V I V O STAND-V003KL Pneumatic Arm Dual Monitor Desk Mount Instruction Manual
- October 30, 2023
- V I V O
Table of Contents
STAND-V003KL Pneumatic Arm Dual Monitor Desk Mount
Instruction Manual
STAND-V003KL Pneumatic Arm Dual Monitor Desk Mount
SKU: STAND-V003KL
Scan the QR code with your mobile device or follow the link for helpful videos
and specifications related to this product.
https://vivo-
us.com/products/stand-v003kl
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
help@vivo-us.com
www.vivo-us.com
Chat live with an agent!
309-278-5303
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
TOOLS NEEDED
DO NOT EXCEED WEIGHT
CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
Loosen the screws on Clamp (F) using the 4mm Allen Wrench (T-A) and separate
into Upper Clamp (F1) and Lower Clamp (F2).
STEP 2
OPTION A: Clamp Installation
Assemble Upper Clamp (F1) to Pole (E) using the M6x16mm Screws (S-B) and 4mm
Allen Wrench (T-A). Remove the adhesive backing on Soft Pad (J) and place it
onto Upper Clamp (F1).| OPTION B: Grommet Base Installation
Cut Soft Pad (J) along the indentations. Remove the adhesive backing on Soft
Pad (J) and place it onto Grommet Plate (H).
---|---
| 
For thinner desktops, re-attach Lower Clamp (F2) to Upper Clamp (F1) and
tighten the screws using the 4mm Allen Wrench (T-A). For thicker desktops,
disassemble Lower Clamp (F2) using a Phillips screwdriver as shown below. Flip
the L-bracket over and reassemble. Then re-attach Lower Clamp (F2) to Upper
Clamp (F1) and tighten the screws using 4mm Allen Wrench (T-A). Secure Clamp
(F) to the desktop.| Using a 10mm (⅜”) drill bit, drill through the desktop at
least 2” away from the edge. Disassemble Lower Clamp (F2) using a Philips
screwdriver. Set aside all parts except for Clamp Bolt (F3). Assemble Pole (E)
with Grommet Base (F) to the desktop using Support Plate (I) and Clamp Bolt
(F3) as shown below.
| 
STEP 3
While holding Dual Arm (A) and Arm (B) closed, cut the shipping tie and gently
release.
STEP 4
Loosen the screw on the back of Dual Arm (A) and Arm (B) using 6mm Allen
Wrench (T-B). Slide Dual Arm (A) and Arm (B) onto Pole (E) and retighten
screws. Secure Cable Clip (L) to Pole (E).
STEP 5
Place Laptop Arms (G) underneath each side of Laptop Tray (C), aligning square
holes in arms with the edge and long slot on each side. Insert Clips (K)
through top to secure arms, making sure all four locks on each clip are
engaged with the square holes in arms.
STEP 6
Attach Laptop Tray (C) to 75mm and 100mm holes on VESA Plate (D) using M4x8mm
Screws (S-A) and a Phillips screwdriver.
STEP 7
Slide VESA Plate (D) with Laptop Tray (C) onto Arm (B) and secure using
Thumbscrew (S-C).
STEP 8
Attach VESA Plates (D) to the back of the monitors using Screws (M-A through
M-D) and Washers (M-E).
If needed, use Spacers (M-F).
STEP 9
Slide VESA Plates (D) with monitors over bracket on Dual Arm (A). Secure using
Thumbscrews (S-C).
Release locks on underside of Laptop Arms (G). Extend Laptop Arms (G), place
the laptop on Laptop Tray (C), then adjust Laptop Arms (G) to the width of the
laptop. Engage locks to secure the laptop. If using a thicker laptop, turn the
front bumpers to the upward position for additional support. 
STEP 10
Remove bottom covers from Dual Arm (A) and Arm (B) by sliding them off.
Organize cables and re-attach covers.
STEP 11
Adjust tilt support using 6mm Allen Wrench (T-B). Store Allen Wrenches (T-A
and T-B) in Cable Clip (L).
Adjust as desired. Adjust the tension in gas spring arms using 6mm Allen
Wrench (T-B).
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
309-278-5303 AVG. RESOLUTION TIME (within office hrs): 5M 4S
AVG. RESOLUTION TIME (within office hrs): < 15 M www.vivo-us.com Chat live with an agent!
help@vivo-us.com
AVG. RESPONSE TIME (within office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www
.vivo-us.com
LAST UPDATED: 10/10/2022
REV1
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Pneumatic Arm Dual Monitor and Laptop Desk Mount – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>