YATO YT-82451 Transformer Soldering Gun Instruction Manual

YATO YT-82451 Transformer Soldering Gun

Product Information

The PL LUTOWNICA TRANSFORMATOROWA or GB TRANSFORMER SOLDERING GUN is a tool designed for soldering metals with tin and lead binders for soft soldering. It has a maximum working time of 12 seconds and requires a break of at least 48 seconds before continuing work. The tool comes complete with spare soldering tips, rosin, and soldering tin.

The soldering gun has the following technical specifications:

Parameter| Catalog Number| Rating Voltage| Rating Frequency| Power| Tip Temperature| Work Mode| Dimensions (L x W x H)| Weight| Electric Insulation Class
---|---|---|---|---|---|---|---|---|---
Unit of Measurement| –| V~| Hz| W| °C| –| mm| kg| –
Value| YT-82451| 230 – 240| 50| 200| 70 – 200 / 201 – 350 / 351 – 500| S2 20% 12s / 48s| 185 x 185 x 55| 0.92| II

Product Usage Instructions

Before using the soldering gun, read the complete instruction manual and keep it for future reference. The supplier will not be held responsible for any damage and injuries that occur as a result of inappropriate use of the tool or failure to observe safety regulations and recommendations specified in the instructions.

To use the soldering gun:

1. Ensure the tool is not connected to the power supply.
2. Insert the soldering tip into the gun’s enclosure.
3. Insert the bulb and switch into the enclosure.
4. Connect the cable with the plug to the gun.
5. Connect the cable’s contact plug to the power supply.
6. Use the temperature control to set the desired tip temperature.
7. Solder metals with tin and lead binders for soft soldering, making sure not to exceed the maximum working time of 12 seconds and taking a break of at least 48 seconds before continuing work.

After use, turn off the soldering gun and disconnect it from the power supply. The tool does not require any assembly or maintenance.

Safety Instructions

Repairs to the tool should only be carried out by authorized centers using original replacement parts. This ensures proper safety when using the tool. The mounting of equipment can only be carried out when the tool is disconnected from the power supply. Do not use the tool for continuous work. Only use it for its intended purpose and follow all safety regulations and recommendations specified in the instructions.

OVERVIEW

1. enclosure
2. soldering tip
3. bulb
4. switch
5. cable with plug
6. temperature control

• Read the operating instruction
• Wear protective goggles
• Second class of insulation

This symbol indicates that waste electrical and electronic equipment (including batteries and storage cells) cannot be disposed of with other types of waste. Waste equipment should be collected and handed over separately to a collection point for recycling and recovery, in order to reduce the amount of waste and the use of natural resources. Uncontrolled release of hazardous components contained in electrical and electronic equipment may pose a risk to human health and have adverse eff ects for the environment. The household plays an important role in contributing to reuse and recovery, including recycling of waste equipment. For more information about the appropriate recycling methods, contact your local authority or retailer.

PROPERTIES OF THE TOOL

• The soldering tool has been designed for the purpose of soldering metals with tin and lead binders for soft soldering. A correct, reliable and safe functioning of the tool depends upon appropriate operation, and therefore:
• Before work with the tool, read the complete instruction and keep it.
• The supplier will not be held responsible for any damage and injuries which occur as a result of inappropriate applications of the tool, failure to observe safety regulations and the recommendations specifi ed in these instructions. Improper application of the tool will also cause cancellation of any guarantee rights due to incompliance with the sales contract.

EQUIPMENT

• The soldering tool is provided complete and has additional accessories: spare soldering tips, rosin and soldering tin.

TECHNICAL DATA

SAFE OPERATION INSTRUCTIONS

• It is prohibited to use soldering gun with a worn-out soldering tip.
• It is prohibited to touch insulation of electric conductors with a hot soldering tip.
• It is prohibited to use the soldering gun under high humidity conditions and in explosive and caustic gases and powders atmospheres.
• Do not repair damaged electric conductors of the tool. In case the electric cord of the device is damaged, it must be replaced with a new one. The power supply cord must be realised by a qualifi ed electrician.
• Do not solder live elements!
• This appliance is not to be used by children or persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance.

GENERAL SAFETY CONDITIONS

• NOTE! Get acquainted with all the instructions below. Failure to observe them may lead to an electric shock, fi re or injuries. The notion of electric tool used in the instructions applies to all the tools which are powered with electric current, both wire tools and wireless ones.

OBSERVE THE FOLLOWING INSTRUCTIONS

Place of work

• The place of work must be properly illuminated and clean. Disorder and poor illumination may be a cause of accidents. Do not work with electric tools in explosive environments, or those which contain infl ammable liquids, gases or vapours. Electric tools generate sparks, which may cause a fi re in case of contact with infl ammable gases or vapours.
• Do not allow children and outsiders to the place of work. A lack of concentration may result in a loss of control over the tool.

