Joie Calmi Lie-Flat Car Cot Instruction Manual

Joie Calmi Lie-Flat Car Cot

Product Information

The Calmi TM is a lie-flat car cot that is an Integral Specific vehicle ISOFIX Enhanced Child Restraint System. This product is suitable for use with children who have a height of 40cm-70cm and weigh 9kg. The product complies with the European standard the UN Regulation No.129. It has to be installed on i-Base lx 2 or i-Base Encore when used in the car.

Product Parts List

• Handle
• Apron
• Harness Adjustment Strap
• Harness Adjustment Button
• Handle Adjustment Button
• Stroller Attachment Release Button
• Accessory Pocket (maximum load = 1kg)
• Infant Insert
• Buckle
• Shoulder Harness Covers
• Crotch Cover
• Mattress Pad
• Storage Compartment (maximum load = 0.45kg)
• Rain Cover

Product Child Usage Requirements

This product is suitable for use with children who have a height of 40cm-70cm and weigh 9kg.

Product Installation Modes

• Calmi + i-Base lx 2
• Calmi + i-Base Encore

Product Set Up

This enhanced child restraint system is only suitable for vehicle seats equipped with ISOFIX anchorage points. DO NOT install this enhanced child restraint on vehicle seats that face sideways or rearward with respect to the moving direction of the vehicle. Please refer to your vehicle owner’s manual for recommended or suggested installation positions. This enhanced child restraint must be installed on the rear vehicle seat. DO NOT install this enhanced child restraint on movable vehicle seats during installation.

Product Base Installation

1. Attach the ISOFIX guides to the vehicle’s ISOFIX anchor points (see vehicle owner’s manual). The ISOFIX guides can protect the surface of the vehicle seat from being torn. They can also guide the ISOFIX connectors.
2. Connect the ISOFIX connectors to the ISOFIX guides on the vehicle seat.
3. Adjust the support leg to the appropriate length and place it on the floor of the vehicle.
4. Click the infant carrier onto the base and ensure that it is securely attached.

IMPORTANT: KEEP FOR FUTURE REFERENCE. PLEASE READ CAREFULLY. Please keep the instruction manual at the side pocket. If in doubt, consult either the Enhanced Child Restraint System manufacturer or the retailer.

Welcome to Joie™

You have purchased a high quality, fully certified child safety child restraint. This product is suitable for the use of children with height 40cm- 70cm/weight≤9kg. Keep this instruction manual for future reference. This product complies with the European standard the UN Regulation No.129, This is the Integral Specific vehicle ISOFIX Enhanced Child Restraint System. If in doubt, consult either the Enhanced Child Restraint System manufacturer or the retailer.

Base

• These instructions show the use of the infant carrier and the base.
• Please read all the instructions in this manual before installing and using the product.
• IMPORTANT: KEEP FOR FUTURE REFERENCE.
• PLEASE READ CAREFULLY.
• Please keep the instruction manual at the side pocket.

Parts List

1. Handle
2. Apron
3. Harness Adjustment Strap
4. Harness Adjustment Button
5. Handle Adjustment Button
6. Stroller Attachment Release Button
7. Accessory Pocket
   • (maximum load = 1kg)
8. Infant Insert
9. Buckle
10. Shoulder Harness Covers
11. Crotch Cover
12. Mattress Pad
13. Storage Compartment
    • (maximum load = 0.45kg)
14. Rain Cover

• The base is sold separately.

Emergency

• In case of emergency or accidents, it is most important to have your child taken care of with first aid and medical treatment immediately.

Product Information

1. This is an Integral Specific vehicle ISOFIX Enhanced Child Restraint System.
2. If in doubt, consult either the Enhanced Child Restraint System manufacturer or the retailer.
3. calmi lie-flat car cot has to be installed on i-Base lx 2 or i-Base Encore when use in car.

• Materials Plastics, metal, fabrics
• Patent No. Patents pending

Child Usage Requirements

This product is suitable for use with children who meet the following requirements:

• For installation with i-Base lx 2, please refer to i-Base lx 2 manual.

WARNING

• CAREFULLY read the warnings given in the separate Safety Manual to ensure a secure usage of the product.

Product Set Up

• This enhanced child restraint system is only suitable for vehicle seats equipped with ISOFIX anchorage points. 1
• DO NOT install this enhanced child restraint on vehicle seats that face sideways or rearward with respect to the moving direction of the vehicle.
• Please refer to your vehicle owner’s manual for recommended or suggested installation positions. 2
• This enhanced child restraint must be installed on the rear vehicle seat. 3
• DO NOT install this enhanced child restraint on movable vehicle seats during installation.

