Sogo SS-5675 Multi Coffee Capsule Machine Instruction Manual

Sogo SS-5675 Multi Coffee Capsule Machine

Product Information

The SS-5675 is a Multi Coffee Capsule machine that operates on 220-240V AC with a frequency of 50/60Hz and power consumption of 1450W. It weighs approximately 2.5/3.4 kg and has a maximum pressure of 19 bars. The machine has a water tank capacity of 0.6L and its dimensions are 110mm(W) 270mm(L) 250mm(H). The package includes a water tank, a coffee machine, and a manual.

Product Usage Instructions

Before using the SS-5675 for the first time, or after long pauses, it must be flushed out to clean the internal piping thoroughly. There are two ways to fill the water tank: directly into the machine using a jug or by removing the tank. To fill without removing the tank, raise the water tank cover and fill the tank with cold fresh water up to its maximum level. To fill by removing the water tank, hold the water grip at a tilting angle as shown in the manual, and remove the tank to fill it with water.

To operate the machine, follow these steps:

1. Insert the appropriate filter for the coffee you want to prepare into the brewing basket.
2. Place a cup under the dispenser lever.
3. Press the button for the desired coffee preparation.
4. The coffee will start dispensing into the cup. Wait until it is finished.

The SS-5675 has a standby mode that activates after 15 minutes of inactivity, during which all indicator lights will turn off. To reactivate standby mode, insert the plug into the socket. If the machine deactivates standby mode, it will cancel the mode completely. To activate standby mode again, press the button for standby mode. For cleaning the machine, follow the instructions provided in the manual. Do not open the handle during brewing. In case of further problems or queries, contact the service and sales center.
Note : Keep the packaging for transporting the machine, such as for removals or servicing. You may find a little water remaining in the machine, as it was tested with water before leaving the factory.

Please read this Instruction Manual and the safety instructions before operating the appliance!

Congratulation on your purchase!
This Multi Coffee Capsule machine is manufactured with the greatest care. If you look it after properly it will reward you with many years of good service. Before using your new machine, please read this operating manual carefully, paying particular attention to the safety precautions. This manual can also be downloaded from our website www.sogo.es

Safety precautions

• First, read this entire operating manual.

• The danger of electric shock! Never immerse the machine in water or any other liquid.

• Connect only to a properly grounded PowerPoint.

• To make sure that the machine is switched off, remove the plug from the PowerPoint.

• Always pull out the power plug before:

• Relocating the machine.

• Cleaning or maintenance.

• Long periods of disuse.

• Never clamp or run the power cable over sharp corners or edges.

• The danger of electric shock! Damaged power cables may only be replaced at the customer service center.

• The danger of electric shock! Never touch the power plug/socket/cable or the machine with damp or wet hands. Never unplug by pulling out the power cable; always remove the plug.

• If you need an extension cable, make sure it is suitable for your machine (3-pole grounded, 1.5 mm2 conductor cross-section), and lay the cable to avoid tripping.

• The danger of scalding! Never move the machine during operation!

• Never operate the machine without water.

• Always make sure there is water in the water tank not less than minimum level.

• The danger of burning! Never touch very hot parts of the machine (e.g. brew unit during operations).

• The danger of scalding! Do not touch the steam or water jets.

• The danger of scalding! Do not move the operating lever when the machine is still under pressure making Coffee.

• Do not use the machine in case of:

• Faulty operation.

• Damaged power cable.

• After falling or other damage.

• In such cases immediately have the machine checked and repaired if necessary at the customer service center.

• The machine location must meet the following requirements:

• Choose a dry, stable and level support surface not immediately underneath the PowerPoint at least 60 cm away from the washbasin and taps.

• Never place on flammable/fusible surfaces or equipment.

• Never place the machine or power cable on or nearer than 50 cm to hot surfaces or open flames.

• Never cover the machine during operation.

• Keep children away from the machine during operation.

• Only use the machine in dry rooms.

• The danger of tripping! Do not let the power cable hang down.

• This machine is only intended for household use.

• Pull out the power plug and allow the machine to cool down completely before cleaning and/or Maintenance.

• To prevent damage, never use replacement parts or accessories not recommended by the manufacturer.

• This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Cleaning and user maintenance shall not be made by children without supervision.

• Young children should be supervised to ensure that they don’t play with the appliance.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
  This appliance is intended to be used in household and similar applications such as:

• Staff kitchen areas in shops, offices and other working environments;

• Farmhouses;

• By clients in hotels, motels and other residential-type environments;

• Bed and breakfast type environments.

• Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards.

• Do not touch the surface of the appliance as it can get very hot during operation. Instead, use the handle or mitts.

• The surface of the heating element is subject to residual heat after use. Any misuse can cause potential injury.

NOTES ON THIS OPERATING MANUAL
This operating manual cannot cover all possible circumstances. For further information or in case of problems not adequately covered in this operating manual, please contact the service and sales centre. Please keep this operating manual safe and pass it on to the next user.

UNPACKING

• Remove your Multi Capsule coffee machine from its packaging.

