antaira LNP-1002G-SFP-24 Series 10 Port Industrial Gigabit PoE Plus Unmanaged Ethernet Switch Installation Guide
- June 10, 2024
- antaira
Table of Contents
antaira LNP-1002G-SFP-24 Series 10 Port Industrial Gigabit PoE Plus
Unmanaged Ethernet Switch
Product Information
The Antaira Technologies LNP-1002G-SFP-24 Series is a 10-port industrial gigabit PoE+ unmanaged Ethernet switch with 810/100/1000Tx ports (30W/port) and 2 100/1000 SFP slots. It has a store-and-forward switching architecture, an 8K MAC address table, and supports jumbo frames up to 9.6K. The switch has dual DC power inputs with a 6-pin removal terminal block that supports 12~55VDC power input. It has IP30 protection and can be mounted on a DIN-rail or wall.
Product Usage Instructions
Package Check List
Before using the LNP-1002G-SFP-24 Series, please check if the
package includes the following items:
- LNP-1002G-SFP-24 Series switch
- Quick installation guide (Version 1.1, March 2022)
Front Panel Layout
The front panel layout of the LNP-1002G-SFP-24 Series includes:
- Grounding screw
- LED for Power 1, Power 2, and Fault
- LAN#1~8 LED for link/activity status (1000Mbps)
- LAN#1~8 LED for link/activity status (10/100Mbps)
Top Panel View
The top panel of the LNP-1002G-SFP-24 Series is equipped with a 6-pin
removal terminal block connector for dual DC power inputs (12~55VDC) and a
grounding screw.
LED Indicators
The LNP-1002G-SFP-24 Series has LED indicators for Power 1, Power 2, Fault, PoE indicators (Port 1~8), LAN Port 1~8 (Upper LED), and LINK/ACT (SFP Port 9~10). The LED colors and their status are as follows:
| LED | Color | Status |
|---|---|---|
| Power 1 | Green | On |
| Power 2 | Green | On |
| Fault | Green | Flashing |
| PoE Indicators (Port 1~8) | Red | |
| Green | On (Port is supplying power) |
Flashing (Port is detecting a PD device)
LAN Port 1~8 (Upper LED)| Green| On (Link is up)
LAN Port 1~8 (Lower LED)| Green| Flashing (Activity is detected)
LINK/ACT (SFP Port 9~10)| Green
Amber| On (Link is up)
Flashing (Activity is detected)
Ethernet Ports
All RJ45 ports of the LNP-1002G-SFP-24 Series support the auto MDI/MDI-X
function and are auto-sensing for 10Base-T, 100Base-TX, or 1000Base-T device
connections. Please follow the wiring pin
assignment table below for Ethernet port installation:
| Pins | T568A Color | T568B Color |
|---|---|---|
| Pin 1 | white/green stripe | white/orange stripe |
| Pin 2 | green solid | orange solid |
| Pin 3 | white/orange stripe | white/green stripe |
| Pin 4 | blue solid | white/blue stripe |
| Pin 5 | white/blue stripe | blue solid |
| Pin 6 | orange solid | green solid |
| Pin 7 | white/brown stripe | white/brown stripe |
| Pin 8 | brown solid | brown solid |
Power Input Wiring
Please follow the steps below to insert the power wire:
- Insert the positive and negative wires into the PWR1 (V1+, V1-) and PWR2 (V2+, V2-) contacts on the terminal block connector as shown in Figure 1.
- Tighten the wire-clamp screws to prevent the wires from loosening, as shown in Figure 2. (Please refer to the user manual for Figures 1 and 2)
Industrial Switch Mounting
The LNP-1002G-SFP-24 Series can be mounted on a DIN-rail or wall. Please
follow the steps below for mounting:
DIN-Rail Mounting
The DIN-Rail bracket is pre-installed on the industrial Ethernet switch from
the factory. Follow the steps below for installing the industrial switch on
the DIN-Rail track:
- Insert the top of the DIN-Rail onto the track.
- Lightly pull down the bracket onto the rail.
- Check if the bracket is mounted tightly on the rail.
