LaMotte Pro-9 Tes Tabs Instructions

LaMotte Pro-9 Tes Tabs Instructions

Tes Tabs limitation Instruction

• Read the instructions before testing.
• Press button to turn meter ON and OFF
• Quickly press button twice to skip a test.
• Cap the tubes securely to prevent leaks.
• Do not interchange color-coded caps.
• Dry the tubes before placing them in the chamber.
• Rinse tablet crusher after each use. Brush and rinse tubes, caps and tablet crusher after testing.
• Allow the tubes to dry before returning them to the case.
• The tube specified in the test procedure must be used.
• Use only LaMotte reagents. Cap securely.
• If unit should auto-off during testing, rinse and fill a tube. Repeat Blank and return to testing.
• Cap tube to eliminate stray light

WARNING! This set contains chemicals that may be harmful if misused. Read cautions on individual containers carefully. Not to be used by children except under adult supervision.

Send pool or spa test results from the Color Q 2x through Bluetooth to the ® Water Link Solutions App for chemical recommendations and dosage amounts.
Go to www.lamotte.com/pool to learn more about the Homeowner and Pool ® Professional Water Link Solutions water analysis programs.

Blank

1. Fill sample bottle (0688) with water sample. Replace cap.
2. Fill clean tube (0205) to the 5 mL line with water sample. Cap tube with blue cap.
3. Insert tube into the ColorQ 2x.
4. Press button to turn meter on . When “Blank” appears press button to “Blank” the meter, and go to Free Chlorine (FCL). Remove tube.

*Reagent is a potential health hazard.
****
READ SDS: lamotte.com

Emergency information:  Chem-Tel USA 1-800-255-3924 Int’l, call collect, 813-248-0585

FCL/Br

1.  Add 1 DPD 1 IG Tablet to same tube.

2. Cap tube with blue cap. Shake for 10 seconds. Invert 5 times to mix. Insert tube into the ColorQ 2x.

3. Press button to read “FCL” Free Chlorine.
   NOTE: to read as Bromine, press button past “FCL” and “TCL” to “Br”.

4. Press button to go to “TCL” Total Chlorine. Remove tube

TCL

1. Remove cap from reacted FCL (Free Chlorine) tube.
2. Add 1 DPD 3 IG Tablet. Cap tube with pink cap. Shake for 10 seconds. Invert 5 times to mix.
3. Insert tube into the Color Q 2x.
4. Press button to read “TCL” Total Chlorine.
5. Press button past “Br” to “pH”. Remove tube.

pH

1. Fill a clean tube (0205) to the 5 mL line with water sample.
2. Add 1 pH PHENOL RED Tablet. Crush with tablet crusher.
3. Cap tube with red cap. Invert 3 times to mix. Insert tube into the Color Q 2x.
4. Press button to read “pH” pH. Remove tube.

Alk

1. Press button to go to “Alk” Total Alkalinity.
2. Fill a clean tube (0205) to the 5 mL line with water sample.
3. Add 1 ALK 2X IG Tablet. Crush with tablet crusher.
4. Cap tube with green cap. Invert 10 times to mix. Insert tube into the ColorQ 2x.
5. Press button to read “Alk” Total Alkalinity. Remove tube.

Ca Hard

1. Press button to go to “Ca Hard” Calcium Hardness.
2. Fill a clean tube (0205) to the 5 mL line with water sample.
3. Add 1 CA HARD 2X IG tablet. Crush with tablet crusher. Cap tube with purple cap.
4. Invert 3 times to mix. Insert tube into the ColorQ 2x.
5. Press button to read “Ca Hard” Calcium Hardness. Remove tube.

CYA

1. Press button to go to “CYA” Cyanuric Acid.
2. Fill a clean tube (0206) to the line with water sample.
3. Add 1 CYANURIC ACID IG tablet. Crush thoroughly with tablet crusher. Cap tube with grey cap.
4. Invert 3 times to mix. Allow tube to sit for TWO minutes.
5. Do not mix. Insert tube into the ColorQ 2x.
6. Press button to read “CYA” Cyanuric Acid. Remove tube

Cop

1. Press button to go to “Cop” Copper.
2. Fill a clean tube (0205) to the 5 mL line with water sample.
3. Add 1 COPPER IG tablet. Crush with tablet crusher. Cap tube with blue cap.
4. Invert 3 times to mix. Allow tube to sit for TWO minutes.
5. Invert 1 times to mix. Insert into the ColorQ 2x.
6. Press button to read “Cop” Copper. Remove tube.

Ir

1. Press button to go to “Ir” Iron.
2. Fill a clean tube (0205) to the 5 mL line with water sample.
3. Add 1 IRON IG Tablet. Crush with tablet crusher. Cap tube with blue cap.
4. Invert 3 times to mix. Insert into the ColorQ 2x.
5. Press button to read “Ir” Iron. Remove tube.

big

1. Press button to go to “big” Biguanide.
2. Fill a clean tube (0205) to the 5 mL line with water sample.
3. Add 5 drops of BIGUANIDE TEST SOLUTION. Cap tube with blue cap.
4. Invert 3 times to mix. Insert tube into the ColorQ 2x.
5. Press button to read “big” Biguanide. Remove tube.

bsh

1. Press button to go to “bsh” Biguanide Shock.
2. Fill a clean tube (0205) to the 5 mL line with water sample.
3. Add 1 SHOCK PEROXIDE IG Tablet. Crush with tablet crusher. Cap tube with blue cap.
4. Invert 3 times to mix. Allow tube to sit for TWO minutes.
5. Invert once to mix. Insert into the ColorQ 2x.
6. Press button to read “bsh” Biguanide Shock. Remove tube.
7. Press button to return to blank meter or hold button until is displayed.
   

References

• LaMotte Company :: Water Quality and Analytical Testing Equipment
• LaMotte Company :: Water Quality and Analytical Testing Equipment
• LaMotte Pool and Spa Water Testing Products

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>