Electric safety

• The plug of the power supply cable must fi t the mains socket. Do not modify the plug. Do not use any adapters whatso-ever in order to adapt the plug to the socket. Unmodifi ed plug which fi ts the socket reduces the risk of an electric shock. Avoid contact with grounded surfaces, such as pipes, heaters and refrigerators. Grounding of the body increases the risk of an electric shock.
• Do not expose electric tools to precipitation or humidity. Water and humidity which gets into the electric tool increases the risk of an electric shock.
• Do not overload the power supply cable. Do not use the power supply cable in order to carry the tool or to connect and disconnect the plug from the mains socket. Avoid contact of the power supply cable with heat, oils, sharp tools and moving elements.
• Damage to the power supply cable increases the risk of an electric shock.
• In case work is realised outside closed areas, it is necessary to use extension cords designed for applications outside closed areas. Using a correct extension cord permits to reduce the risk of an electric shock.

Personal safety

• Commence work in good physical and psychological conditions. Pay attention to what you do. Do not work if you are tired or under eff ects of medicines or alcohol. Even a moment’s inattention during work may lead to serious injuries. Always use individual means of protection. Always wear goggles. Using individual means of protection, such as dust-masks, protective shoes, helmets and hearing protections permits to reduce the risk of serious injuries.

• Avoid accidental activation of the tool. Make sure the switch is in the OFF position, before you connect the tool to the mains. Holding the tool with a fi nger on the switch or connecting an electric tool when the switch is in the ON position may lead to serious injuries.

• Before you turn an electric tool on remove all the spanners and other tools, which have been used for adjustments. A spanner left on rotating elements of the tool may lead to serious injuries.

• Keep your balance. Maintain an appropriate position. It will permit to control the electric tool in case of unpredicted situations during its operation. Use protective clothes. Do not wear loose clothes or jewellery. Keep your hair, clothes and gloves away from moving elements of the electric tool. Loose clothes, jewellery or long hair may get caught on moving elements of the tool.

• Use dust extractors or dust containers, if the tool is equipped with any. Make sure they are properly connected. Using of dust extractors permits to reduce the risk of serious injuries.

• Operation of the electric tool

• Do not overload the electric tool. Use a proper tool for the given purpose. A correct selection of the tool for the given work will result in a more effi cient and safer work.

• Do not use the electric tool if the switch is not functioning properly. A tool which may not be controlled by means of a switch is dangerous and must be repaired.

• Disconnect the plug from the mains socket before any adjustment, replacement of accessories or storage of the tool. It will permit to avoid accidental activation of the electric tool.

• Store the tool away from children. Do not allow untrained persons to operate the tool. An electric tool may be dangerous in hands of an untrained person.

• Make sure the tool is properly maintained. Check the tool in order to detects any unfi tting or loose moving elements. Check whether the elements of the tool are not damaged. In case any damaged elements of the tool are detected, they must be repaired before the electric tool is operated. Many accidents are caused by improper maintenance of tools. Cutting tools must be sharp and clean. Properly maintained cutting tools are easier to control during work.

• Use electric tools and accessories in accordance with the aforementioned instructions. Use the tool in accordance with its purpose, taking into account the kind and conditions of work. Should the tool be used for other applications than the ones it has been designed for, the risk of a dangerous situation increases.
  Repairs

• The tool may be repaired only by authorised service centres, which must use solely original spare parts. It will guarantee a proper level of safety of operation of the electric tool.

FITTING ACCESORIES

• NOTE! Fitting of accessories must be executed exclusively with the power supply off (Remove the plug of the cord of the tool from the socket!)
• The soldering tool is supplied complete and does not require assembly.

PREPARATION FOR WORK

• Before work check whether the body and the cord with a plug and the external extension cords are not damaged. If necessary clan the tool and the ventilating holes. If any damage is detected, it is prohibited to continue working!
• Note! All activities related to replacement of the soldering tip, light bulb, etc. must be performed with the power supply of the tool off , so before you proceed to execute them: Remove the plug of the cord of the tool from the socket!
• Before using the tool, make sure the parameters of the mains comply with those indicated in the rating plate.
• Before soldering clean thoroughly the metal elements to be soldered, as well as the soldering tip of the tool. In case the soldering tip is burned, it must be replaced with a new one.

USING THE TOOL

• Soldering should be performed by an adult who is acquainted with the safety regulations for soldering.
• Note! The tool has not been designed for continuous operation! The maximum time of operation is 12 seconds, after which work must be interrupted for at least 48 seconds.

MAINTENANCE AND INSPECTIONS

NOTE! Before any adjustment, technical service or maintenance, the plug of the tool must be removed from the mains socket. Once work has been concluded check the technical conditions of the electric tool by means of visual inspection and evaluation of the body and handle, the electric cord with the plug, operation of the switch, clearance of the ventilating holes, sparking of the brushes, the level of noise emitted by the bearings and gears, start and smoothness of operation. Within the guarantee period, the user must not dismantle the electric tool or replace any subassemblies or components, since it will make the guarantee void. Any irregularities observed during inspection or operation of the tool indicate it must be repaired by a service centre. Once work has concluded, the body, ventilating holes, switches, additional handle and protections must be cleaned, for example with an air jet (whose pressure must not exceed 0.3 MPa), brush or a dry cloth, without any chemicals or cleaning liquids. The tool and the handles must be cleaned with a dry, clean cloth.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>