Information

This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm
during normal operation.

ISED Notice
This device complies with Innovation, Science and Economic Development
Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

this device may not cause interference, and
this device must accept any interference, including interference that may cause undesired operation of the device.

ISED RF Exposure Statement

This device complies with ISED RSS-102 RF exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the IC RSS-102 RF exposure limits, human proximity to the antenna shall not be less than 20cm (7.87 inches) during normal operation.