3M 3443-82-20 Locator Plate Installation Guide
- October 30, 2023
- 3M
Table of Contents
3M 3443-82-20 Locator Plate
Product Information
The 3MTM Locator Plate 3443-82-XX is a durable metal plate used for the assembly of 3MTM Ribbon Cable Sockets, Series 451 with a size of .05 x .05 and 3MTM Flat Ribbon Cable .025. It is designed to be used with the 3MTM Assembly Press, Models 3640 and 3335. The product also comes with a customer 3D printed option for lower volume applications. The product can be used with connector part numbers 45104, 45106, 45108, 45110, 45112, 45114, 45116, 45120, 45126, 45130, 45134, 45140, and 45150.
Usage Instructions
- Adjust the press shut height by rotating the shut height to lower or raise adjustment feature until the bottom of the shaft tightly contacts the desired position on the shut height gauge.
- Install the 3MTM Locator Plate and the appropriate platen on the press. The platen should be positioned parallel with the connector body and cover.
- Cut the cable end cleanly with a sharp blade. The end must be at a 90 degree angle to the length of the cable.
- Place the cover into the locator plate.
- Slide the properly sized ribbon cable onto the cover in the locator plate. Use 0.0625 diameter dowel pins in the cable-stop location holes if desired. Cable-stop location holes are not available on sizes 4, 6, 8 and 10.
- Place the socket connector onto the cover over the cable, verifying the pin 1 indicator is in the correct position.
- Bring the handle of the press down until the IDCs press into cable and the connector fully seats into the cover.
- Visually inspect termination to ensure that the cover is fully seated and parallel to the body, cover latches are fully engaged, cable is properly aligned with the cover, and cover retaining devices on the body are flush with the cover ends.
General
The assembly of 3M™ Ribbon Cable Sockets, Series 451 .05” x .05” and 3M™ Flat Ribbon Cable .025” can be accomplished when using the durable metal 3M™ Locator Plates, Series 3443-82-XX and the 3M™ Assembly Press, Models 3640 and 3335. A customer 3D printed 3M™Locator Plate 3443-81-XX option is available for lower volume applications. See drawing 78-5100-2644-2 and Instructions Guide 78-9102-1086-9.
Connector Part Number| Locator Plate Number| Platen Part
Number| 3436-1K Shut Height Setting
---|---|---|---
Press 3640/3316| Press 3335
45104| 3443-82-04| 3442-9| 7| 7.5
45106| 3443-82-06| 3442-9| 7| 7.5
45108| 3443-82-08| 3442-9| 7| 7.5
45110| 3443-82-10| 3442-9| 7| 7.5
45112| 3443-82-12| 3442-9| 7| 7.5
45114| 3443-82-14| 3442-9| 7| 7.5
45116| 3443-82-16| 3442-9| 7| 7.5
45120| 3443-82-20| 3442-9| 7| 7.5
45126| 3443-82-26| 3442-9| 7| 7.5
45130| 3443-82-30| 3442-9| 7| 7.5
45134| 3443-82-34| 3442-9| 7| 7.5
45140| 3443-82-40| 3442-9| 7| 7.5
45150| 3443-82-50| 3442-9| 7| 7.5
Locator Plate Features
Procedures for Adjusting the Press Shut Height
The shut height should be adjusted from the base before the locator plate is put into place. The 3M™ Assembly Presses 3316 and 3640 are adjusted with a knob at the top of the press. The 3M™ Assembly Press 3335 is adjusted with the collar on the press shaft and 3M™ Assembly Press 3830 is self-adjusting. The shut height adjustment is made from the base of the assembly press without the locator plate or platen in pace. Lower the handle of the press until the handle casting makes contact with the press casting (See Figure 2)
- Place the shut height gauge across the press base.
- Rotate the shut heigh to lower or raise adjustment feature until the bottom of the shaft tightly contacts the desired position on the shut height gauge. (See Figures 3 and 4).
- Install the 3M™ Locator Plate and the appropriate platen on the press. The platen should be positioned parallel with the connector body and cover. (See Figure 5)
Procedures for Cable Termination
Before assembly of the connector can take place, the cable end must be cleanly cut with a sharp blade. The end must be at a 90 degree angle to the length of the cable.
- Place the cover into the locator plate. (See Figure 6)
- Slide the properly sized ribbon cable onto the cover in the locator plate (See Figure 7). 0.0625” diameter dowel pins can be used in the cable-stop location holes if so desired. Cable-stop location holes are not available on sizes 4, 6, 8 and 10.
- Place the socket connector onto the cover over the cable, verifying the pin 1 indicator is in the correct position. (See Figure 8)
- Bring the handle of the press down until the IDCs press into cable and the connector fully seats into the cover. (See Figure 9)
Visually inspect termination to ensure that:
- Cover is fully seated and parallel to the body. Cover latches are fully engaged.
- Cable is properly aligned with the cover
- Cover retaining devices on the body are flush with the cover ends (See Figure 10)
Strain Relief Attachment
- Fold the cable back over the cover. (See Figure 11)
- Place the strain relief in the connector over the cable, sliding the strain relief into the slots of the connector. (See Figure 12)
- Press the strain relief down until the strain relief snaps into the correct position on the connector. (See Figure 13)
Regulatory: For regulatory information about this product, contact your
3M representative.
Technical Information: The technical information, guidance, and other
statements contained in this document or otherwise provided by 3M are based
upon records, tests, or experience that 3M believes to be reliable, but the
accuracy, completeness, and representative nature of such information is not
guaranteed. Such information is intended for people with knowledge and
technical skills sufficient to assess and apply their own informed judgment to
the information. No license under any 3M or third party intellectual property
rights is granted or implied with this information.
Product Use: Many factors beyond 3M’s control and uniquely within user’s knowledge and control can affect the use and performance of a 3M product in a particular application. As a result, customer is solely responsible for evaluating the product and determining whether it is appropriate and suitable for the customer’s application, including conducting a workplace hazard assessment and reviewing all applicable regulations and standards (e.g., OSHA, ANSI, etc.). Failure to properly evaluate, select, and use a 3M product in accordance with all applicable instructions and with appropriate safety equipment, or to meet all applicable safety regulations, may result in injury, sickness, death, and/or harm to property.
Warranty
Warranty, Limited Remedy, and Disclaimer: Unless a different warranty is
specifically stated on the applicable 3M product packaging or product
literature (in which case such warranty governs), 3M warrants that each 3M
product meets the applicable 3M product specification at the time 3M ships the
product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR ANY IMPLIED WARRANTY OR
CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOM, OR USAGE OF TRADE. If a
3M product does not conform to this warranty, then the sole and exclusive
remedy is, at 3M’s option, replacement or repair of the 3M product or refund
of the purchase price.
Limitation of Liability: Except for the limited remedy stated above, and
except to the extent prohibited by applicable law, 3M will not be liable for
any loss or damage arising from or related to the 3M product, whether direct,
indirect, special, incidental, or consequential (including, but not limited
to, lost profits or business opportunity), regardless of the legal or
equitable theory asserted, including, but not limited to, warranty, contract,
negligence, or strict liability.
Disclaimer: For industrial use only. Not intended, labeled or packaged
for consumer sale or use.
Electronics Materials Solutions Division
3M Center, Building 224-3N-11 St. Paul, MN 55144-1000
1-800-251-8634 phone
651-778-4244 fax
www.3M.com/electronics
3M is a trademark of 3M Company.
Please recycle.
©3M 2022. All rights reserved.
78-9101-8937-8
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>