antaira LNP-C501G-SFP-bt-24 Series 5 Port Ethernet Switch Installation Guide
- October 27, 2023
- antaira
Table of Contents
LNP-C501G-SFP-bt-24 Series 5 Port Ethernet Switch
Installation Guide
LNP-C501G-SFP-bt-24 Series
5-Port Industrial Compact Gigabit IEEE 802.3bt PoE++
Unmanaged Ethernet Switch, 410/100/1000TX (90W/Port),
1100/1000 SFP Slot; 9~55VDC Power Input
Package Checklist
The package contains the following items:
- 1 – Quick installation guide
- 1 – LNP-C501G-SFP-bt-24(-T)
- 1 – Wall mounting bracket set with screws
- 1 – DC cable –18 AWG & DC jack 5.5 x 2.1mm
- 1 – Dust cover set
Front Panel Layout
Product Overview
System Interface/Performance
- All RJ45 ports support the auto MDI/MDI-X function
- Embedded 410/100/1000Tx (90W/Port) RJ45 ports and 1100/1000 SFP slots
- Store-and-Forward switching architecture
- 8K MAC address table
- Supports 10Kbytes jumbo frame
- 1Mbits memory buffer
Power Input & Connection
- DC 9 to 55V redundant power, with a 6-pin removal terminal block
- It is recommended to use a UL listed industrial power supply
- For bt PoE application(s), the recommended power input should be not less than 53VDC
Operating Temperature
- Standard operating temperature model: -10°C to 65°C
- Extended operating temperature model: -40°C to 75°C Case/Installation
- IP40 protection
- DIN-Rail and wall mount design
LED Indicators
LED | Color | Description |
---|---|---|
Power 1 | Green | On |
Off | Power input 1 is inactive | |
Power 2 | Green | On |
Off | Power input 2 is inactive | |
Fault | Red | Off |
On | Any of the listed trigger events occur |
1. Power 1 or Power 2 is inactive
2. Total PoE loading is > 100% PoE Budget
3. PoE over current (per port)
4. Cable short (per port)
5. One of the channels in Dual PD fail
PoE Load| –| Off| PoE Load s50%
Blue| On| PoE Load 51-70%
Blue & Red| On| PoE Load 71-90%
Blue & Red
(Red flashing)| On| PoE Load 91-100%
SFP Port| Green| On| Connected to network, 100 or 1000Mbps
Flashing| Networking is active
Off| Not connected to network
LAN Port 2-5
LN K/ACT
(Upper LED)| | On| Connected to network, 10/100/1000Mbps
Flashing| Networking is active, 10/100/1000Mbps
Off| Not connected to network
LAN Port 2-5
PoE Mode
(Lower LED)| | On| IEEE 802.3bt connection
(Single Signature PD Class 5-8/Dual Signature PD Channel Class 1-5)
Off| No powered-device attached or power supplying fails
| On| IEEE 802.3af/at connection (Single Signature PD Class 0-4)
Off| No powered-device attached or power supplying fails
DIP Switch
The 4-pin DIP switch on the front panel of the Ethernet switch works as the
PoE controller for PoE port 2~5.
DIP Switch Number | ON (Default) | OFF |
---|---|---|
PoE DIP Switch 1 | Enable Port 2 PoE Function | Disable Port 2 PoE Function |
PoE DIP Switch 2 | Enable Port 3 PoE Function | Disable Port 3 PoE Function |
PoE DIP Switch 3 | Enable Pod 4 PoE Function | Disable Port 4 PoE Function |
PoE DIP Switch 4 | Enable Pod 5 PoE Function | Disable Port 5 PoE Function |
The 2-pin DIP switch is used to enable/disable PD Remote Reset Technology (PRRT) and control SFP speed.
DIP Switch Number | ON | OFF (Default) |
---|---|---|
DIP Switch 1 | Enable PRRT Function | Disable PRRT Function |
DIP Switch 2 | Control SFP speed at 100Mbps | Control SFP speed at 1Gbps |
NOTE: The device will reboot when the Dip switch of PRRT and SFP setting is changed.
Quick Installation
Ethernet Ports
RJ45 Ports (Auto MDI/MDI-X)
All RJ45 ports are auto-sensing for 10Base-T, 100Base-TX or 1000Base-T device
connections. Please follow the wiring pin assignment table below for Ethernet
port installation.