- To remove the industrial Ethernet switch from the rail, do the opposite from the steps above. (Please refer to the user manual for Figures 3, 4, and 5)
Wall Mounting
Follow the steps below to mount the industrial Ethernet switch using the wall
mounting bracket:
- Attach the wall mounting bracket to the back of the switch.
- Use screws to mount the switch on the wall. (Please refer to the user manual for Figure 6)
Package Check List
The package contains the following items:
- 1 – Quick installation guide
- 1 – LNP-1002G-SFP-24(-T)
- 1 – Wall mounting bracket set with screws
- 1 – DC cable –18 AWG & DC jack 5.5 x 2.1mm
- 1 – Dust cover set
Front Panel Layout
Top Panel View
LNP-1002G-SFP-24 series top panel is equipped with one 6-pin removal terminal
block connector for dual DC power inputs (12~55VDC).
Product Overview
System Interface/Performance
- All RJ45 ports support the auto MDI/MDI-X function
- Embedded 810/100/1000Tx (30W/Port) and 2100/1000 SFP slots
- Store-and-Forward switching architecture
- 8K MAC address table
- Jumbo frame supports 9.6K
Power Input & Connection
- DC 12 to 55V redundant power, with a 6-pin removal terminal block
- It is recommended to use a UL listed industrial power supply Operating Temperature
- Standard operating temperature model: -10°C to 70°C Extended operating temperature model: -40°C to 75°C
Case/Installation
- IP30 protection
- DIN-Rail and wall mount design
LED Indicators
| LED | Color | Description |
|---|---|---|
| Power 1 | Green | On |
| Off | Power input 1 is inactive | |
| Power 2 | Green | On |
| Off | Power input 2 is inactive | |
| Fault | Red | On |
| Off | Both power input 1 and 2 are active | |
| PoE Indicators (Port 1~8) | Green | On |
powered-device
Off| No powered-device attached or power supplying fails
LAN Port 1~8 (Upper LED)| ****
Green
| On| Connected to network, 1000Mbps
Flashing| Networking is active
Off| Not connected to network
LAN Port 1~8 (Lower LED)| ****
Green
| On| Connected to network, 10/100Mbps
Flashing| Networking is active
Off| Not connected to network
LINK/ACT
(SFP Port 9~10)
| Green| On| Connected to network, 1000Mbps
Flashing| Networking is active
Off| Not connected to network
Amber| On| Connected to network, 100Mbps
Flashing| Networking is active
Off| Not connected to network
Quick Installation
Ethernet Ports
RJ45 Ports (Auto MDI/MDIX)
All RJ45 ports are auto-sensing for 10Base-T, 100Base-TX or 1000Base-T device
connections. Please follow the wiring pin assignment table below for Ethernet
port installation.
RJ45 Ethernet Port Pin Outs
RJ45 Ethernet Port Pin Outs
Pins
| ****
T568A Color
| ****
T568B Color
| 10Base-T, 100Base-TX| 1000
Base- T(X)
Pin 1| white/green stripe| white/orange stripe| Rx+| TP0+
Pin 2| green solid| orange solid| Rx-| TP0-
Pin 3| white/orange stripe| white/green stripe| Tx+| TP1+
Pin 4| blue solid| blue solid| unused| TP2+
Pin 5| white/blue stripe| white/blue stripe| unused| TP2-
Pin 6| orange solid| green solid| Tx-| TP1-
Pin 7| white/brown stripe| white/brown stripe| unused| TP3+
Pin 8| brown solid| brown solid| unused| TP3-
Power Input Wiring
Please follow the steps below to insert the power wire:
- Insert the positive and negative wires into the PWR1 (V1+, V1-) and PWR2 (V2+, V2-) contacts on the terminal block connector as shown below in Figure 1.
- Tighten the wire-clamp screws to prevent the wires from loosening, as shown below in Figure 2.
Industrial Switch Mounting
DIN-Rail Mounting
The DIN-Rail bracket is pre-installed on the industrial Ethernet switch from
the factory. Please refer to Figure 3 for a DIN-Rail bracket installation
reference. Follow the steps below for installing the industrial switch on the
DIN-Rail track:
-
Insert the top of the DIN-Rail on to the track as shown below in Figure 4.
