B-TECH BT8228 Heavy Duty Twin Cantilever Arm Flat Screen Wall Mount Installation Guide
- June 10, 2024
- B-TECH
Table of Contents
B-TECH BT8228 Heavy Duty Twin Cantilever Arm Flat Screen Wall Mount
SPECIFICATIONS
- Recommended for screens from 65″ (165cm) up to 120″ (305cm
- Max load: 125kg (275lbs)
- Suitable for screens with VESA® and non-VESA fixings from 300 × 200mm up to 800 x 600mm
- Extends: 90mm (3.5″) – 628mm (24.75″) from wall
- Features three swivel points: at wall, central pivot & interface
- Includes tool-less tilt, screen levelling & lateral adjustmentonce mounted
- Integrated cable management
- All mounting hardware included
INSTALLATION SAFETY INSTRUCTIONS
CAUTION: This mount is intended for use only with the maximum weights indicated. Use with equipment heavier than the maximum indicated may result in instability causing possible injury.
- Do not attempt to install this product until all instructions and warnings have been read and properly understood.
- Please keep these instructions for future reference.
- Please check carefully to make sure there are no missing or defective parts – defective parts must never be used.
- B-Tech AV Mounts, its distributors and dealers are not liable or responsible for damage or injury caused by improper installation, improper use or failure to observe these safety instructions. In such cases, all guarantees will expire.
General
B-Tech AV Mounts recommends that a professional AV installer or other suitably
qualified person install this product. Great care must always be taken during
installation as most AV equipment is of a fragile nature, possibly heavy and
easily damaged if dropped. If you do not fully understand the instructions or
are not sure how to install this product safely, then please consult a
professional for advice and/or to install this product for you. Failure to
mount this product correctly may cause serious injury or death both during
installation and at any time thereafter. Do not mount any AV equipment that
exceeds the specific weight limit of the product you are installing. This
weight limit will be clearly stated on each product and its packaging and will
vary from product to product.
Fixing hardware
It is highly recommended that all fixing screws be used where supplied and
that the purpose of all other fixing hardware is fully understood. In some
cases more AV equipment fixing hardware will be supplied to accommodate
different models of equipment and set up configurations. The installer must be
satisfied that any supplied fixing hardware is suitable for each specific
installation. The fixing kit supplied with the product may not be suitable for
all walls. If any fixing screws or included hardware are deemed not sufficient
for a safe installation then please consult a professional or your local
hardware store.
Hazard limitation
When routing cables take advantage of any built in cable management features
that the product might provide and ensure that all cables are tidy and secure.
Check to see that any moving aspect of the product can do so unhindered by any
cabling. Some products have moving parts and the potential to cause injury
through the crushing or trapping of fingers or other body parts. Particular
attention to the nature of moving parts is required especially when assembling
installing and adjusting during set up. Immediately after installation double-
check that the work done is safe and secure. Double-check all necessary
fixings are present and are of ample tightness. It is recommended that
periodic inspections of the product and its fixing points are made as
frequently as possible (no more than 6 months apart) to ensure that safety is
maintained. If in doubt consult a professional AV installer or other suitably
qualified person.
- B-Tech AV Mounts recommends that this product be installed by a qualified AV technician or other suitably qualified person.
- B-Tech AV Mounts, its distributors and dealers are not liable or responsible for damage or injury caused by improper installation, improper use or failure to observe these safety instructions. In such cases, all guarantees will expire.
- This product must be mounted on a suitable surface and may only be used up to the specified maximum weight.
PARTS LIST
INSTALLATION TOOLS REQUIRED
INSTALLATION INSTRUCTIONS
FIX MOUNT TO WALL
-
Decide which wall fixing holes to use (we recommend using 6).
-
Determine the centre of the screen on the wall. Mark the centre.
-
Use the drilling template* (item 5) to drill fixing holes on the wall.
Note: Ensure centre-lines on drilling template align with desired centrepoint on wall. -
Insert item A3 into drilled holes.
Note : item A3 not required for installations onto wooden walls. -
KEYHOLE MOUNTING – Insert item A1 in the top centre hole (leave a 5mm gap to hook on item 1).
-
Hook item 1 onto item Al.
-
Fix item 1 to the wall using items A1 & A2.
Ensure the mount is level and then fully tighten all fixings screws
ATTACH COVERS TO WALL PLATE
ANTENCHO WE ENC ACE ARMANS TO SCREEN the interface kit (items A-N)
Fix item 2 to the back of the screen using the interface kit (items A-M
Note: Ensure the arms are positioned the correct way round and the same
holes are used on both arms.
INTERFACE KIT
Note: Spacers (items J, K, L & M) are to be used for screens with recessed fixings.
HOOK SCREEN ONTO MOUNT
- Using item 2 hook the screen onto the top and bottom mounting rails on item 1.
LATERAL ADJUSTMENT
Slide item 2 along item 1 to position screen in desired position.
SECURE INTERFACE ARMS TO MOUNT
Tighten the safety screws on the bottom of both items 2 into item 1 using item
4.
CABLE MANAGEMENT
-
Fully extend screen from wall. Slide out top or bottom cable management cover by sliding away from wall and then out of channel as shown.
-
Route cables from screen, through articulating arm and out to the wall.
Note: Ensure length of cable allows screen to be moved freely. -
Click cover back in to secure cables
CHECK MOBILITY
Check screen mobility to ensure no cables are pulled out of position.
SCREEN ADJUSTMENT
Screen levelling – Loosen handwheel, adjust screen level and retighten hand
wheel.
SCREEN TILT
Adjust screen tilt by hand: +15 degrees / -3 degrees
DIMENSIONS
FRONT VIEW
BACK VIEW
TOP VIEW
SIDE VIEW
TILT RANGE
SCREEN LEVELLING
QR SCAN
©2022 B-Tech International Design and Manufacturing Ltd. All rights reserved. B-Tech AV Mounts is a division of B-Tech International Design and Manufacturing Ltd.B-Tech AV Mounts and the B-Tech logo are registered trade marks. All other brands and product names are trademarks of their respective owners. Photographs are for illustrative purposes only. E&OE.
CONTACT:
info@btechavmounts.com
© For More Information Visit www.btechavmounts.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>