MIPRO BC-100 Conference Microphone Bases User Guide

: June 6, 2024
: MIPRO

Table of Contents

Part Names
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BC-100 Conference Microphone Bases
User Guide

Conference Microphone Bases

Part Names

All rights reserved. Do not copy or forward without prior approvals of MIPRO. Specifications and design are subject to change without notice. YM 021/12
This Confidential document is for the purposes of repairing MIPRO products only.
It is forbidden to modify, add, sell, print, copy, improperly use or offer to third parties. Otherwise, MIPRO will reserve the right to proceed with legal action
Conference Microphone Bases

Charging Connector & Indicators

Balanced 3 pin XLR Connector
Microphone
Selection Switch
Gooseneck Microphone Connector (4 pin)
LCD Panel
Power Button
ACT Sync Window
MODE Button
SET Button
TALK Indicator
TALK or MUTE Button
Transmitting Antenna
Boundary Microphone Grill
Battery Level Panel
Base Cover Latch
Base Cover
Battery Compartment

II. Battery Insertion
1. Turn Base Cover Latch 15 180° to loosen the base cover. Push and slide down Base Cover ® according.

All rights reserved. Do not copy or forward without prior approvals of MIPRO. Specifications and design are subject to change without notice. YM 021/12
Insert a charged 18500 type lithium according to its correct polarity.
3. Agr a push up «he Bas cover band .turn the latch P180° for secured closure. Push and hold Power Button O for 2 seconds to power on.

III. How to Charge

Plug the charger into the Charging9 Connector of the device and an AC outlet.
Charging still red indication).
Fully (still green indicator).
If the indicator doesn’t glow after both ends are plugged in, check the rechargeable battery is inserted correctly.
Be sure to use the supplied charger, and the input voltage should not be over the specified value.
Caution: Turn off the power when the device is not in use. Remove the battery if the device will not be used for an extended period.

VI. BC-24T/ BC-58T/ BC-100T Operating Instructions

Wireless Installation:
(A) Insert a MIPRO gooseneck microphone before powering on to avoid potential noise.
(B) Align the connectors and insert the microphone properly and secure tightly by turning counterclockwise.
(C) Turn clockwise to loosen the microphone.

Insert the gooseneck microphone into it. the connector, and then power on.
Conference Microphone Bases Insert the gooseneck microphone into it. the connector, and then power on.

(E) Power on and press down the TALK button to talk (recessed with a green indicator).
(F) To mute, press the MUTE button. After use, be sure to turn off the power. Remove the battery if the device won’t be used for an extended period.
2. Wired Installation:
(A) Press the TALK button to speak.
The indicator glows in green. Press the MUTE button to mute(Same operation as the wireless installation.)
(8) Connect the base and apply device with an XLR to XLR cable (not supplied) provided phantompowerXLR to XLR cable emove the cable’ if the device won’t be used
for an extended period. V. BC-100 Operating InstructiO°s
1. Wired Boundary Microphone: Q 7.
(A) Plug one end of an XLR to Xlccable into the XLR balanced connector on pie back panel. (
B) Switch the Microphone. Selection Switch to the “Boundary in” polygon.
(C) Press the TALK button to speak. die indicator glows in green. Press the Mt button to mute.
(D) Connect the cable to the XLR connector of the amplifier/mixer which prides phantom power.
Disconnect if the XLVonnector will not be used for an extended period.
All rights reserved. Do not copy or forward without prior approvals of MIPRO. Specifications and design are subject to change without notice. YM 021/12

Wired Installation:
(A) Plug one end of an XLR to XLR cable into the XLR balanced connector on the back panel. (B) Switch the Microphone Selection switch to the “Mic in” position.
(C) Press the TALK button to speak. The indicator c9tows in green. Press the MUTE button to mute. .,;s (Same operation as th0,43oundary microphone.
(D) Connect the cable to the XLR connector of the amplifier/mixer which provides phantom power. Disconnect if, the XLR connector will nOte i used for ark‘tended period.

VI. Operating Instructions
1. BC-24T/ BC-58T :
(A) Power On/Off: Press & hold the power button for two seconds to power on or power off the device. The LED lights after the device are powered on.
(B) Battery level indicators: Recommend charging when a single red indicator remains. Power shutdown automatically when battery voltage too low

2.BC-100T
power on/off
(1) Press and hold the power button for two,seco seconds to power on or power off the device. C),
(2) The LCD screen displays OFF… during powering off.
(B) Battery level indicators: Recommend charging once level falls to 10% and the screen flashes. The device will power off automatically with an OFF message once the power level falls too low.