-
Lightly pull down the bracket on to the rail as shown below in Figure 5.
-
Check if the bracket is mounted tightly on the rail.
-
To remove the industrial Ethernet switch from the rail, do the opposite from the steps above.
Wall Mounting
Follow the steps below to mount the industrial Ethernet switch using the wall
mounting bracket as shown below in Figure 6.
- Remove the DIN-Rail bracket from the industrial Ethernet switch by loosening the screws.
- Place the wall mounting brackets on the top and bottom of the industrial Ethernet switch.
- Use the screws to screw the wall mounting bracket on the industrial Ethernet switch.
- Use the hook holes at the corners of the wall mounting bracket to hang the industrial Ethernet switch on the wall.
- To remove the wall mount bracket, do the opposite from the steps above.
Field Maintenance and Service
- If the device requires servicing of any kind, the user is required to disconnect and remove it from its mounting. The initial installation should be done in a way that makes this as convenient as possible.
- Voltage/power lines should be properly insulated as well as other cables. Be careful when handling them so as to not trip over.
- Do not under any circumstance insert foreign objects of any kind into the heat dissipation holes located in the different faces of the device. This may not only harm the internal layout, but might cause harm to user as well.
- Do not under any circumstance open the device for any reason. Please contact your dealer for any repair needed or follow the instructions within the manual.
Warranty Policy
Warranty Conditions Products supplied by Antaira Technologies are covered in this warranty for sub-standard performance or defective workmanship. The warranty is not, however, extended to goods damaged in the following circumstances:
- Excessive forces or impacts
- War or an Act of God: wind storm, fire, flood, electric shock, earthquake
- Use of unqualified power supply, connectors, or unauthorized parts/kits
- Replacement with unauthorized parts
RMA and Shipping Costs Reimbursement
Customers shall always obtain an authorized “RMA” number from Antaira before
shipping the goods for repair or replacement.
- Within the warranty period (based on the invoice date), all parts and labor are free of charge to the customers.
- Customers are responsible for the cost of parts and labor, if the products are out of warranty.
- For RMA service, customers are responsible for the shipping expense for shipping the RMA unit(s) to Antaira. Antaira is responsible for the shipping expense via a ground service for the return repair/replace unit(s) back to customers.
Limited Liability
Antaira would not be held responsible for any consequential losses from
using Antaira’s product.
Warranty Period
5-Year Warranty
Antaira’s Customer Service and Support
Antaira’s Technical Service & Support Centers:
+ 844-268-2472 ( Antaira US
Headquarter )
+ 48-22-862-88-81 ( Antaira Europe Office )
+ 886-2-2218-9733 ( Antaira Asia Office )
Antaira’s Web Sites & Repair/Support Emails:
www.antaira.com /
support@antaira.com
www.antaira.eu /
info@antaira.eu
www.antaira.com.tw /
info@antaira.com.tw
*Any changes will be announced on the Antaira website.
Documents / Resources
|
antaira LNP-1002G-SFP-24 Series 10 Port Industrial Gigabit PoE Plus Unmanaged
Ethernet
Switch
[pdf] Installation Guide
LNP-1002G-SFP-24, LNP-1002G-SFP-24 Series 10 Port Industrial Gigabit PoE Plus
Unmanaged Ethernet Switch, LNP-1002G-SFP-24 Series, 10 Port Industrial Gigabit
PoE Plus Unmanaged Ethernet Switch, Industrial Gigabit PoE Plus Unmanaged
Ethernet Switch, Gigabit PoE Plus Unmanaged Ethernet Switch, Unmanaged
Ethernet Switch, Ethernet Switch, Switch
---|---
References
- Antaira Technologies | Industrial Networking Solutions
- Antaira Technologies Asia | Industrial Networking Product Solutions
- Antaira Technologies PoE Switches, converters and modules, Bluetooth adapters, servers - Antaira Technologies
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>