SEVILLE CLASSICS WEB484 UltraGraphite Mobile Workbench

PARTS LIST

Please check the parts carefully according to the parts list. If you are missing any parts, please contact our customer service department.

PC

3-B| BOTTOM CROSSBAR| 1 PC| #20-7| DRAWER DIVIDER| 2 PCS

5-B| LEG PIECE| 2 PCS| #47| “L” BRACKET| 8 PCS

11| WHEEL WITH BRAKE| 2 PCS| #48-2| DRAWER LEFT SUPPORT| 1 PC

13| WHEEL W/O BRAKE| 2 PCS| #48-3| DRAWER RIGHT SUPPORT| 1 PC

18| DRAWER MAT| 1 PC| #50| SCREW I (M6 x 15L)| 48 pcs

19-2| DRAWER BASE PANEL| 1 PC| #40| SCREW E(M8 x 18L)| 4 pcs

20-1| DRAWER FRONT PANEL| 1 PC| #27-B| WASHER| 4 pcs

20-3| DRAWER LEFT PANEL| 1 PC|  | #15| SCREW B (M4 x 8L)| 30 pcs

20-4| DRAWER RIGHT PANEL| 1 PC| #21| SCREW DRIVER| 1 pc

20-5| DRAWER BACK PANEL| 1 PC| #25| WRENCH| 1 pc

ASSEMBLY INSTRUCTIONS

Tip: A magnetic screwdriver is included for your convenience. If using a power screwdriver, keep torque setting on LOW.

1. Step 1: Install (#5-B) Leg Piece.
   A: Open the package, and put the parts aside.
   NOTE: Leave the Solid Hardwood Board Top (#1) on cardboard

   • Attach the (#47) “L” Bracket to the (#5-B) Leg Piece, use (#50) Screw I to tighten.
   • Repeat Step A to install (#47) “L” Brackets to another one (#5-B) Leg Piece.
   • Tighten the all the screws after the (#47) Brackets are flush with the (#5-B) Leg Piece.

2. Step 2: Install (#48-2) Drawer Left Support, (#48-3) Drawer Right Support.

   • Attach the (#48-2) Small Drawer Left Support to the bottom of (#1) Solid Hardwood Board, line up the screw holes, use (#50) Screw I and (#21) Screwdriver to tighten.
   • Repeat this step to install (#48-3) Small Drawer Right Support.
     NOTE: Do not fully tighten the screws. This will help you make any adjustments for alignment.

3. Step 3: Install (#3-B) Bottom Cross Bar and (#11) Swivel Wheel with Brake & (#13) Swivel Wheel w/o Brake.

   • Attach the (#3-B) Bottom Cross Bar to the back of (#5) Leg Piece, line up the screw holes, use (#40) Screw E with (#27-B) Washer and (#25) Wrench to tighten.
   • After installing (#5-B) Leg Pieces, attach (#11) Swivel Wheel with Brake & (#13) Swivel Wheel w/o Brake to (#5-B) Leg Pieces, use Wrench (#25) to tighten.

4. Step 4: Turn the workbench right side up once you finish this step. Step the break of the wheel (#11) as the the side photo to stable the workbench.

5. Step 5: Install (#20-3 & #20-4) Left & Right Drawer Side Panels and (#20-5) Drawer Back Panel.
   Attach (#20-3 & #20-4) Left & Right Drawer Side Panels and (#20-5) Drawer Back Panel to the (#19-2) Drawer Base Panel. Line up the screw holes and use (#15) Screw B to tighten.
   NOTE: Make sure the hook slots on the (#20-5) Drawer Back Panel are facing inward.
   NOTE: Do not fully tighten the screws until next step had finish.

6. Step 6: Install (#20-6) Drawer Front Panel Support Plate Attach (#20-6) Drawer Front Panel Support Plate as the left arrow shows. Line up the screw holes and use (#15) Screw B to tighten.
   NOTE: Make sure the hook slots on the (#20-6) Drawer Front Panel Support Plate are facing inward.
   NOTE: Once you adjust all the parts in position, tighten all screws.

7. Step 7: Install (#20-1) Drawer Front Panel

   • Attach the Drawer Case to the (#20-1) Drawer Front Panel. Line up the screw holes and use (#15) Screw B to tighten.
     Note: Drawer’s maximum loading capacity is 30 lbs to avoid the unit from tipping when drawer is fully extended.

8. Step 8: Insert Drawer

   • Pull out the drawer sliders to full length, then attach and fit the Drawer to the inner track of the sliders and slide drawers in.
     NOTE: Make sure to remove the rubber guards on the hooks of the inner track before fitting the drawer in.
     Once you insert the drawers, tighten (#15) Screw B for (#48-2) Small Drawer Left Support and (#48-3) Small Drawer Right Support.

9. Step 9: Place (#18) Drawer Mat

   • Insert (#18) Drawer Mats to drawer before (or after) sliding drawer into bench.

10. Step 10: Install (#20-7) Drawer Divider

    • Insert Drawer Divider into the drawer. The solid wall of the divider should be facing the desired slot position.
    • Slide the divider towards the slot, then push down into the slots.
    • Repeat the above steps to assemble another Drawer Divider.
      NOTE: Dividers can be added to the drawer before or after finishing assembly.

How to Remove Dividers
Lift the Drawer Divider up and to the side to remove from the slot.

CAUTION: Potential Shock or Fire Hazard.
This unit is not intended for use in wet or potentially wet locations, such as showers, saunas, under or near fish tanks, sinks, etc.

UltraHD® Wood Top Care Instructions
Our tops are made with real wood, and while great care is taken to ensure consistent top color and graining, there may be natural variations between finished products. We hand-select the wood for every top to ensure the material is undamaged and naturally beautiful. If the wood top is received with excessive damage or splitting, Seville Classics will guarantee replacement of the top. Variations of color, and minor scratches in the clear coat finish will not be reason for replacement.

Restore Shallow Scratches or Chips
The wood surface of this product is finished with a polyurethane coat. If the wood top becomes chipped or scratched, a polyurethane coat can be reapplied to restore a smooth texture and protect from future damage.

• Please follow the manufacturer’s instruction on the product for application.

CONTACT INFORMATION

If you are missing any parts, have any questions, or need additional assistance in assembly, please contact our bilingual (English and Spanish) customer service department at:

• Seville Classics, Inc. 19401 Harborgate Way Torrance, CA 90501 USA Telephone: (800) 323-5565 within USA

• Fax: (310) 533-3899

• Hours: 9:00am – 4:30pm (Pacific Standard Time)
  E-mail: support@sevilleclassics.com

• Website & Online Store: www.sevilleclassics.com

Please visit our website or call and inquire about our additional UltraHD Line

UltraHD® Line

References

• Seville Classics

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>