V I V O STAND-TS38B-BW Dual Monitor Desk Stand Instruction Manual
- October 30, 2023
- V I V O
Table of Contents
Dual Monitor Desk Stand
Instruction Manual
STAND-TS38B-BW Dual Monitor Desk Stand
SKU: STAND-TS38B/BW
Scan the QR code with your mobile device or follow the link for helpful videos
and specifications related to this product. https://vivo-us.com/products
/stand-ts38b
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
| help@vivo-us.com
---|---
| www.vivo-us.com
Chat live with an agent!
| 309-278-5303
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT
TIPOVER:
- TO PREVENT TIPPING, PLEASE BE CAREFUL NOT TO EXTEND THE ARMS TOO FAR FORWARD OR BACKWARD.
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
TOOLS NEEDED
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
Install Pole (A) to Base (B) using M5x16mm Flathead Screw (S-A) and 3mm Allen
Wrench (T-A). STEP 2
Slide Pole Cable Clip (F) and Swivel Arm (C) onto Pole (A) and tighten with
6mm Allen Wrench (T-C). Assemble Arm Cable Clips (E) to Swivel Arm (C).STEP 3 (Option A)
Flat Back Monitor
Attach VESA Plates (D) to the monitors using M4x12mm Thumbscrews (M-A).
NOTE: Hand tighten screws to avoid stripping the plastic screw heads.STEP 3 (Option B)
Curved Back Monitor
Attach VESA Plates (D) to the monitors using M4 Spacers (M-C) and M4x30mm
Screws (M-B). Tighten with a Phillips screwdriver. STEP 4
Slide the monitors with VESA Plates (D) onto the heads of Swivel Arm (C) and
install Security Nuts (S-B). Make sure Security Nuts (S-B) are installed
before you rotate the monitors. STEP 5
Tighten the bolt on the side of the tilt joint using 5mm Allen Wrench (T-B) to
fix the tilt angle.To level the monitors, remove the security
nut and turn the bolt with 3mm Allen Wrench (T-A) to raise or lower the
monitor. Replace nut after the adjustment.STEP 6
Use 3mm Allen Wrench (T-A) to adjust joints if needed. Manage cables and store Allen Wrenches in Pole Cable Clip (G) for
future use. Love your new VIVO setup and want to
share?
Tag us in your photo! @vivo_us
Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer
immediate assistance with rapid response times. If any parts are received
damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
| 309-278-5303| AVG. RESOLUTION TIME (within office hrs): 5M 45
---|---|---
| www.vivo-us.com
Chat live with an agent!| AVG. RESOLUTION TIME (within office hrs): < 15 M
| help@vivo-us.com| AVG. RESPONSE TIME (within
office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < lhr
– 83% within < 2hr
– 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
LAST UPDATED: 11/07/2022
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Telescoping Dual Monitor Desk Stand – VIVO - desk solutions, screen mounting, and more