V I V O STAND-V101Q Pneumatic Arm Single Ultrawide Monitor Desk Mount Instruction Manual
- October 30, 2023
- V I V O
Table of Contents
V I V O STAND-V101Q Pneumatic Arm Single Ultrawide Monitor Desk Mount
Instruction Manual
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
ASSEMBLY STEPS
STEP 1 (Option A)
Clamp Installation
Secure Upper Clamp (E) to the underside of Base (D) using M6x10mm Flathead
Screws (S-B) and 4mm Allen Wrench (T-B). Remove adhesive backing and apply
Pads (K) to the underside of Base (D).
Connect Lower Clamp (F) to the front of Upper Clamp (E) using M6x10mm Screws (S-B) and 4mm Allen Wrench (T-B). For desktops 10-55mm (3/8” to 2 1/4”) thick, use top holes on Upper Clamp. For desktops 50-85mm (2” to 3 3/8”) thick, use the bottom two holes.
Secure clamp assembly to desktop by tightening the hand bolt. Affix Cable Clamp Clip (G) to the back of clamp assembly.
STEP 1 (Option B)
Grommet Installation
Insert Carriage Bolt (S-A) into Grommet Plate (H) and secure to underside of
Base (D) using M6x10mm Flathead Screws (S-B) and 4mm Allen Wrench (T-B).
Peel back adhesive backing and apply Pads (K) to underside of Base (D).
Place base assembly over grommet hole in desktop and place Support Plate (I) and Knob (J) on the end of Carriage Bolt (S-A). Tighten Knob (J) to secure.
STEP 2
Place Lower Arm (B) onto Base (D) and secure by tightening set screw with 3mm Allen Wrench (T-A). Install Upper Arm (A) on Lower Arm (B) and tighten set screw with 3mm Allen Wrench (T-A) to secure.
STEP 3
Secure VESA Plates (C) to back of monitors using appropriate Screws (M-A thru M-D), M6 Washers (M-E), and 6mm Allen Wrench (T-C). Use Spacers (M-F) for curved monitor.
Flat Back Monitors
Curved Monitors
STEP 4
Place monitor with VESA Plate (C) onto Upper Arm (A) and secure with M6x12mm Thumbscrew (S-C).
STEP 5
While holding Upper Arm (A) in the horizontal position, adjust the gas spring tension using 6mm Allen Wrench (T-C).
Adjusting Tension
Decrease Strength – If the arm raises up, turn the adjustment screws clockwise until it holds the monitor in a horizontal position.
Increase Strength – If the arm does not have enough movement, turn the adjustment screws counterclockwise.
CAUTION
To avoid damage to the monitor and mount, always keep the arm in a horizontal
position while making adjustments.
Cable Management Covers
Lower Arm (B):
- Slide cover forward to remove.
- Place cables in cover.
- Connect inner tabs to clips on Lower
Arm (B) arm to secure in place.
Upper Arm (A):
- Pull tabs outward on lower portion of cover.
- Pull upper tabs outward to fully remove cover.
- Place cables in cover.
- Re-install by snapping upper tabs in place, then snap lower tabs on to fully secure.
Adjustments
Adjust monitor placement as desired. Allen Wrenches (T-B, T-C) can be stored in Cable Clamp Clip (G) for future adjustments.
Love your new VIVO setup and want to share?
Tag us in your photo ! @vivo_us
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
Scan the QR code with your mobile device or follow the link for helpful
videos and specifications related to this product. Instruction Manual
https://vivo-us.com/products/stand-v101q
309-278-5303
AVG. RESOLUTION TIME (within office hrs): 5M 4S
www.vivo-us.com
Chat live with an agent! AVG. RESOLUTION TIME (within office hrs): < 15 M
help@vivo-us.com
AVG. RESPONSE TIME (within office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Pneumatic Arm Single Ultrawide Monitor Desk Mount – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>