cureUV 201075 Wall Mountable UVC Air Purifier and HEPA Filter Instruction Manual
- June 12, 2024
- cureuv
Table of Contents
Wall Mountable UVC Air Purifier and HEPA Filter
SKU: 201075
INSTRUCTION MANUAL Clean air has never been so easy
DEVICE SPECIFICATIONS
SIZE | 13.1″ x 5.1″ x 11.7″ |
---|---|
WEIGHT | 5.5 lbs |
POWER SUPPLY | Plug and play hub 120V, 60 Hz |
POWER WATTAGE | 8.5 W |
NOISE INDEX | 53 dB |
APPLICATION AREA | 107.6 – 161.5 sq. feet |
AIR VOLUME | 2179 cubic feet per hour |
FEATURES
- Remote control.
- Smart tech features
- Automatic air detection sensors
- Double fan system
- Time sleep function
- Multi-layered filtration systems
- Fragrance box to insert fragrance of choice
SAFETY PRECAUTIONS
-
Product is designed for use in houses or similar environments. Do not use outdoors.
-
Do not use device
a. Under high temperature,
b. Under high humidity,
c. In excessively dusty areas
We do not recommend using in the kitchen or bathroom as it is common for the above conditions to exist. -
a. Do use device near heating equipment e.g. oven, fan heater. Do not place or use device under direct sunlight
b. Do not use device near water/moisture or with wet hands -
Place the inlet and outlet are at least 30cm 1ft from other items. Do not cover these inlets with any items
For best use avoid using in fluctuating and varying temperatures and do not
use or spray aerosols/aromatherapy fumes before switching device on or while
device is on
The device cannot eliminate carbon monoxide or radon.
Mounting Instructions
A mounting bracket is supplied with the unit.
- Locate area on wall for mounting bracket between 2-5 feet from floor and ideally away from doors and corners.
- The bracket can be mounted directly into stud or dry wall with appropriate mounting hardware (not included)
- Once bracket is securely fastened to wall hang unit onto bracket and plug in.
HOW TO WORK THE DEVICE
DISPLAY PANEL
This display is touch sensitive, so it only requires a light touch. As can be seen for the image above the setting that is selecting is illuminated.
Start Up
After connecting the power cord to the device and plugging into outlet,
lightly press the On/Off button on the top left of the panel, to start the
purifier
To control air speed
Use the speed function button on the bottom left of the panel. There
are three modes of air speed 1) “sleep” 2) “low” 3) “fast” We recommend using
fast speed when using the device at irregular intervals. If you regularly use
the device low speed is suitable while sleep function is suitable for night
time or out of office hours.
Timing Function
You can either run this machine for 1 hour or 3 hours before the device goes
to sleep The timer button is on the bottom right of the panel.
UV Sterilization and Negative Ion
NOTE: the device is set to negative ion as a default. Therefore, when you
start the machine the negative ion function will be on. The device emits
negative ions for 20 minutes at a time with 5 minute intervals in between.
Automatic Air quality detection
There are three air quality detection indicators labelled “poor”,
“moderate”, and “good”. The device has a built-in sensor that the level of air
quality. When the air quality is bad, the device will automatically switch to
the fast speed mode. It takes about 3 minutes for the sensor to warm up and
acclimatize to the room once the device is turned on.
**Filter replacement Warning**
After 1500 hours of operating the filters will require replacement. The three
air quality indicators “poor”, “moderate”, “good” will flash at the same time.
There will also be an alarm that sounds. Once you have replaced the filter to
stop the alarms press the timer and speed buttons together for 5 seconds, this
will reset the system.
see removal of filter instructions below
Remote Control
The device also has a remote control that functions similarly to the panel.
To remove the filter
Disassemble the front panel
- Hold the top of the panel with you left hand.
- Place you right hand and the top edge of the front panel and pull the panel out to a 45-degree angle 3. Once at a 45-degree angle lift the panel upwards and out.
Disassemble the filter
- There are two tabs on either side of the filter
- Pull both tabs to remove the five in one filter
- Then slightly pull the different filter layers apart
To Replace the Filter
- Align the filter back into the slot.
- Make sure the tabs on the filter are to the front.
- Push the filter back into place.
- Replace front panel into bottom tabs and press to close.
PRODUCT MAINTENANCE
PROBLEM | POSSIBLE CAUSE | TROUBLESHOOTING |
---|---|---|
The unit is not working | Power cord is not plugged in or not working |
Plug in cord or check working of cord
Power button is not on| Press on/off button
The purification effect is poor| Air inlet/outlet is blocked| Clear
inlet/outlet of foreign objects and parts
Filter is too dirty| Clean and replace filters
Abnormal noise exists| Make sure all of the packaging is removed from
the device
| Check device for damage
| Check air inlet and outlet
| A fizz sound for the negative ion function is normal
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>