• After unpacking, please check that the following parts are included:

  • Water tank
  • Coffee machine
  • Manual
    Note:

• Check that your home power supply voltage is the same as marked on the machine rating plate.

• Destroy all plastic bags to prevent danger to children!
  Tip:
  Keep the packaging for transporting the machine (e.g. for removals, servicing, etc.).
  Note:
  You may find a little water remaining in the machine. In order to ensure that this machine works perfectly, it was tested with water before leaving the factory.

STARTING UP
Before using it for the first time
Caution: Improper handling of electrical equipment is dangerous and can be lethal. Please pay attention to the safety precautions in this manual, in particular the following:

• The danger of scalding: beware of hot water!
• Do not operate the machine with an empty water tank or water is less than the MINIMUM level.
• Do not open the handle when the machine is brewing.
• Always pull out the power plug before cleaning the machine.
• Only use the machine in a dry room.
• Thoroughly rinse out the water tank with fresh water before using for the first time. Clean the Capsule coffee machine using a damp cloth only.

OVERVIEW OF MACHINE PARTS AND CONTROLS

Before using it for the first time or after long pauses (e.g. holidays) the machine must be flushed out This short procedure can flush out and cleans the internal piping thoroughly.

1. There are two ways to fill the water tank: directly into the machine, by using for example a jug, or by removing the water tank.

Filling without removing the tank

1. Raise the water tank cover.
2. Fill the tank with cold fresh water (the maximum temperature of the water is 35ºC).
3. The maximum capacity is 0.6 liter.
4. Low down the tank cover.

Filling by removing the water tank

1. Hold the water grip at a tilting angle as shown in the direction to remove the water tank from the machine.
2. Fill the tank up to the “MAX” mark with cold fresh water (the maximum capacity is 0.6 liter).
3. Slide the water tank slowly on the water tank base, when the water tank outlet is inserted in the inlet receptacle, push firmly on the water grip as shown in direction 2 to lock the water tank.

Flushing out the machine and internal piping
The lights at the buttons become steady when the machine is heated up, the heating-up time is 45 seconds approximately.

Plug in the appliance and turn it on

Press the small cup / big cup button, and wait for the appliance to complete the flush out.

• Before pressing the button, make sure that:
• The handle is closed without a capsule inside.
• The water tank is full.
• The water tank is firmly in place, otherwise, water may leak a large bowl (250ml size or above) is placed under the dispenser.
• Press the small cup / big cup button to start to flush out.
• Open the handle when the flush-out process stopped automatically.
• Suggest selecting/pressing the big cup button to flush out the machine and the internal pipe.

Tips: The machine has different adaptors for different capsules, details refer below

• For NESPRESSO , STARBUCKS  by NESPRESSO , LAVAZZA & L’OR capsules
• For NESCAFÉ DOLCE GUSTO capsules
• For Ground coffee, tea, infusions, and coffee pods

For NESPRESSO

• Open the handle
• Pull out the brewing basket
• Push in the brewing basket with a capsule
• Close the handle
• Open the brewing basket cover lid.
• Insert a capsule to the brewing basket
• Place a cup under the dispenser
• Press the desired coffee button only once.
• The selected button will blink and the machine will start brewing, brewing will stop automatically when reaches the default brewing time (+/-25S for small cup, +/-47s for big cup), default setting can be changed as per need( please refer to “how to program brewing time” instruction).
• Lift the handle and pull out the brewing basket to remove the used capsule to throw into the garbage container.
• Tips : when pressing the desired coffee button, the led light might flash the light for few seconds and then start brewing.(it means that the machine is heating up).

FOR CÁPSULES NESCAFE DOLCE GUSTO

• Open the handle
• Pull out the brewing basket
• Insert a capsule to the brewing basket.
• Push in the brewing basket with a capsule
• Close the handle
• Place a cup under the dispenser
• Press the desired coffee button only once.
• The selected button will blink and the machine will start brewing, brewing will stop automatically when reaches the default brewing time (+/-25S for small cup, +/-47s for big cup), default setting can be changed as per need( please refer to “how to program brewing time” instruction).
• Lift the handle and pull out the brewing basket to remove the used capsule to throw into the garbage container.
  Tips : when pressing the desired coffee button, the led light might flash the light for few seconds and then start brewing.(it means that the machine is heating up).

FOR GROUND COFFEE, TEA, INFUSIONS, AND COFFEE PODS

• Open the handle

• Extract the adapter basket

• This machine has 2 filters for this adaptor, one for ground coffee/tea and the other for coffee pods

• Change the filter, depending, on what you are going to prepare

• Push in the brewing basket with ground coffee or tea

• Close the handle

• Add the ground coffee, tea or infusion in the coffee adapter and tea

• Press down the ground coffee

• Place a cup under the dispenser

• Press the desired coffee button only once.

• The selected button will blink and the machine will start brewing and then complete the brewing process, dispensing will stop automatically when reaching the default brewing time (+/-25S for small cup, +/-47s for big cup), the default setting can be programmed, please refer to “how to program brewing time” instruction.

