V I V O STAND-E-102B Electric Height Adjustable Dual Monitor Stand Instruction Manual

: October 30, 2023
: V I V O

Table of Contents

V I V O STAND-E-102B Electric Height Adjustable Dual Monitor Stand
PACKAGE CONTENTS
TOOLS NEEDED
ASSEMBLY STEPS
Option A: Dual Monitor Setup
Option B: Single Monitor Setup
Monitor Installation
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

V I V O STAND-E-102B Electric Height Adjustable Dual Monitor Stand

Electric Height Adjustable Dual Monitor Stand

This is an electrically height-adjustable dual monitor stand designed to hold most 20-32 inch screens. It has a weight capacity of up to 22lbs (10kg) per arm. The package contents include:

A (x1) Electric Stand
B (x1) Lower Clamp Bracket
C (x1) Upper Clamp Bracket
D (x1) Clamp Cable Clip
E (x1) Dual Arm
F (x1) Single Arm Bracket
G (x4) Arm Cable Clips
H (x2) VESA Plate
I (x1) Cable Sleeve
S-A (x4) M6x12mm Screw
S-B(x2) Screw Cap
S-C (x2) M3x8mm Screw
M-A (x8) M4x12mm Screw
M-B (x8) M5x12mm Screw
M-C (x8) M5 Washer
T-A (x1) 4mm Allen Wrench
T-B (x1) 6mm Allen Wrench

Usage Instructions:

Attach the Upper Clamp Bracket (C) to the bottom of the Electric Stand (A) using M6x12mm Screws (S-A) and a 4mm Allen Wrench (T-A).
For desktops between 10-55mm (0.40-2.15), align the key slots on Lower Clamp Bracket (B) with the screws on Upper Clamp Bracket (C). Pull Lower Clamp Bracket (B) down and lock the screws on Upper Clamp Bracket (C) in place with the 4mm Allen Wrench (T-A). For desktops between 50-85mm (2-3.35), remove the screws on Upper Clamp Bracket (C) and reassemble them to the lower set of holes using 4mm Allen Wrench (T-A). Align the key slots on Lower Clamp Bracket (B) with the screws on Upper Clamp Bracket (C). Pull Lower Clamp Bracket (B) down and lock the screws on Upper Clamp Bracket (C) in place with the 4mm Allen Wrench (T-A).
Clamp the stand assembly onto the desk. Press the Clamp Cable Clip (D) onto Upper Clamp Bracket (C).
If using a dual monitor setup, partially loosen screw on Dual Arm (E) with 6mm Allen Wrench (T-B) and slide Dual Arm (E) onto the post of Electric Stand (A).
Re-tighten screw on Dual Arm (E) with arm assembly at the top of the post using the 6mm Allen Wrench (T-B). Attach an Arm Cable Clip (G) onto each arm segment. Note: The final arm position will be determined in step 13.
If using a single monitor setup, remove a single arm segment and the cable clip from Dual Arm (E) using the 6mm Allen Wrench (T-B).
Loosely assemble the cable clip on Single Arm Bracket (F) using the 6mm Allen Wrench (T-B).
Attach the single arm segment to Single Arm Bracket (F) using the 6mm Allen Wrench (T-B). Note: This screw adjusts the joint tension. The tighter the screw, the more resistance there will be when pivoting the arm.
Re-tighten screw on Single Arm Bracket (F) with arm assembly at the top of the post using the 6mm Allen Wrench (T-B). Attach an Arm Cable Clip (G) onto each arm segment. Note: The final arm position will be determined in Step 13.

Note: Some hardware may not be used. Adult supervision is required as the product contains small parts that could be a choking hazard for children under 3 years of age.

SKU: STAND-E-102B

Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product.
https://vivo-us.com/products/stand-e-102b

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

help@vivo-us.com
www.vivo-us.com Chat live with an agent!
309-278-5303

WARNING!

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

WARNING: CHOKING HAZARD

SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

TOOLS NEEDED

SUPPORTED MONITOR RANGES :
Most 20” – 32” screens
DO NOT EXCEED WEIGHT CAPACITY.
22lbs
(10kg)per arm
Failure to do so may result in serious injury.

ASSEMBLY STEPS

STEP 1
Attach Upper Clamp Bracket (C) to the bottom of the Electric Stand (A) using M6x12mm Screws (S-A) and a 4mm Allen Wrench (T-A).
STEP 2
For desktops between 10-55mm (0.40”-2.15”), align the key slots on Lower Clamp Bracket (B) with the screws on Upper Clamp Bracket (C). Pull Lower Clamp Bracket (B) down and lock the screws on Upper Clamp Bracket (C) in place with the 4mm Allen Wrench (T-A).

For desktops between 50-85mm (2”-3.35”), remove the screws on Upper Clamp Bracket (C) and reassemble them to the lower set of holes using 4mm Allen Wrench (T-A). Align the key slots on Lower Clamp Bracket (B) with the screws on Upper Clamp Bracket (C). Pull Lower Clamp Bracket (B) down and lock the screws on Upper Clamp Bracket (C) in place with the 4mm Allen Wrench (T-A).

