AGA 680KCD Rayburn 600 Series Oil Fired Cooker User Manual
- October 30, 2023
- AGA
Table of Contents
AGA 680KCD Rayburn 600 Series Oil Fired Cooker
Product Information
The product is an AGA cooker. It is a kitchen appliance that uses heat stored in cast iron to cook food. The product is designed to be positioned between base units, onto an empty wall or going into an alcove or recessed area. The cooker is positioned using wheels and has specific dimensions, weights, and clearances that can be found on pages 27-29 of the manufacturer’s instructions.
Our shop will discuss this form with you while you are placing your order. If necessary you are welcome to take the form away and discuss the points raised with your contractors. If you take the form away with you, please return the completed copy to your AGA store at your earliest convenience. This will assist us with finalizing your installation.
Product Usage Instructions
Before installation, please discuss the AGA cooker with your contractors and ensure that you complete the form provided in the manual. If you take the form away with you, please return the completed copy to your AGA store at your earliest convenience. This will assist us with finalizing your installation.
Customer Reference
- Site Address: _____
- Postcode: _____
- Customer Name: _____
- Telephone No: _____
- Mobile No: _____
- Email: _____
- Key Contact for Site: _____
- Key Contact No: _____
PRE-INSTALLATION CHECKLIST
| Questions| Y| N| Additional Information
---|---|---|---|---
Access and parking| Can the property be accessed by a 7.5 ton lorry with a
tail lift 2415mm (8ft 3in) wide?
Are there any special permissions or permits required?
| | |
Route for delivery| Is there a clear route into the kitchen?
The minimum gap needed is 750mm through doors and hallways.
Please give details or any steps, gravel areas, grass areas, uneven surfaces, obstacles, tight turns.
If you have any concerns about the access route please contact your local AGA store as soon as possible.
| | |
Route for delivery| Is any floor protection needed?
Will there be any additional man power on site when we arrive?
| | |
Floor| What flooring is under the cooker position?
The cooker is positioned using wheels. Please lay your flooring before the cooker is fitted or fit a suitable plinth to ensure the base and flooring in the room are level with each other.
The flooring must be capable of supporting the weight of the cooker.
The cooker base dimensions, weights and clearances can be found on pages 27-29 of the manufacturer’s instructions
| | |
Position| Will the cooker be positioned between base units?
Will the cooker be positioned onto an empty wall? If so please ensure this is marked to enable us to correctly position the cooker.
Will the cooker be going into an alcove or recessed area? If so, electrical switches cannot be located above or behind the cooker. They must be outside of the recess following the distances advised in our instructions.
Is there space for a 3mm gap to be left each side of the cooker top plate?
Is there space for a 60mm gap to be left above the lid handles to allow for opening?
Is the cooker going against a side wall?
If so additional clearances will be needed
The cooker base dimensions, weights and clearances can be found on pages 27-29 of the manufacturer’s instructions
| | |
---|---|---|---|---
Rear Wall| Is the rear wall clear of pipes, wires, drains and other
services?
The rear wall must be clear of any obstructions.
How much gap do you need left behind the cooker position?
The minimum 10mm gap will be left between the top plate and finished surface behind. However, if you will be tiling or fitting anything behind afterwards we will need to know how much extra space will be required. The minimum 10mm gap must be left open and uncovered.
More details on this are shown on page 29 of the manufacturer’s instructions
| | |
Worktop| The cooker hotplate height is 910mm off the finished floor. Will
your surrounding surfaces match this height?
The cooker dimensions can be found on page 27 of the manufacturer’s instructions
| | |
Electrics| Where are you planning on positioning your electrical
connections?
The AGA requires 2 x 13amp connections within 2m of the cooker and in the same room. The first must be a switched fuse spur. The second can either be a switched fused spur or a 3 pin plug socket. These must not be above or behind the cooker and must be accessible.
Your electrician may connect these into connection points near to the cooker. If connection points are required, these must be either within 1.8m of the rear right bottom corner or 0.9m of the rear left hand bottom corner. The connection points can be behind the AGA as long as they are lower than 450mm from the finished floor.
Full details of this can be found on page 30 of the manufacturer’s instructions
| | |
Please provide any additional information which may be relevant to the
delivery or installation of the appliance
Your instructions can be found by following this link: https://www.agaliving.com/contact-support/user-guides/all
Occasionally certain circumstances may dictate that we will be unable to deliver your product using our standard delivery service. Should an external specialist team be required we will advise you in advance of any additional costs you may incur before we proceed with your delivery.
**** A copy of this delivery and installation checklist should be returned to your store at the time of placing your order. Please retain a copy to assist you with preparing for your AGA installation.
**** If you have any queries once your order has been placed please feel free to contact your local AGA store for further assistance.
**** If a delay is required to your installation date we need a minimum of five working days’ notice before the agreed date. Failure to provide this notice may incur a charge.