RJ45 Ethernet Port Pin Outs| | |
---|---|---|---
Pins| T568A Color| T568B Color| 10Base-T,
100Base-TX| 1000
Base-T(X)
Pin 1| white/green stripe| white/orange stripe| Rx+| TPO+
Pin 2| green solid| orange solid| Rx-| TP0-
Pin 3| white/orange stripe| white/green stripe| Tx+| TP1+
Pin 4| blue solid| blue solid| unused| TP2+
Pin 5| white/blue stripe| white/blue stripe| unused| TP2-
Pin 6| orange solid| green solid| Tx-| TP1-
Pin 7| white/brown stripe| white/brown stripe| unused| TP3+
Pin 8| brown solid| brown solid| unused| TP3-
Power Input Wiring
Please follow the steps below to insert the power wire:
- Insert the positive and negative wires into the PWR1 (V1+, V1-) and PWR2 (V2+, V2-) contacts on the terminal block connector as shown below in Figure 1.
- Tighten the wire-clamp screws to prevent the wires from loosening, as shown below in Figure 2.
Industrial Switch Mounting
DIN-Rail Mounting
The DIN-Rail bracket is pre-installed on the industrial Ethernet switch from
the factory. Please refer to Figure 3 for a DIN-Rail bracket installation
reference.
Follow the steps below for installing the industrial switch on the DIN-Rail
track:
-
Insert the top of the DIN-Rail onto the track as shown below in Figure 4.
-
Lightly pull down the bracket onto the rail as shown below in Figure 5.
-
Check if the bracket is mounted tightly on the rail.
-
To remove the industrial Ethernet switch from the rail, do the opposite from the steps above.
Wall Mounting
Follow the steps below to mount the industrial Ethernet switch using the wall
mounting bracket as shown below in Figure 6.
- Remove the DIN-Rail bracket from the industrial Ethernet switch by loosening the screws.
- Place the wall mounting brackets on the top and bottom of the industrial Ethernet switch.
- Use the screws to screw the wall mounting bracket on the industrial Ethernet switch.
- Use the hook holes at the corners of the wall mounting bracket to hang the industrial Ethernet switch on the wall.
- To remove the wall mount bracket, do the opposite from the steps above.
Field Maintenance and Service
- If the device requires servicing of any kind, the user is required to disconnect and remove it from its mounting. The initial installation should be done in a way that makes this as convenient as possible.
- Voltage/power lines should be properly insulated as well as other cables. Be careful when handling them to not trip over them.
- Do not under any circumstance insert foreign objects of any kind into the heat dissipation holes located in the different faces of the device. This may not only harm the internal layout but might cause harm to the user as well.
- Do not under any circumstance open the device for any reason. Please contact your dealer for any repair needed or follow the instructions within the manual.
Warranty Policy
Warranty Conditions
Products supplied by Antaira Technologies are covered in this warranty for
sub-standard performance or defective workmanship. The warranty is not,
however, extended to goods damaged in the following circumstances:
(a) Excessive forces or impacts
(b) War or an Act of God: wind storm, fire, flood, electric shock, earthquake
(c) Use of unqualified power supply, connectors, or unauthorized parts/kits
(d) Replacement with unauthorized parts
RMA and Shipping Costs Reimbursement
Customers shall always obtain an authorized “RMA” number from Antaira before
shipping the goods for repair or replacement.
- Within the warranty period (based on the invoice date), all parts and labor are free of charge to the customers.
- Customers are responsible for the cost of parts and labor if the products are out of warranty.
- For RMA service, customers are responsible for the shipping expense for shipping the RMA unit(s) to Antaira.
Antaira is responsible for the shipping expense via a ground service for the return repair/replacement unit(s) to customers.
Limited Liability
Antaira would not be held responsible for any consequential losses from using
Antaira’s product.
Warranty Period
5-Year Warranty
Antaira’s Customer Service and Support
-
Antaira’s Technical Service & Support Centers:
+ 844-268-2472 (Antaira US Headquarter)
+ 48-22-862-88-81 (Antaira Europe Office)
+ 886-2-2218-9733 (Antaira Asia Office) -
Antaira’s Web Sites & Repair/Support Emails:
www.antaira.com / support@antaira.com
www.antaira.eu / info@antaira.eu
www.antaira.com.tw / info@antaira.com.tw
*Any changes will be announced on the Antaira website.
References
- Antaira Technologies | Industrial Networking Solutions
- Antaira Technologies Asia | Industrial Networking Product Solutions
- Antaira Technologies PoE Switches, converters and modules, Bluetooth adapters, servers - Antaira Technologies
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>