V I V O DESK-E-100W White Electric Single Motor Desk Frame Instruction Manual
- October 30, 2023
- V I V O
Table of Contents
White Electric Single Motor
Desk Frame
Instruction Manual
DESK-E-100W White Electric Single Motor Desk Frame
SKU: DESK-E-100W
Scan the QR code with your mobile device or follow the link for helpful videos
and specifications related to this product.
https://vivo-us.com/products/desk-e-100b
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
| help@vivo-us.com
---|---
| www.vivo-us.com
Chat live with an agent!
| 309-278-5303
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual and do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly, or inappropriate use.
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND
ELECTRIC SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
- DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
- DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
- NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR SELLER TO REPLACE DAMAGED PARTS.
- NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE MADE CONTACT WITH LIQUIDS.
- ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
- OUTDOOR USE IS PROHIBITED.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
WARNING
PINCH POINT
DO NOT place hands on or near support bars. Moving parts can crush and cut.
Pinch points are created during lifting and lowering the worksurface. Failure
to follow these instructions may result in serious personal injury.
DO NOT EXCEED WEIGHT CAPACITY
Failure to do so may result in serious injury.
TOOLS NEEDED
ASSEMBLY STEPS **
**
STEP 1
Loosely assemble the Telescopic Cross Bar Set (A) making sure the locking
holes are facing up as shown below. Partially insert M6x8 bolts (J) into the
locking holes using Allen Wrench (T), making sure the Cross Bar is still able
to slide freely.
STEP 2
Attach Cross Bar (A) to both the Motorized Leg (B) and Non-motorized Leg (C)
using M6x10 bolts (K), making sure the locking bolts are still facing up on
the Cross Bar. Tighten with Allen Wrench (T).
STEP 3
Attach Side Brackets (D) to both ends of the frame using M6x10 bolts (K).
Tighten with Allen Wrench (T). 
STEP 4
Place a foot (E) on each leg as shown below. Attach each foot using M6x30 bolt
(L). Tighten with Allen Wrench (T).
STEP 5
FOR VIVO DESKTOP: Adjust frame width until the Side Bracket (D) holes
line up with the pre-drilled holes on the desktop. Adjust center crossbar
section until all M6x8 bolts (J) are able to make contact, then fully tighten
using Allen Wrench (T). To attach the desktop, refer to the manual included
with your desktop. Set aside x2 of the ST4.8×16 screws (H) for mounting the AC
Adapter (N).
FOR OTHER DESKTOP: Adjust the frame to the desired width while making
sure the overhang does not exceed 10″ on either side. Adjust center crossbar
section until all M6x8 bolts (J) are able to make contact, then fully tighten
using Allen Wrench (T). Mark and drill pilot holes to a depth of 3/8″ (10mm)
using a 1/8″ (3mm) bit where the Side Brackets (D) align on the desktop.
Secure the frame using ST4.8×16 screws (H) to the desktop. Set aside x2 of the
ST4.8×16 screws (H) for mounting the AC Adapter (N).
STEP 6
Insert one of the Sync Rod Hex Shafts (G) through the motor and into the
Motorized Leg (B).
NOTE: If the hex does not line up with the leg, temporarily plug the
Motorized Leg (B) and the AC Adapter (N) into the Controller (M) (see step 10
for details). Then, while pushing on the hex shaft, very briefly press the up
and down arrows (alternating between the two buttons so the legs will still be
even when assembled) until the shaft slides into the leg.
STEP 7
Loosen the preinstalled set screws on the Sync Rod Center Shaft (F) using
Allen Wrench (S). Slide the Sync Rod Center Shaft (F) onto the installed motor
Sync Rod Hex Shaft (G) as far as it will go. Then install the second Sync Rod
Hex Shaft (G) into the Sync Rod Center Shaft (F). Then slide the second Hex
Shaft into the Non-motorized Leg (C).
NOTE: If the hex does not line up with the leg, temporarily plug the
motorized leg (B) and the AC Adapter (N) into the Controller (M) (see step 10
for details). Then, while pushing on the shaft, very briefly press the up and
down arrows (alternating between the two buttons so the legs will still be
even when assembled) until the shaft slides into the leg. 
STEP 8
Center the Sync Rod Center Shaft (F) so it rest’s evenly on both Sync Rod Hex
Shafts (G). When in place, tighten the preinstalled set screws using the
smaller Allen Wrench (S).
Note: Be sure not to pull out the hex shafts from either leg.
STEP 9
Attach the Controller (M) to the desktop using ST2.9×15 screws (I), making
sure it is on the side of the Motorized Leg (B). 
STEP 10
Plug cables together as shown below. Tidy up cables using Cable Clips (P).
Attach AC Adapter (N) to desktop using ST4.8×16 screws (H), the Screw-on
Eyelets (Q), and 10″ Zipties (R) as shown below.
Note: A desk reset is required before use. Refer to the Controller User
Guide for operational instructions. Ensure there is enough slack in the cables
at the lowest and highest positions before use.
STEP 11
If necessary, adjust foot pads at the bottom of foot (E) to level the
desk.
CAUTION!
| Do not exceed desk weight limit.
---|---
| Keep area of vertical motion
free of obstacles.
| Keep weight on desk balanced for correct operation and longer life of
components.
| Leave enough slack in cables to allow for full range of vertical motion.
Failure to follow these instructions may result in property damage and/or
personal injury.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
Open Monday – Friday 7:00am –
7:00pm CST, our dedicated support team can offer immediate assistance with
rapid response times. If any parts are received damaged or defective, please
contact us. We are happy to replace parts to ensure you have a fully
functioning product.
| 309-278-5303| AVG. RESOLUTION TIME (within office hrs): 5M 45
---|---|---
| www.vivo-us.com
Chat live with an agent!| AVG. RESOLUTION TIME (within office hrs): < 15 M
| help@vivo-us.com| AVG. RESPONSE TIME (within
office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < lhr
– 83% within < 2hr
– 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
LAST UPDATED: 03/08/2022
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Electric Single Motor Desk Frame with Memory Controller – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>