VAXCEL P0375 Ellis 12 Light Pendant Instruction Manual

VAXCEL P0375 Ellis 12 Light Pendant

Product Information

The product is a light fixture that can accommodate a maximum of 60W type B bulb (not included). It comes with a mounting plate unit, hardware package, and canopy kit for installation. The fixture is adjustable in length from 23-3/4 to 68-3/4 inches by using the threaded rods provided. It is designed for use in accordance with local electrical codes for wiring and grounding requirements. The fixture should be installed by a qualified electrician to avoid the risk of electrical shock.

Product Usage Instructions

1. Turn off the power at the fuse or circuit box.
2. Attach the mounting plate unit (A) to the outlet box using two mounting screws (B).
3. Adjust the arms of the fixture according to the picture on the package.
4. Thread the fixture wire through the lower rod, middle rod, and upper rod respectively, securing each rod onto the fixture using the threaded pipe provided. Note: Use fewer rods if a shorter length is desired.
5. Thread the fixture wire through the canopy kit, then secure the rod assembly to the set threaded pipe of the canopy kit.
6. Pull out the source wires from the outlet box and make wire connections using wire connectors (C) as follows:
   • Connect the smooth-coated wire (marked) from the fixture to the black wire from the power source.
   • Connect the ribbed-coated wire (unmarked) from the fixture to the white wire from the power source.
   • Attach the fixture ground wire to the mounting strap unit (A) with the green ground screw, then connect it to the house ground wire with a wire connector (C).
7. Carefully put the wires back into the outlet box.
8. Attach the canopy kit to the mounting plate unit (A), and the secure it with two bolt nuts (D).
9. Install 12 x 60W Max. candelabra base bulbs (not included). See relamping label at socket area or packaging for maximum wattage allowed.
10. Angled mounting is recommended for a vaulted or angled ceiling.
11. Turn on the power at the fuse or circuit box.

WARNING

• TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
• POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE

NOTES:

1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.

Hardware Package included

OVERVIEW

Installation Steps

1. Attach the mounting plate unit (A) to the outlet box by using two mounting screws (B).

2. Adjust the arms of the fixture according to picture on the package.

3. Rod Connections:

4. a. Thread the fixture wire from the fixture through the lower rod, then secure the lower rod onto fixture using the threaded pipe.

5. b. Thread the fixture wire through the middle rod and then secure the middle rod onto the lower rod using the threaded pipe.

6. c. Thread the fixture wire through the upper rod, then secure the upper rod onto the middle rod using the threaded pipe.
   Note : Length adjustable from 23-3/4″ to 68-3/4″. Use fewer rods if shorter length is desired.

7. Thread the fixture wire through the canopy kit, then secure the rod assembly to the set threaded pipe of the canopy kit.

8. Pull out the source wires from the outlet box. Make wire connections using wire connectors (C) as follows:

9. Connect the smooth-coated wire (marked) from the fixture to the black wire from the power source.

10. Connect the ribbed-coated wire (unmarked) from the fixture to the white wire from the power source.

11. Attach the fixture ground wire to the mounting strap unit (A) with the green ground screw, then connect it to the house ground wire with a wire connector (C). Carefully put the wires back into the outlet box.

12. Attach the canopy kit to the mounting plate unit (A), and then secure it with two bolt nuts (D)

13. Install 12 x 60W Max. candelabra base bulbs (not included). See relamping label at socket area or packaging for maximum wattage allowed.

14. Angled mounting recommended for a vaulted or angled ceiling

Turn on the power at fuse or circuit box
The following parts are available for re-order if damaged or missing

Spare Parts List

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>