antaira LMP-2602G-SFP 26-Port Industrial PoE Plus Gigabit Managed Ethernet Switch Installation Guide

: October 30, 2023
: antaira

Table of Contents

LMP-2602G-SFP 26-Port Industrial PoE Plus Gigabit Managed Ethernet Switch
Package Check List
Front Panel Layout
Product Overview
LED Indicators
Quick Installation
Industrial Switch Mounting
Field Maintenance and Service
Warranty Policy
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Antaira Technologies

antaira LMP-2602G-SFP 26-Port Industrial PoE Plus Gigabit Managed Ethernet
Switch Tel: 1-844-268-2472
Fax: 1-714-671-9944
www.antaira.com

LMP-2602G-SFP 26-Port Industrial PoE Plus Gigabit Managed Ethernet Switch

LMP-2602G-SFP Series
26-Port Industrial PoE+ Gigabit Managed Ethernet Switch, with 2410/100/1000Tx (30W/Port) and 2 Gigabit Combo Ports (210/100/1000Tx RJ45 and 2100/1000 SFP Slots)
Quick Installation Guide
Version 1.0
(September 2022)

Package Check List

The package contains the following items:

1 – Quick Installation Guide
1 – LMP-2602G-SFP(-T)
1 – Rack Mounting Brackets and Screws
1 – RJ45 to DB9 Serial Console Cable
1 – Dust Cover Set

Front Panel Layout

antaira LMP-2602G-SFP 26-Port Industrial PoE Plus Gigabit Managed Ethernet
Switch - Front Panel Layout Back Panel View
LMP-2602G-SFP series back panel is equipped with one 8-pin redundant power inputs (48~55VDC) and one 2-pin removal terminal block for relay output.

Product Overview

System Interface/Performance

All RJ45 ports support the auto MDI/MDI-X function
Embedded 2410/100/1000Tx RJ45 ports (30W/Port) and 2Gigabit combo ports (210/100/1000Tx and 2100/1000 SFP slots)
Store-and-forward switching architecture
8K MAC address table

Power Input & Connection

DC 48 to 55V through 8-pin redundant power inputs
It is recommended to use a UL listed industrial power supply

Operating Temperature

Standard operating temperature model: -10°C to 65°C
Extended operating temperature model: -40°C to 75°C

Case/Installation

IP40 Protection
1U Rackmount Design

LED Indicators

LED	Color	Description
Power 1	Green	On
Off	Power input 1 is inactive
Power 2	Green	On
Off	Power input 2 is inactive
Fault	Green	On
Red	On	1.System booting

Quick Installation

Ethernet RJ45 Port (Auto MDI/MDIX)
RJ45 port is auto-sensing for 10Base-T, 100Base-TX or 1000Base-TX device connections. Please follow the wiring pin assignment table below for the Ethernet port installation.
RJ45 Ethernet Port Pin Outs

Pins| T568A Color| T568B Color| 10/100
Base-T(X)| 1000
Base-T
---|---|---|---|---
1| White/Green| White/Orang| Rx+| TPO+
2| Green| Orange| Rx-| TP0-
3| White/Orang| White/Green| Tx+| TP1+
4| Blue| Blue| unused| TP2+
5| White/Blue| White/Blue| unused| TP2-
6| Orange| Green| Tx-| TP1-
7| White/Brown| White/Brown| unused| TP3+
8| Brown| Brown| unused| TP3-

SFP Slots
The Small Form-Factor Pluggable (SFP) is a compact optical transceiver used in optical communications.
Please follow the steps below for connecting the SFP and LC cable:

Insert the SFP transceiver module into the SFP slot as shown below in Figure 1 (Please be noted that the triangle mark is at the bottom of the SFP slot). Figure 2 shows the SFP transceiver module was inserted.
Insert the fiber cable of the LC connector into the transceiver as shown below in Figure 3.

Power Inputs Wiring
Please follow the below steps to insert the power wire:

Insert the positive and negative wires into the PWR1 (V1+, V1-) and PWR2 (V2+, V2-) contacts on the terminal block connector. See Figure 4.
Tighten the wire-clamp screws to prevent the wires from loosening.

Industrial Switch Mounting

The switch comes with a rack-mounted kit can be mounted in an EIA standard size, 19-inch rack. It can be placed in a wiring closet with other equipment.
Perform the following steps to rack-mount the switch.

Position one plate to align with the holes on one side of the hub and secure it with the smaller plate screws. Then, attach the remaining plate to the other side of the switch.
After attaching both mounting plates, position the switch in the rack by lining up the holes in the plates with the appropriate holes on the rack. Secure the switch to the rack with a screwdriver and the rack-mounting screws.

*Note: For proper ventilation, allow at least 4 inches (10 cm) of clearance on the front and 3.4 inches (8 cm) on the back of the switch. This is especially important for enclosed rack installation.

Field Maintenance and Service

If the device requires servicing of any kind, the user is required to disconnect and remove it from its mounting. The initial installation should be done in a way that makes this as convenient as possible.
Voltage/Power lines should be properly insulated as well as other cables. Be careful when handling them so as to not trip over it.
Do not under any circumstance insert foreign objects of any kind into the heat dissipation holes located in the different faces of the device. This may not only harm the internal layout, but might cause harm to user as well.
Do not under any circumstance open the device for any reason. Please contact your dealer for any repair needed or follow the instructions within the manual.

Warranty Policy

Warranty Conditions
Products supplied by Antaira Technologies are covered in this warranty for sub-standard performance or defective workmanship. The warranty is not, however, extended to goods damaged in the following circumstances:
(a) Excessive forces or impacts
(b) War or an Act of God: wind storm, fire, flood, electric shock, earthquake
(c) Use of unqualified power supply, connectors, or unauthorized parts/kits
(d) Replacement with unauthorized parts
RMA and Shipping Costs Reimbursement
Customers shall always obtain an authorized “RMA” number from Antaira before shipping the goods for repair or replacement.

Within the warranty period (based on the invoice date), all parts and labor are free of charge to the customers.
Customers are responsible for the cost of parts and labor, if the products are out of warranty.
For RMA service, customers are responsible for the shipping expense for shipping the RMA unit(s) to Antaira. Antaira is responsible for the shipping expense via a ground service for the return repair/replace unit(s) back to customers.

Limited Liability
Antaira would not be held responsible for any consequential
losses from using Antaira’s product.
Warranty Period
5-Year Warranty

Antaira’s Customer Service and Support
Antaira’s Technical Service & Support Centers:
+ 844-268-2472 (Antaira US Headquarter)
+ 4 8 – 2 2 – 8 6 2 – 8 8 – 8 1 (Antaira Europe Office)
+ 886-2-2218-9733 (Antaira Asia Office)
Antaira’s Web Sites & Repair/Support Emails:
www.antaira.com / support@antaira.com
www.antaira.eu / info@antaira.eu
www.antaira.com.tw / info@antaira.com.tw
*Any changes will be announced on the Antaira website.