LOOKI Robot Vacuum Cleaner App Instruction Manual
- June 10, 2024
- LOOKI
Table of Contents
LOOKI Robot Vacuum Cleaner App
Product Information
The product is a robot vacuum cleaner that can be controlled through a mobile app. The app can be downloaded from the Play Store or Apple App Store. The robot vacuum cleaner supports only a 2.4 GHz Wi-Fi network. The user manual provides instructions in both Dutch and English.
Product Usage Instructions
- Download the LookiLife App from the Play Store or Apple App Store.
- Open the LookiLife App and register a new account if you don’t have an existing account.
- Login to the app using your credentials.
- Select “Small Home Appliances”.
- Select “Robot Vacuum”.
- Turn on the robot vacuum cleaner by switching on the power button on its side.
- After the startup tone, press and hold the power button for 5 seconds until the Wi-Fi LED indicator starts blinking.
- Select your home Wi-Fi network from the list and enter the Wi-Fi password.
- Confirm that the Wi-Fi LED indicator on the robot vacuum cleaner is blinking and click “Next” to connect.
- Wait for the robot vacuum cleaner to connect to the Wi-Fi network.
- If the connection is lost or you want to connect to another mobile device, reset the Wi-Fi by turning on the robot vacuum cleaner and pressing and holding the power button for 5 seconds until it beeps. Then re-connect it to the Wi-Fi network.
Note : If the robot vacuum cleaner does not respond, click on “Me” in the right bottom corner of the screen, then click on “Home Management > Home Name
Delete Home” to view the reason for the error or click on “Retry” to re- connect the device to the app. The app interface in this manual is for illustration purpose only and may slightly differ from the real app interface.
INSTALLATION INSTRUCTIONS
-
Download the App by scanning the QR code with your mobile device or search for “LookiLife” on Google Play Store or Apple App Store. Before using the app, make sure your mobile device is connected to a Wi-Fi network.
-
Open the “LookiLife” App and register a new account if you don’t have an existing account. Enter the required information to create an account and set a password.
-
After the password is set, login to enter Home, then click on “Add Device
-
Select and click on “Small Home Appliances
-
Select and click on “Robot Vacuum”.
-
Toggle the power switch at the side of the Robot Cleaner to turn on the machine (1 – ON, 0 – OFF), as shown in the figure.
-
After the Robot Cleaner has powered on and the start-up tone is finished, long press the power button on the panel for 5 seconds till the buzzer beeps and Wi-Fi LED indicator flashes.
-
Select the name of your home Wi-Fi and enter the Wi-Fi password, then click on “Next”, as shown in the figure.
Note : Only 2.4GHz Wi-Fi network is supported -
Make sure the Wi-Fi LED indicator on the Robot Cleaner is flashing, then check the “Confirm indicator rapidly blink” box and click on “Next” to connect. Wait for the Robot Cleaner to be added successfully, then click on “Done”. It may take some time for the Robot Cleaner to connect to the Wi-Fi network, depending on the signal strength
Reset Wi-Fi : If the connection times out or before connecting to another mobile device, restart the Robot Cleaner and within 10 seconds, long press the power button for 5 seconds till it beeps, then reconnect to Wi-Fi network Reset WiFi : In case of connection timeout or before connecting another cell phone, first switch on the device and, within 10 seconds, long press the Start/Stop button for 5 seconds till it beeps, and then re-connect it to WiFi network -
Click on “Robot Vacuum Cleaner” to enter the controlinterface, as shown in the figure
-
If the Robot cleaner does not respond, a troubleshooting page will be displayed. Click on “Switch Pairing Mode” to view the reason for the error or click on “Retry” to add the device again
-
To disconnect the Robot Cleaner, click on “Me” at the lower right corner, then click on Home Management > Home Name > Delete Home, as shown in the figure.
Note : To reconnect the Robot Cleaner to App, repeat the previous operations