Product Use

Base Installation.

1. Attach the ISOFIX guides to the vehicle’s ISOFIX anchor points (see vehicle owner’s manual). 4 The ISOFIX guides can protect the surface of the vehicle seat from being torn. They can also guide the ISOFIX connectors.
2. Unfold the load leg from storage compartment. 5
3. Press the ISOFIX adjustment button to adjust the ISOFIX connectors. Line up the ISOFIX connectors with the ISOFIX guides, and then click both ISOFIX connectors into the ISOFIX anchor points. 6
   • Make sure that both ISOFIX connectors are securely attached to their ISOFIX anchor points. There should be two audible clicks and the colors of the indicators on the both ISOFIX connectors should be completely green. 6 -3
   • Check to make sure the base is securely installed by pulling on the both ISOFIX connectors.
4. After placing the base on the vehicle seat, extend the load leg to floor 7. When the load leg is installed correctly, the load leg indicator will show green. Red will be shown when installed incorrectly. 7 -2
   • The load leg has multiple positions. When the load leg indicator shows red this means the load leg is in the wrong position.
   • Make sure the load leg is in full contact with the vehicle floor pan.
   • Squeeze the load leg adjustment button, then shorten the load leg upwards. 7 -1
5. The completely assembled base is shown as 8
   • The ISOFIX connectors must be attached and locked onto the ISOFIX anchor points. 8 -1
6. To remove the base from the vehicle seat, push the secondary lock buttons 9 -1 first and then press the ISOFIX releasing buttons 9 -2 on the ISOFIX connectors before removing the base from the vehicle seat. 9
7. For transporting, press ISOFIX adjustment button and move the ISOFIX connectors back into the storage position. 10

Attachment to the base

1. Pull up the canopy as illustrated while pressing the buttons on both sides. 11
2. Check to make sure the handle is secure before placing the child in the lie-flat car cot. 12 -1
   • Make sure that the handle is in the correct position of use before carrying or lifting.
3. Install the lie-flat car cot onto the base 13, the child restraint indicators should turn green when the lie-flat car cot and base are securely connected. 14
   • Please check that the mesh at the bottom of the lie-flat car cot is fixed properly before installing lie-flat car cot. 13
   • Check that the lie-flat car cot is locked onto the base by lifting the handle.
4. Press the ISOFIX adjustment and push the base back until it comes in contact with the vehicle seat backrest.
5. To release the lie-flat car cot, squeeze the infant carrier release button on the base 15 -1, then lift the lie-flat car cot up. 15 -2
6. When lie-flat car cot is installed on base, the correct installation is shown in 16. The incorrect installation is shown in 17.

Securing Child

1. Remove the lie-flat car cot apron from the velcros on the side. 18
2. Press the harness adjustment button while pulling the both shoulder harnesses of the enhanced child restraint to the desired length. 19 20
3. Undo the buckle by pressing the red button. 21
   • We recommend using the infant insert while the baby is under 60cm and until they outgrow the insert. 22
4. Place child into the enhanced child restraint and engage the buckle. 23 24
5. Tighten the shoulder harness straps by pulling the adjustment webbing. 25
   • Make sure the space between the child and the shoulder harness straps is about the thickness of one hand.
6. Place the apron back on the lie-flat car cot. 26
7. The canopy window can be opened for ventilation. 27

Detach & Assemble Soft Goods

• Follow steps 28 – 40 to detach soft goods.
• To re-attach the soft goods please repeat the above steps in the reverse order.

Cleaning and Maintenance

• Clean the frame, plastic parts, and fabric with a damp cloth, but do not use abrasives or bleach. Do not use silicon lubricants as they will attract dirt and grime. Do not store the lie-flat car cot in a damp place.
• To ensure long-lasting use, wipe this product off with a soft, absorbent cloth after using it in rainy weather and before storing away.
• Refer to the care labels attached to the soft goods for washing and drying instructions.
• It is normal for the fabric to color from sunlight and to show wear and tear after a long period of use, even when used normally.
• For reasons of safety, only use original Joie parts.
• Check regularly if everything functions properly. If any parts are torn, broken, or missing, stop using this product.

Joie  Ltd

Allison Baby UK Ltd,

• Venture Point, Towers Business Park
• Rugeley, Staffordshire, WS15 1UZ

NUNA International B.V.

• Van der Valk Bourmanweg 178 C, 2352 JD Leiderdorp, The Netherlands

view all fine signature selections at joiebaby.com/signature

References

• Joie's Signature Collection | Luxury Baby Gear

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>