antaira LNP-2004G-SFP Series 20- Port Industrial PoE pLUS Unmanaged Gigabit Ethernet Switch Installation Guide

: June 4, 2024
: antaira

Table of Contents

Package Check List
Front Panel Layout
Product Overview
LED Indicators
Quick Installation
Industrial Switch Mounting
Warranty Policy
Documents / Resources

Antaira Technologies
LNP-2004G-SFP Series
20- Port Industrial PoE+ Unmanaged Gigabit Ethernet Switch,
w/1610/100/1000Tx (30W/Port) + 4100/1000 SFP Slots
Quick Installation Guide
Version 1.1
(July 2020)

Package Check List

The package contains the following items:

1 – Quick installation guide
1 – LNP-2004G-SFP(-T)
1 – Wall mounting bracket set with screws
1 – DC cable –18 AWG & DC jack 5.5 x 2.1mm
1 – RJ45 dust cover set

Front Panel Layout

antaira LNP 2004G SFP Series 20- Port Industrial PoE pLUS Unmanaged Gigabit
Ethernet Switch

Top Panel View
LNP-2004G-SFP series’ top panel is equipped with one 6-pin removal terminal block connector for dual DC power inputs (48~55VDC). antaira LNP 2004G SFP
Series 20- Port Industrial PoE pLUS Unmanaged Gigabit Ethernet Switch -
Fig

Product Overview

System Interface/Performance

All RJ45 ports support the auto MDI function
Embedded 1610/100/1000Tx (PSE: 30W/Port) and 4100/1000 SFP slots
Store-and-Forward switching architecture
8K MAC Address Table
Supports 9,216bytes Jumbo Frame
512Kbytes memory buffer

Power Input & Connection

DC 48 to 55V redundant power, with a 6-pin removal terminal block
It is recommended to use a UL-listed industrial power supply
Operating Temperature
Standard operating temperature model: -10°C to 65°C
Extended operating temperature model: -40°C to 75°C
Case/Installation
IP30 protection
DIN-Rail and wall mount design

LED Indicators

LED	Color	Description
Power 1	Green	On
Off	Power input 1 is inactive
Power 2	Green	On
Off	Power input 2 is inactive
Fault	Red	On
Off	Both power inputs 1 and 2 are active
PoE Indicator (Port 1-16)	Green	On

Quick Installation

Ethernet Ports
RJ45 Ports (Auto MDI)
All RJ45 ports are auto-sensing for 10Base-T, 100Base-TX, or 1000Base-T device connections. Please follow the wiring pin assignment table for Ethernet port installation.

RJ45 Ethernet Port Pin Outs

antaira LNP 2004G SFP Series 20- Port Industrial PoE pLUS Unmanaged Gigabit
Ethernet Switch - Fig 3

Power Input Wiring
Please follow the steps below to insert the power wire:

Insert the positive and negative wires into the PWR1 (V1+, V1-) and PWR2 (V2+, V2-) contacts on the terminal block connector as shown below in Figure 1.
Tighten the wire-clamp screws to prevent the wires from loosening, as shown below in Figure 2.

Industrial Switch Mounting

DIN-Rail Mounting
The DIN-Rail bracket is pre-installed on the industrial Ethernet switch from the factory. Please refer to Figure 3 for a DIN-Rail bracket installation reference.
Follow the steps below for installing the industrial switch on the DINRail track:

Insert the top of the DIN-Rail on to the track as shown in Figure 4.
Lightly pull down the bracket onto the rail as shown in Figure 5.
Check if the bracket is mounted tightly on the rail. Figure 3
To remove the industrial Ethernet switch from the rail, do the opposite from the steps above.

Wall Mounting

Follow the steps below to mount the industrial Ethernet switch using the wall mounting bracket as shown below in Figure 6.

Remove the DIN-Rail bracket from the industrial Ethernet switch by loosening the screws.
Place the wall mounting brackets on the top and bottom of the industrial Ethernet switch.
Use the screws to screw the wall mounting bracket onto the industrial Ethernet switch.
Use the hook holes at the corners of the wall mounting bracket to hang the industrial Ethernet switch on the wall.
To remove the wall mount bracket, do the opposite from the steps above.

Field Maintenance and Service

If the device requires servicing of any kind, the user is required to disconnect and remove it from its mounting. The initial installation should be done in a way that makes this as convenient as possible.
Voltage/power lines should be properly insulated as well as other cables. Be careful when handling them so as to not trip over them.
Do not under any circumstance insert foreign objects of any kind into the heat dissipation holes located in the different faces of the device. This may not only harm the internal layout but might cause harm to the user as well.
Do not under any circumstance open the device for any reason. Please contact your dealer for any repair needed or follow the instructions within the manual.

Warranty Policy

Warranty Conditions
Products supplied by Antaira Technologies are covered in warranty for sub- standard performance or defective workmanship. The warranty is not, however, extended to
goods damaged in the following circumstances:
(a) Excessive forces or impacts
(b) War or an Act of God: wind storm, fire, flood, electric shock, earthquake
(c) Use of unqualified power supply, connectors, or unauthorized parts/kits
(d) Replacement with unauthorized parts
RMA and Shipping Costs Reimbursement
Customers shall always obtain an authorized “RMA” number from Antaira before shipping the goods for repair or replacement.

Within the warranty period (based on the invoice date), all parts and labor are free of charge to the customers.
Customers are responsible for the cost of parts and labor if the products are out of warranty.
For RMA service, customers are responsible for the shipping expense for shipping the RMA unit(s) to Antaira.
Antaira is responsible for the shipping expense via ground service for the return repair/replacement unit(s) back to customers.

Limited Liability
Antaira would not be held responsible for any consequential losses from using Antaira’s product.
Warranty Period
5-Year Warranty
Antaira’s Customer Service and Support

Antaira’s Technical Service & Support Centers:
+ 844-268-2472 (Antaira US Headquarters)
+ 48-22-862-88-81 (Antaira Europe Office)
+ 886-2-2218-9733 (Antaira Asia Office)
Antaira’s Web Sites & Repair/Support Emails:
www.antaira.com / support@antaira.com
www.antaira.eu / info@antaira.eu
www.antaira.com.tw / info@antaira.com.tw
*Any changes will be announced on the Antaira website.

Tel: 1-844-268-2472
Fax: 1-714-671-9944
www.antaira.com

Documents / Resources

| antaira LNP-2004G-SFP Series 20- Port Industrial PoE pLUS Unmanaged Gigabit Ethernet Switch [pdf] Installation Guide
LNP-2004G-SFP, 20- Port Industrial PoE pLUS Unmanaged Gigabit Ethernet Switch, LNP-2004G-SFP Series 20- Port Industrial PoE pLUS Unmanaged Gigabit Ethernet Switch, Industrial PoE pLUS Unmanaged Gigabit Ethernet Switch, PoE pLUS Unmanaged Gigabit Ethernet Switch, Gigabit Ethernet Switch, Ethernet Switch
---|---