Conference Microphone Bases
(C) LCD Screen

18. Functions Displays
19. Displays Parameters
20. Battery Level Meter

(D) Press the MODE button @ to access all the
(E) Press the SET button @ once to denote a change.
The existing parameter starts flashing. Press the SET button a second time to change the Programmed parameters.

(F) Group(GRP) / Channel (CH) /Frequency (FREQ.) are synced from the receiver and cannot be changed.

(G) AF Gain Setting:

AF Gain can be changed from, 12dB –120dB, in 6B steps,
Press the MODE button to access the AF GAIN parameter. Press the button to change. To save press the MODE button or until fashing sons.
The higher the gain is, the lower the input signal of dynamic range will be and it will increase noise and feedback chances.
Set AF Gain to -12B for guitar.
odb is my factory default setting.

(H) RF Power Setting:
(1) RF Power can be changed to RF-HI or RF-LOW.
(2) Press the MODE button to access RF POWER parameter. Press the SET button, the parameters start flashing. Press the SET button again, the parameter will change circularly. Press the MODE button to save or the parameter saves automatically when flashing stops.

(I) MUTE MODE Setting:

MUTE MODE can be changed to MANUAL or DISABLE.
Press the MODE button to access the MUTE MODE parameter. Press the SET button, the parameters start flashing. Press the SET button again, the parameter will change circularly.? Press the MODE button to save or the parameter saves automatically wheb9 flashing stops.
MANUAL mode indicates MUTE button can be muted.
DISABLE mode indicates MUTE button cannot be muted.

(J) LOCK Setting:

LOCK can be changed to LOCK or UNLOCK.
Press the MODE button to access the LOCK parameter. Press the SET button, the 4 parameters start flashing. Press the SET button again, the parameter will change circularly. Press the MODE button to save or the parameter saves automatically when flashing stops.
LOCKED mode indicates all the parameters cannot be changed and the power button cannot work. Press the SET button and the IOC)\- screen displays LOCKED.
Repeat the same procedures to change back to UNLOCK mode. UNLOCK mode indicates power is operational and the parameters can be changed.

(K) Error codes:

ERR no01-Channel wasn’t programmed or internal data error.
ERR no02-0Testing only.
ERR no03—The set frequency exceeds the upper band. The microphone frequency will not be changed but it can be operated as long as the power switch is turned on again.
ERR no04-The set frequency exceeds the lower band. The microphone frequency will not be changed but it can be operated as long as the power switch is turned on again.

(L) GROUP CHANNEL are internal programmed channels.
.m) CHANNEL displays only (GROUP is not shown) Zip indicates a user-defined frequency synced from 0 receivers and it only can be changed via PC.
VII. Notes

Refer to the actual product in the event of product description discrepancy.
Frequency range and maximum deviation comply with the regulations of different countries.

Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:
To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. (Example – use only shielded interface cables when connecting to computer or peripheral devices).
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of0.5CM between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The antennas used for this transmitter must be installed to provide a separation distance of at leastQ.5cm from all persons and must not be co- located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, ar6 (2) This device must accept any interference receive0> including interference that may cause undesired, 7 _ \U• operation. IC \-\ Industry Canada Statement a..0° This device complies with Industry Canada RSS-247 standard, Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 2 cm between the radiator and your body.
Disposal
Dispose of any unusable devices or batteries responsibly and in accordance with any applicable regulations. Disposing of used batteries with domestic waste is to be avoided! Batteries / NiCad cells often contain heavy metals such as cadmium(Cd), mercury(Hg), and lead(Pb) that make them unsuitable for disposal with domestic waste. You may return spent batteries/ accumulators free of charge to’ recycling centers or anywhere else %1/4batteries/accumulators are sold.
By doing so, you contribute to the 00 o66- conservation of our environment!

MICROPIAINE PROFESSIONALS
MIPRO Electronics Co., lid
Headquarters: No. 814, Beigang Rd.,
Chiayi City 600079, Taiwan
Tel : +886.5.238.0809
Fax : +886.5.238.0803
www.mipro.com.tw
mipromipro.com.tw
All rights reserved. Do not copy or forward without prior approvals of MIPRO. Specifications and design are subject to change without notice. YM 021/12