V I V O MOUNT-G200B2 Dual Monitor Wall Mount Instruction Manual
- October 30, 2023
- V I V O
Table of Contents
Dual Monitor Wall Mount
Instruction Manual
SKU: MOUNT-G200B2
https://vivo-us.com/products/mount-
g200b2
MOUNT-G200B2 Dual Monitor Wall Mount
Scan the QR code with your mobile device or follow the link for helpful videos
and specifications related to this product. https://vivo-us.com/products
/mount-g200b2
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this
product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We cannot be liable for damage or injury caused by
improper mounting, incorrect assembly or inappropriate use.
PACKAGE CONTENTS
TOOLS NEEDED
DO NOT EXCEED WEIGHT CAPACITY
Failure to do so may result in serious injury.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR CEILING CONSTRUCTION. USE WOOD
STUDS TO MOUNT. We include mounting for concrete ceilings as well. If unsure,
please contact us at vivo-us.
com, email at help@vivo-us.com, or call us at
309-278-5303.
ASSEMBLY STEPS
STEP 1 (Option A)
Wood Stud Installation
Hold Mount (A) in place along the stud and mark mounting holes using a pencil.
Using a 3/16” (4.5mm) drill bit, drill holes in marked locations approximately
2.2” (55mm) deep. Secure Mount (A) to the wall using ST6.3x55mm Screw (W-A)
with M6 Washers (W-C) and a Phillips screwdriver.
STEP 1 (Option B)
Concrete/Brick Wall Installation
Hold Mount (A) to mounting surface and mark drill holes with pencil. Drill
2.4” (60mm) deep holes using a 3/8” (10mm) drill bit. Insert Anchors (W-B)
into predrilled holes and secure Mount (A) to the wall using ST6.3x55mm Screw
(W-A) with M6 Washers (W-C) and a Phillips screwdriver.
STEP 2
Insert Upper Cover (J) and Lower Cover (K) into the mounting holes on Mount (A).
STEP 3
Remove the nut from the bottom of VESA Plate (B) using Wrench (T-C) and
loosen the top two nuts, leaving 3mm of threads exposed.
STEP 4
Assemble Arms (F) to Bracket (E) with Bracket Cover (G) using M6x30mm Screws
(S-A) and 4mm Allen Wrench (T-A).
STEP 5
Slide VESA Brackets (D) onto Arms (F). Insert End Caps (H) into the ends of
Arms (F). Secure End Caps (H) using M5x10mm Screws (S-B) and a Phillips
screwdriver. Lock VESA Brackets (D) in place using 4mm Allen Wrench (T-A).
Assemble Cable Clips (I) to Arms (F).
STEP 6
Assemble Bracket (E) to VESA Plate (B) and Handle (C) using M5x16mm Screws
(S-C) and M5 Washers (S-D) with a Phillips screwdriver.
STEP 7
Slide VESA Plate (B) onto Mount (A) and tighten the top two nuts using Wrench
(T-C).
Insert the bottom nut onto VESA Plate (B) and tighten with Wrench (T-C).
STEP 8
Insert Screws (M-A or M-B) with D5 Washers (M-C) into the top two holes of
your monitor, leaving 3mm of space. Slide the monitors onto VESA Brackets (D)
and insert Screws (M-A or M-B) with D5 Washers (M-C) into the bottom holes of
your monitor. Tighten all screws with a Phillips screwdriver.
STEP 9
Adjust the tilt on VESA Brackets (D) using 6mm Allen Wrench (T-B).
STEP 10
Level the monitors by adjusting the nuts on VESA Plate (B) using Wrench (T-C).
STEP 11
Adjust the tension in Mount (A) using 6mm Allen Wrench (T-B). Rotate clockwise
to decrease tension, and counter clockwise to increase tension.
STEP 12
Route cables through Cable Clips (I) and the cable management clips in Mount
(A).
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.
| 309-278-5303 | AVG. RESOLUTION TIME (within office hrs): 5M 4S |
|---|
www.vivo-us.com
Chat live with an agent!| AVG. RESOLUTION TIME (within office hrs): < 15 M
****help@vivo-us.com| AVG. RESPONSE TIME (within
office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT:
www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Pneumatic Dual Monitor Wall Mount – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>