STEP 3
First, clamp the stand assembly onto desk. Press the Clamp Cable Clip (D) onto Upper Clamp Bracket (C)

Option A: Dual Monitor Setup

STEP 4
Partially loosen screw on Dual Arm (E) with 6mm Allen Wrench (T-B) and slide Dual Arm (E) onto the post of Electric Stand (A).
STEP 5
Re-tighten screw on Dual Arm (E) with arm assembly at the top of the post using the 6mm Allen Wrench (T-B). Attach an Arm Cable Clip (G) onto each arm segment.
Note: The final arm position will be determined in step 13.

Option B: Single Monitor Setup

STEP 6
Remove a single arm segment and the cable clip from Dual Arm (E) using the 6mm Allen Wrench (T-B).
STEP 7
Loosely assemble the cable clip on Single Arm Bracket (F) using the 6mm Allen Wrench (T-B).
STEP 8
Attach the single arm segment to Single Arm Bracket (F) using the 6mm Allen Wrench (T-B). Note: This screw adjusts the joint tension. The tighter the screw the more resistance there will be when pivoting the arm.
STEP 9
Re-tighten screw on Single Arm Bracket (F) with arm assembly at the top of the post using the 6mm Allen Wrench (T-B). Attach an Arm Cable Clip (G) onto each arm segment. Note: The final arm position will be determined in Step 13.

Monitor Installation

STEP 10
Attach VESA Bracket (H) to monitors using either M4x12mm or M5x12mm bolts (M-A,M-B) and Washers (M-C) along with a Phillips Screwdriver.
STEP 11
Slide monitors onto tilt joint located on the arm assembly. Lock VESA plate (H) in place with Screw Cap (S-B), M3x8mm Screw (S-C) and a Phillips Screwdriver. Adjust monitor height alignment by turning Screw Cap (S-B) by hand or using 6mm Allen
Wrench (T-B).
Note: If you are having an issue with a monitor tilting down once installed on the arm, refer to Step 17 to tighten down the tilt joint.
STEP 12
Connect the DC plug on the splitter cable into the base of Electric Stand (A). Connect USB coming from the desk control panel into the base of Electric Stand (A). Make sure the USB cord is ran outside of the cable clip. Refer to the frame manual to plug in the remaining cables.
STEP 13
Initial Setup Procedure:
Referring to the control panel instruction manual, ensure the panel display is set to adjust frame height (see the “Shift Device Display” section) and move your desk frame to a comfortable level for your normal sitting position. It is recommended to follow general ergonomic guidelines for working posture while considering your desk frame height. Store this position in memory setting 1.
Next, with the electric stand at its lowest height setting, loosen the arm bracket screw using the 6mm Allen Wrench (T-B) and manually adjust the arm assembly along the electric stand post until the top of the monitor screen is at eye level while in your normal sitting position. If this is not possible due to being taller or shorter than average, simply position the arm assembly at the very top or the very bottom of the electric stand post respectively. Re-tighten the arm bracket screw to secure the arm assembly in this position.
Note: You do not have to use the monitor at this height, but doing so reduces the amount of manual adjustment later on.
STEP 14
Setting Memory Positions:
Referring to the control panel instruction manual, ensure the panel display is set to adjust stand height. In your normal sitting position, move the stand until the monitors are at a comfortable level, switching between frame and stand adjustment on the panel display as necessary. It is recommended to follow general ergonomic guidelines for work posture while considering the optimal height of your monitors. Store this position in memory setting 1. Your desk and monitor height should both now be synced to memory setting 1.

Referring to the control panel instruction manual, move your desk frame and monitor to a comfortable standing position, switching between frame and stand adjustment on the panel display as necessary. Store these height locations to memory setting 2. Repeat this procedure for storing a third working posture in memory setting 3 if desired.

STEP 15
Route cables through Arm Cable Clips (G) and Cable Sleeve (I). Make sure there is enough slack in the cables and sleeve when the electric stand is at its tallest height. Use scissors to cut away excess cable sleeve length.
STEP 16
Adjust monitors as desired. The forward and backward tilt strength can be adjusted with the 6mm Allen Wrench (T-B).

Your workstation is now setup and ready to adjust both desk and monitor height between working positions at the press of a button. It can take some time to get used to monitor height adjustment between sitting and standing, and therefore slight adjustments to your monitor height memory settings are encouraged until you find the most ideal position for your specific working posture and individual needs, within reason of ergonomic principles.

Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us

Open Monday – Friday 7:00am – 7:00pm CST,
Our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

309-278-5303
AVG. RESOLUTION TIME (within office hrs): 5M 4S

www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within office hrs): < 15 M

help@vivo-us.com
AVG. RESPONSE TIME (within office hrs): 1HR 8M