TROY LIGHTING F5524 Origami LED Pendant Light Installation Guide

: June 10, 2024
: TROY LIGHTING

Table of Contents

F5524 Origami LED Pendant Light
FIXTURE PREPARATION
FIXTURE INSTALLATION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

F5524 ORIGAMI 1LT MEDIUM PENDANT SILVER INSTALLATION
INSTRUCTIONS MANUAL

F5524 Origami LED Pendant Light

WARNING
DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE
READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.

CAUTION

TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES.
INSTALLATION AND MAINTENANCE OF THIS UNIT REQUIRES AN ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.
If.an existing fixture is being replaced, remove it and note to which of the wires in the outlet box the fixture was attached. DO NOT SEPARATE ANY OTHER WIRES THAT MAY BE IN THE BOX. DO NOT DAMAGE THE INSULATION OF OLDER WIRING. In regular circumstances the BLACK wire will be the “Hot” lead and the WHITE wire will be the “Neutral” or “Common” lead. in older buildings it is always good practice to reconfirm the polarity of the wiring.

NOTICE

The important safeguards and instructions outlined on this sheet cannot cover all possible conditions and situations that may occur. it must be understood that common sense, caution and care factors that cannot be built into any product.
Caution and care must be supplied by the person(s) installing, operating and caring of this lighting fixture.
This fixture is designed to be mounted on a correctly installed standard round or octagon box or a through wiring box with a plaster frame. The box must be securely mounted to the structure of the building. The heavy duty strap and hardware supplied should be used. directly mounting the fixture to the outlet box may make it impossible to correctly align the fixture.
This fixture is supplied with with a 4-pcs. stem. There is one 6″ section, two 12″ section and one 18″ section.
This feature allows the fixture to be mounted with a stem up to 48” in length in 6” increments.
This fixture is supplied with a swivel. By rotating the canopy the fixture may be mounted to angled ceiling.

FIXTURE PREPARATION

Remove the fixture, glass parts and parts bag(s) from the carton.

NOTICE:

Before discarding the carton, double check to make certain that all parts are found.

FIXTURE INSTALLATION

Attach the heavy duty strap to the outlet box using the mounting screws.
NOTICE:
THIS LUMINAIRE MUST BE MOUNTED OR SUPPORTED INDEPENDENTLY OF AN OUTLET BOX.
Determine the overall desired length of the fixture. Tape the end of the leads to a stiff wire (coat hanger) to aid in pulling them through the stems. Place the canopy onto the stem. Assemble the top stem section, decorative breaker, fixture stem and swivel. Place the swivel block over the stem connector of the canopy and thread the hex nuts onto them.
Thread the studs into the heavy duty strap at the spacing that matches the mounting holes in the canopy. Adjust the screw so they extend 3/16″ beyond the canopy.
Cut off the excess fixture wire 6″ beyond the canopy. Strip 12” of insulation from the ends of the wire. Twist the wire stands together.
Fasten the white fixture lead of the LED Light to the white wire in the outlet box.
Fasten the wires together with an approved fastener (wire nut). Starting about 1″ below the fastener, tightly wrap the connection with electrical tape so that the connections seals the end of the fastener.
WARNING
Make sure that there is no exposed wire or strands that could cause a dangerous short circuit!
Connect the black fixture lead of the LED Light to the black wire in the outlet box. Fasten the joined wires as in step 5.
NOTE: This fixture is rated for G9 4W LED lamp.
Place the glass diffuser into place. (See Figure 2) GLASS DIFFUSER INSTALLATION A. Untighten the Fitter A from Fitter B allowing the Glass cover to make space for the Glass diffuser.
B. Place the Glass diffuser beyond the Glass holder.
NOTE : Please handle the glass diffuser with care when putting to the glass holder.
C. Tighten back the Fitter A to Fitter B just enough to hold the Glass diffuser.
WARNING
DO NOT EXCEED RECOMMENDED WATTAGE!
Restore power to circuit at breaker or fuse box.