• Raise the handle and pull out the brewing basket to throw used coffee into the garbage container.
  Tips: when pressing the button, maybe the desired button LED flashes a few seconds first, then start brewing. the flash process is for heating.

• Note: To prepare tea can be used tea powder or tea bags, to prepare the tea with the tea powder need to use a coffee powder filter and with tea bags coffee pod filter can be used. make sure to remove the string and label, while using tea bags before putting in the adaptor.

STANDBY MODE

1. Factory Default setting: Standby Mode: 15 mins It means the machine will turn off after 15 mins of inactivity and all the indicator lights will go off. Press the switch button to reactivate the standby mode again.
2. Standby mode setting: Keep pressing the small cup button and big cup button, and insert the plug to the socket. The power light will switch on.At this point if standby mode deactivates again, just press the small cup button, the small cup button light turns off and the standby mode get canceled completely. To reactivate the standby mode, press the small cup button again, the small cup button light will turn on again and the standby mode will be reactivated. Factory default setting Press the big cup button, and insert the plug into the socket. The indicator light of the buttons will flash twice. It means the machine comes back to the factory default setting.
3. Coffee Volume Setting Small Cup volume setting Put a coffee cup under the coffee outlet The machine is in normal working condition. Keep pressing the small cup button, then release the button till you get the coffee you want (Min:10S Max:90S)

CLEANING

• Risk of fatal electrical shock and fire. Never immerse the appliance or part of it in water. Make sure to unplug the machine before cleaning.
• Do not use any strong cleaning agent or solvent cleaner.
• Do not use sharp objects, brushes or sharp abrasives.
• Do not place in a dishwasher.

WARNING TIPS

INDUCING THE WATER, MANUALLY INTO THE COFFEE MACHINE AND PUMP
The very first time or after long pauses (e.g. holidays) the machine might not pump the water. So Before using the machine again this short procedure of inducing the water manually into the machine using the pipe, helps the pump and internal circuit to self-priming. Insert the pipe into the water entrance located underneath the water tank. Fill water into the pipe. Push manually with the help of a pusher to introduce the water into the machine, so that the internal circuit get filled with water. After doing the steps mentioned above machine will be able to pump the water on its own. Note: If necessary, repeat the process for 2-3 times.

ENERGY SAVING MODE
The machine enters energy-saving mode automatically once the machine is idle for 15 minutes, the backlight of two buttons and the power indicator will switch off. To quite energy-saving mode, please press the power button, and the appliance will start to warm up with lights blinking, when the buttons are lit steadily, the machine is ready to brew coffee.

DECALCIFICATION
Decalcification / Maintenance
Drinking water varies according to region. The lime particles in hard drinking water are deposited as residues in the machine and can block the piping and cause damage to it. To prevent this, make sure to decalcify the machine at the very least after making 300 to 400 cups of coffee or in any case if the output falls significantly, after one or two months. Decalcification must be done correctly to prevent damage. So, it is essential to follow these instructions.

Important

• Never clean the machine with vinegar. This causes damage and makes your coffee taste bad.
• Damage caused by incorrect decalcification or failure to decalcify is not covered by the guarantee.
• Caution : beware of hot water!
  1. Recommendations: purchase a commercially available decalcifier (decalcifying liquid), diluted according to the manufacturer‘s instructions; pour the mixture in the water tank
  2. Make sure there is without capsule inside the machine.
  3. Place a large bowl under the dispensing head to collect the decalcification diluted and lime residue.
  4. Fill the water tank with water to maximum level mixed with a decalcifying solution, making sure the solution is dissolved completely.
  5. Press the large button to run decalcifying water as you brew coffee normally, repeat several times to run out the entire tank of water.
  6. Repeat the process to run another tank of water mixed with the decalcifying solution.
  7. Repeat the process to Flush out the intern circuit with a tank of fresh water (without the decalcifying solution) to clean the internal circuit completely.

• PROBLEM	CAUSE	SOLUTION
  No coffee is brewed	The water tank is empty	Fill water in the water tank
  The coffee is not hot enough	–  The Cold cups / mugs

–  Scale build-up in machine

–  Cold machine.

| –  Preheat cup / mug

–  Descale

–  For cold machine, brewing a cup of water to warm up the circuit

Water on table| –  The Cold cups / mugs

–  Scale build-up in machine

–  Cold machine

–  Water tank is leaking

–  Drip tray is full of water

| – Check if the valve on water tank is stuck.

–  Empty the drip tray.

Handle can not close| The brewing basket is not placed well| Push the brewing basket into correct position

SPECIFICATION

• Rated Voltage: 220 – 240V AC
• Rated Frequency:  50/60Hz
• Rated Power: 50/60Hz
• N.W./G.W.: 2,5/3,4 kg aprox.
• Pump Pressure: Max. 19 Bars
• Water Tank Capacity: 0.6L
• Size: 110mm(W) 270mm(L) 250mm(H)
• 220 – 240V AC

References

• SOGO. Fabricante y Distribuidor de Electrodomésticos en España.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>